Honeywell MagicStat CT3300 Technical specifications

69-1634-1
INSTALLATION AND PROGRAMMING INSTRUCTIONS
® U.S. Registered Trademark
Copyright © 2003 Honeywell International Inc.
All Rights Reserved
CT3300 Programmable Thermostat
Welcome to the world of comfort and energy savings with your new
Honeywell Programmable Thermostat. Your new thermostat will
automatically control the temperature in your home, keeping you
comfortable while saving energy.
Weekday/Weekend (5-day/2-day)
Programmable Heat and/or Cool
Low Voltage (20 to 30 Vac)
Thermostat and Mounting Plate
Model CT3300
Table of Contents
Installation .................................................................................................................................................................. 2
Programming.............................................................................................................................................................. 11
Operation.................................................................................................................................................................... 17
Frequently Asked Questions ...................................................................................................................................... 22
Customer Assistance ................................................................................................................................................. 23
Limited Warranty ........................................................................................................................................................ 24

69-1634—1 2
MERCURY NOTICE
If you are removing an old thermostat that contains mercury in a sealed tube
(Fig. 1), do not place the old thermostat in the trash. Contact your local waste
management authority for instructions regarding recycling and the proper
disposal of the old thermostat.
Installation
INSTALLATION
Verify You Have Correct Thermostat
Make sure that the CT3300 is the correct thermostat for your heating/cooling system. Read the compatibility chart
below to determine which system you have. If your system is not compatible with the CT3300, the table recommends
an alternate Honeywell model. If you are unsure what type of thermostat is right for your system, visit us on the Web at
www.honeywell.com/yourhome or call Honeywell Customer Care at 1-800-468-1502.
Heating/Cooling System
Compatible
with CT3300? Alternate Model
Conventional
Single stage systems that include warm air furnaces and hot water.
Yes
Electric Baseboard
Electric-powered heating strips located just above the floor, usually 120 to 240
volts.
No CT1950 for 240
volts
M3701
MERCUR
Y
SWITCH
Fig. 1.

3 69-1634—1
Step 1. Prepare for Installation
1. Carefully unpack your new thermostat. Save your receipt and make sure you have the following parts:
• Thermostat and mounting plate.
• Labels.
• Screws and anchors.
• Installation and Programming Instructions.
2. Gather the needed tools and supplies listed below.
3. Make sure that your heating and cooling systems are working correctly. If there is a problem with either system,
call a heating/air conditioning contractor—the problem may persist after you install the new thermostat.
IMPORTANT:
To avoid damaging the compressor in the air conditioner, do not operate the cooling system when the tem-
perature outdoors is below 50°F (10°C).
Steam
A steam boiler with radiator heat.
No CT3600
Heat Pump
Heating and cooling are produced from the same outdoor unit (compressor) with
no auxiliary or backup heat.
No CT3600
Multistage Heat Pump
Heating and cooling are produced from the same outdoor unit (compressor) with
auxiliary or backup heat.
No CT3611
Multistage Conventional
A heating or cooling system with more than one stage.
No See your
contractor
Required Tools and Supplies Optional Tools
• Two AA alkaline batteries. Honeywell recommends Energizer®
batteries.
• Screwdriver.
• Hand or power drill with 3/16-inch or 7/32-inch drill bit.
• Pencil.
• Wire cutter/stripper or sharp knife.
• Level.
• Electrical tape.
Heating/Cooling System
Compatible
with CT3300? Alternate Model

69-1634—1 4
Step 2. Remove Old Thermostat
Fig. 2. a. Turn off power to the heating/cooling system, either at the furnace or
at the fuse/circuit breaker panel.
b. Remove the cover of your old thermostat (Fig. 2).
c. Unscrew and remove the old thermostat’s mounting plate from the
wall, but do not disconnect the wires.
d. Inspect the old thermostat wiring. If wiring meets any of the follow-
ing conditions, see special wiring instructions section after Step
7.
Fig. 3. • The old thermostat is a clock thermostat with wires attached to
the C or C1 terminals.
• The old thermostat has six or more wires, excluding wires
attached to C or C1 terminals.
• The old thermostat has three wires.
• There are five wires connected to the old thermostat.
• There are extra wires that are not connected to the old
thermostat.
e. Using enclosed labels, mark wires with letter of terminal it is attached
to on the old thermostat (Fig. 3). Do not label using colors. If labels
do not match letters on old thermostat terminals, see wiring cross ref-
erence table in Special Wiring Instructions section.
Fig. 4. f. Disconnect the wires from the old thermostat and wrap the wires
around a pencil to keep them from falling back into the wall.
NOTE: Remember, if your old thermostat contains mercury, you
must recycle it. See Mercury Notice for more recycling
information.
✓Check your progress
Your wall should now look like Fig. 4.
M2014
0
M19086
WIRES THROUG
H
WALL OPENING
M20133

