Honeywell HBD7S(X) User manual

Document 800-15429 – Rev A – 07/2013
Configuration Guide
Indoor/Outdoor
Bullet Camera
HBD7S(X)

2 | HBD7S(X) Camera Configuration Guide
www.honeywell.com/security
Revisions 1
Issue Date Revisions
A 07/2013 New document.

Regulatory | 3
800-15429 - A - 07/2013
Regulatory 2
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Note Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Canadian Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Manufacturer’s Declaration of Conformance
North America
The equipment supplied with this guide conforms to UL 60065 and CSA C22.2 No. 60065.
Europe
The manufacturer declares that the equipment supplied with this guide is compliant with
the essential requirements of the EMC Directive 2004/108/EC, the General Product Safety
Directive 2001/95/EC and the RoHS Directive 2011/65/EU, conforming to the requirements
of standards EN55022 for emissions, EN50130-4 for immunity, EN60950-1 for electrical
equipment safety, and EN50581 for assessment of electrical and electronic products with
respect to the restriction of hazardous substances.
WARNING: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures

4 | HBD7S(X) Camera Configuration Guide
www.honeywell.com/security
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty
period Honeywell will repair or replace, at its sole option, free of charge, any defective
products returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service
at 1.800.323.4576 (North America) for assistance or to request a Return Merchandise
Authorization (RMA) number. Be sure to have the model number, serial number, and the
nature of the problem available for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to
Honeywell without a clearly identified Return Merchandise Authorization (RMA) number
may be refused.
Waste Electrical and Electronic Equipment (WEEE)
Correct Disposal of this Product (applicable in the European Union
and other European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per
applicable local laws, regulations, and procedures.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNI T.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
DO NOT OPEN
RISK OF ELECTRIC SHOCK

Contents | 5
800-15429 - A - 07/2013
Contents 3
Regulatory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Configuring the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the OSD Joystick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Main Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
AGC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sense-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Backlight Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . 10
D-WDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Day&Night . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3DNR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Special Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Camera Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
D-Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Privacy Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Defect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Defog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Adjust Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6 | HBD7S(X) Camera Configuration Guide
www.honeywell.com/security
General Features
650 TV Lines Resolution
The 1/3-inch color 960H CCD image sensor and digital signal processor combine to
produce 650 TV lines of super high resolution.
3D Motion DNR Function
Smart 3DNR activates automatically to reduce motion blur when moving objects are
present in a scene. This results in better picture quality of scenes with motion and lowers
the storage requirements for storing video.
D-WDR (Digital Wide Dynamic Range)
D-WDR improves image quality in unevenly lit scenes.
Sense-Up
Sense-up automatically activates slow shutter function when a scene is too dark, improving
scene visibility in low-light conditions.
Defog
Defog improves image definition in conditions of poor visibility, such as in fog, smoke, rain,
or snow.
Additional Functions
• On-screen display menu with multi-language support
• 8 privacy masking zones
• 4 motion detection zones

Configuring the Camera | 7
800-15429 - A - 07/2013
Configuring the Camera
Using the OSD Joystick
The camera’s setup menus are controlled using the built-in OSD joystick located on the
underside of the camera.
Figure 1 OSD Joystick
Press down and hold the OSD joystick for two seconds to bring up the OSD menu on the
connected monitor.
OSD Joystick Commands
• To move up or down through a list of menu options, push the joystick up or
down .
• To enter a submenu () or to set a menu selection, press down on the joystick.
• To change a menu setting, push the joystick left or right . If multiple options are
available, keep pushing the joystick left or right until the desired value/status is
displayed.
• To exit a menu, push the joystick up or down until EXIT is selected, and then press
down on the joystick.
SET UP

8 | HBD7S(X) Camera Configuration Guide
www.honeywell.com/security
Main Setup Menu
Open the SETUP menu to make changes to camera configuration.
Figure 2 Setup Menu
To open the SETUP menu, press down and hold the OSD joystick for two seconds.
Lens
Note This camera does not have an interchangeable lens. This camera comes with a
DC drive lens only.
1. Press the joystick to enter the DC LENS menu (see Figure 3).
Figure 3 DC Lens Menu
2. Set the desired BRIGHTNESS level. Select a value between 1and 100. The default
setting is 50.
3. Set the MODE to INDOOR or OUTDOOR, depending on the camera environment.
4. Select RETURN to save your settings and return to the SETUP menu.

Configuring the Camera | 9
800-15429 - A - 07/2013
Exposure
In the SETUP menu, navigate to EXPOSURE, and then press the joystick to enter the
EXPOSURE menu (see Figure 4).
Figure 4 Exposure Menu
Shutter
Set SHUTTER to one of the following: x256, x128, x64, x32, x24, x16, x14, x12, x10, x8,
x6, x4, x2, AUTO (default), 1/60, FLK, 1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000,
1/20000, 1/50000, or 100000.
AGC (Auto Gain Control)
Set AGC to LOW, MIDDLE, or HIGH (default).
Gain is applied as follows:
• LOW: 28 dB
• MIDDLE: 32 dB
• HIGH: 36 dB
A higher AGC setting produces a brighter image in low light, but also more noise.
Sense-Up
SENSE-UP automatically activates slow shutter function when a scene becomes too dark,
increasing image clarity and reducing storage requirements. With higher SENSE-UP
values, however, more motion blurring will be visible in the video image.
Set SENSE-UP to AUTO (default) or OFF.

10 | HBD7S(X) Camera Configuration Guide
www.honeywell.com/security
If AUTO is selected, do the following:
1. Press the joystick to enter the SENSE-UP menu (see Figure 5).
Figure 5 Sense-Up Menu
2. Set SENSE-UP. Select a value from x2 to x256 to set the desired frame integration
level. The default setting is x4.
3. Select RETURN to save your settings and return to the EXPOSURE menu.
BLC (Backlight Compensation)
Backlight Compensation (BLC) increases the brightness of backlit objects in a scene.
Highlight Suppression Backlight Compensation (HSBLC) masks bright objects in a scene.
Set BLC to OFF (default), BLC, or HSBLC.
If BLC is selected, do the following:
1. Press the joystick to enter the BLC menu (see Figure 6).
Figure 6 BLC Menu
2. Set VALUE to LOW, MIDDLE (default), or HIGH.
3. Set the backlight compensation AREA manually or set it to the DEFAULT setting.