Honeywell HD3DS User manual

Document 800-13601V1 – Rev A – 05/2013
Configuration Guide
3 Inch Minidome
High Resolution Indoor
Minidome Camera
HD3DS HD3DSX
HD3HRS HD3HRSX

2
Revisions
Issue Date Revisions
A 05/2013 New document, based on 800-13601; adding HD3DS(X)
models.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
DO NOT OPEN
RISK OF ELECTRIC SHOCK

3
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Programming the Camera. . . . . . . . . . . . . . . . . . . . . . . . . 4
Exposure Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Color Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Day&Night Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Function Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Motion Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Privacy Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4
Introduction
This document provides instructions for configuring the HD3DS(X) and HD3HRS(X) indoor
minidome camera settings. The HD3DS(X) offers true day/night functionality and the
HD3HRS(X) is a day/night version. These instructions are intended for system installers,
administrators, and operators. For information about installing the camera, refer to the 3
Inch Minidome Camera Quick Installation Guide.
Programming the Camera
The camera is programmed using the on-screen display (OSD) menus. You can connect a
portable monitor during installation using the supplied adapter cable.
To show the OSD main menu, press the OSD
controller joystick located on the camera
control board.
Move the joystick up or down to navigate
through the menu options. Move the joystick
right to change a menu setting.
When a menu option or setting is followed by
, press the joystick to access the next
screen. To go back to the main menu, select
RETURNand then press the joystick.
UP
DOWN
RIGHTLEFT

5
The camera has the following OSD menu structure:
1. EXPOSURE
LENS
BACKLIGHT
AGC
SENSE-UP
3D DNR
EXIT JUMP
2. COLOR
WB MODE
RED GAIN
BLUE GAIN
COLOR GAIN
EXIT JUMP
3. DAY&NIGHT
D&N MODE
NIGHT C.
NIGHT A.
EXIT JUMP
4. FUNCTION
MIRROR
SHARPNESS
GAMMA
SLC
NIGHT-UP
EXIT JUMP
5. MOTION
AREA SET
SENSITIV.
SHOW INDI.
EXTER OUT
EXIT JUMP
6. PRIVACY
MASK 1
MASK 2
MASK 3
MASK 4
MASK 5
MASK 6
MASK 7
MASK 8
EXIT JUMP
7. SETUP
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
COMMUNICA.
FACTORY SET
EXIT JUMP
8. EXIT
SAVE&EXIT
EXIT

6
Exposure Menu
EXPOSURE LENS
Note Only DC mode is supported at this time.
Choosing MANUAL mode may cause the camera
to operate incorrectly.
1. Select DC.
2. Set the DC LEVEL to adjust the brightness
level of the monitor screen. Select a value
from 1to 100 (100 = brightest). The default
setting is 30. Set the FOCUS TARGET to
the maximum value for a clear image.
3. Select E. SHUTTER to set the shutter
speed. You can select from 22 different
shutter speeds, from X1024 to 1/100000.
DC-AUTO is the default shutter speed for
both indoor and outdoor use. Select
1/100FLC to run the camera in flickerless
mode.
Note The SENSE-UP menu cannot be
controlled if the E. SHUTTER setting is
above 1/60.

7
EXPOSURE BACKLIGHT
Set BACKLIGHT to BLC (Backlight Compensation), HME (Highlight Masking Exposure),
D.WDR (Digital Wide Dynamic Range), or OFF.
If BLC is selected, do the following:
1. Set BLC MODE to MANUAL or SMART
(recommended).
•IfSMART is selected, the camera
automatically adjusts the BLC.
•IfMANUAL is selected, you can adjust
the BLC level in four areas of the scene
(TOP, BOTTOM, LEFT, RIGHT).
2. Select SET LEVEL to set the BLC level to
LOWEST, LOW, MID, or HIGH.
BLC Backlight Compensation prevents subjects in defined areas of the scene from
appearing too dark when backlighting is present.
HME Highlight Masking Exposure masks bright areas of the scene to allow objects to
appear clearly on the screen.
D.WDR Digital Wide Dynamic Range provides clear images even when strong backlighting is
present.

8
If HME is selected, do the following:
1. Select HME_BLC SET.
2. Set SET LEVEL to LOWEST, LOW, MID,
or HIGH.
3. Define the highlight masking area
(shaded) by adjusting TOP, BOTTOM,
LEFT, and RIGHT.
4. Define MASK 1 (indicated by the outline at
the top left of the screen) by adjusting
TOP, BOTTOM, LEFT, and RIGHT.
5. Set up additional highlight masks if desired.
6. Set MODE to ALL DAY or NIGHT.
7. Select SET LEVEL to adjust the HME level. Select a value from 001 to 100.
The higher the number, the darker the mask.
If D.WDR is selected, do the following:
• Select SET LEVEL and select a value from
0to 20.

9
EXPOSURE AGC (Auto Gain Control)
Auto Gain Control increases picture brightness in low light conditions. However, it also
increases picture noise.
Set AGC to OFF, LOW, MID, HIGH, or HIGHEST.
EXPOSURE SENSE-UP
SENSE-UP automatically activates slow shutter function when a scene is too dark.
Select a value from X2 to X1024 to set the frame integration level. The default setting is X4.
Increasing the shutter speed beyond X4 is not recommended as it may cause lagging.
Note The SENSE-UP menu cannot be controlled if the E. SHUTTER setting
is above 1/60.
EXPOSURE 3D DNR
Digital Noise Reduction reduces the noise/distortion on the screen in night mode, allowing
clear images in low light conditions.
Set 3D DNR to OFF, LOW, MID, HIGH, or SMART (recommended).
SMART optimizes the DNR volume depending on the scene.

10
Color Menu
COLOR WB MODE
Set WB MODE to AWC, ATW, MANUAL, or PUSH.
AWC Auto White Balance Control mode
compensates for color temperature
changes between 2000 K and 18000 K.
ATW Auto Tracking White Balance mode
compensates for color temperature
changes between 2500 K and 9500 K.
MANUAL Manual mode lets you manually adjust
the red gain and blue gain levels (M. WB
RED and M. WB BLUE) while monitoring
the color of the image.
PUSH Push Lock mode fixes the white balance
based on current lighting. For best
results, place a white surface (such as a
piece of paper) in front of camera during
adjustment.