5 69-1634—1
Step 3. Install Mounting Plate
Fig. 5. a. Separate the mounting plate from the thermostat using a coin, as
shown in Fig 5.
b. Position the mounting plate on the wall. Be sure the mounting plate is
flush against the wall and none of the wires are trapped behind it.
c. Level the mounting plate and use a pencil to mark the center of the
mounting plate screw holes.
d. Remove the mounting plate and drill holes at the locations marked.
• For drywall, drill two 3/16-inch holes.
• For plaster or wood, drill two 7/32-inch holes.
Fig. 6. e. If installing in drywall, gently tap the anchors (provided) into the drilled
holes until they are flush with the wall.
f. Reposition the mounting plate over the holes, pull the wires through
the wiring opening, and loosely insert the mounting screws into each
of the drilled holes or anchors (Fig. 6).
g. Make sure the mounting plate is level and tighten the mounting
screws.
Fig. 7. ✓ Check your progress
The mounting plate is now mounted on the wall and should look like
Fig. 7.
M20139
M20129
M2012
8
W
R
G
R
c
Y

69-1634—1 6
Step 4. Set Thermostat for Your Type of Heating System
IMPORTANT:
Setting your thermostat correctly for your
type of heating system allows it to maintain
accurate temperature control, minimize
swings in the temperature of the room, and
efficiently run the fan.
a. Use the FUEL SWITCH on the back of
the thermostat to set your new thermostat
for the type of fuel that your heating system
uses: F–gas or oil, or E–electric.
NOTE: This setting enables correct fan
operation.
b. Use DIP switches 1 and 2 on the back of
the thermostat to set your new thermostat
for your type of heating system. See the
Heating System Table on the next page to
find the correct settings.
NOTE: These DIP switches are factory-set for a warm air, gas, or oil heating system.
c. The thermostat is set to display the temperature in degrees Fahrenheit (°F). If you want to display the temperature
in degrees Celsius (°C), turn DIP Switch 3 to Off position.
d. You can install the batteries and program your thermostat now, or you can wait until the thermostat is mounted on
the wall. To install the batteries, see Step 7. To program the thermostat, see the Programming section.
Fig. 8.
M2063
7
R
W Y G
W Y G
C R R
THERMOSTAT BACK
DISPLAY F
DISPLAY C 3 - ON 3 - OFF
FE
FUEL SWITCH
WARM AIR
FURNACE 1 - ON 2 - ON F
1 - OFF 2 - ON F
1 - ON 2 - OFF E
FUEL SWITCH
POSITION
DIP SWITCH
POSITION
HEATING
SYSTEM
C C
C
1
OFF ON
2
3
ON
1
2
3
HOTWATEROR
HIGHEFFICIENCY
ELECTRIC
FURNACE

7 69-1634—1
Heating System Table
Step 5. Wire Thermostat Terminals
Type of System
D I P S w i t c h e s
1 and 2 Fuel Switch
Warm air, gas, or oil heating system with an efficiency rating under 90%.
(The furnace efficiency rating should be on the furnace.)
Use factory setting
1–On; 2–On
F
High-efficiency furnace such as a 90% or greater AFUE (Average Fuel
Utilization Efficiency) unit.
1–Off; 2–On F
Hot water boiler 1–Off; 2–On F
Electric furnace 1–On; 2–Off E
Fig. 9. a. Hold thermostat as shown in Fig. 9.
b. Using the labels on the wires, match letter of your old thermostat wire
with the corresponding terminal on the back of your new thermostat.
NOTE: If letters on old thermostat terminals do not match letters on
new thermostat terminals, all old wires may not need connect-
ing to new thermostat. See Special Wiring Instructions section.
Fig. 10. c. Loosen terminal screws and slip each wire beneath its matching
terminal (Fig 10).
d. Securely tighten terminals.
W
Y
G
R
M2012
5
INSERT
STRAIGHT
UNDER
SCREW HEAD
5
/16 in.
(
8 mm)
S
TRIP
END OF WIR
E
VISIBLE HER
E
M20126

69-1634—1 8
Step 6. Mount Thermostat
Step 7. Install the batteries
Fig. 11. Fig. 12. e. Align the tabs at the top of the thermostat with the
tabs at the top of the mounting plate (Fig. 11).
f. Press the lower edge of the case to latch the
bottom of the thermostat (Fig. 12)
Fig. 13.
Fig. 14.
IMPORTANT:
Batteries must be installed for programming and operation of
the thermostat and heating/cooling system. Honeywell
recommends using Energizer® batteries.
a. Make sure that the System switch is set in the Off position.
b. Using a coin, open the battery door as shown in Fig. 13.
c. Install the batteries. Make sure that the positive and negative termi-
nals are oriented correctly as marked inside the battery case.
d. Replace the battery door.
e. Remove the clear plastic label from the digital display.
✓Check your progress
When the batteries are installed correctly, the digital display flashes all
entries once, then begins to flash a default time and the current
temperature (Fig. 14). The flashing continues until you begin to program
the thermostat. You are now ready to program the thermostat. See
Programming section.
M2013
0
M2013
1
M1719C
REMOVING
BATTERY
DOOR

9 69-1634—1
Special Wiring Instructions
Clock thermostat with C or C1 terminals
A clock thermostat has one or two extra wires attached to C or C1 terminals for clock operation that are not used when
installating your thermostat. They must be insulated from each other to avoid damaging your electrical circuit.
a. Make sure that power to the heating/cooling system is turned off.
b. Locate wires that are connected to clock terminals marked C or C1.
c. As you disconnect the wires, do not allow these wires to touch.
d. Wrap wires separately, using electrical tape to insulate the wires.
e. Place wires to avoid interfering with new thermostat operation. They are not used with your 3300 Thermostat.
f. Continue with the installation.
Six or more wires
If old thermostat has six or more wires (excluding clock wires attached to C or C1 terminals), your heating/cooling
system is a variation of a heat pump or multistage system. See thermostat compatibility table located before
Step 1. Your 3300 Thermostat does not work with such systems and should be returned to the place of purchase.
Three thermostat wires
If you have three wires for heating only and can operate the fan using Fan On switch, the 3300 Thermostat works with
your system. Continue installation procedure. If you have three-wire heating-only system and cannot operate fan using
Fan On switch, the 3300 Thermostat does not work with your system. Contact your heating contractor for installation.
Wires that are not connected to old thermostat
For extra wires that do not connect to your old thermostat, do not label them or connect these wires. Tape them with
electrical tape and place them to avoid interfering with operation of new thermostat. Continue installation procedure.
Five wires connected to old thermostat
Your new thermostat has a factory-installed metal
jumper between the R and Rc terminals (Fig. 15).
Remove jumper before wiring R and Rc terminals.
Fig. 15.
M20127
JUMPER (FACTORY-
INSTALLED). REMOVE
IF 5-WIRE SYSTEM
RR
c
WY G

69-1634—1 10
Old thermostat terminals that do not match new thermostat terminals
Use the table below to wire the new thermostat.
*Remove factory-installed jumper between R and Rc terminals in 5-wire systems.
Old Thermostat
Terminal
Connect to New
Thermostat
Terminal Description
R, RH, 4, V R* Power
Rc, R Rc* Power for cooling
W, W1, H W Heat
Y, Y 1, M Y Cooling
G, F G Fa n
O Do not continue
installation
Changeover in cool (O terminal) or changeover in heat (B terminal).
You have a single-stage heat pump or zoning system. Select an alternate
thermostat model.
B
C, X, B Do not connect Transformer common.
W2, H2Do not continue
installation.
Second stage heat (W2, H2) or second stage cooling (Y2).
You have a multistage heating/cooling system. Select an alternate
thermostat model.
Y2