Honeywell TB3 Series User manual

INSTALLATION INSTRUCTIONS
® U.S. Registered Trademark
Copyright © 2022 Honeywell Inc. • All Rights Reserved
31-00576-01
TB3 Series Communicating Thermostats
FOR 2-PIPE AND 4-PIPE FAN COIL UNITS
APPLICATION
TB3 Series Fan Coil Thermostats are used in individual
rooms or zones in buildings. It is designed for two and
four-pipe fan coil units. TB3 Series has one universal
input as an external sensor (NTC10k) or open/close
contact input, three relay fan outputs, two relay valve
outputs (TB3140), two analog valve outputs (TB3240),
and one EIA-485 (BACnet MS/TP). It controls the fan
coil unit depending on the internal room sensor or
external return sensor temperature.
The following NTC10K sensor and flange are
recommended: VF10-3B65NW and LF-MF
CAUTION
CAUTION
• The authorized service must do assembly,
maintenance, diagnostic, and repair. The device's
power supply is 220 VAC (TB3140) and 24V
AC/DC (TB3240), and it has no internal fuse.
• External protection with max C10A (TB3140)
and C5A (TB3240) circuit breakers are required
in all cases.
• Disconnect the power supply before separating
the front plate.
INSTALLATION
• Read these instructions carefully. Failure to follow
them could damage the product or cause a
hazardous condition.
• Check the ratings in the instructions and the product
to ensure the product is suitable for your application.
The Installer must be a trained, experienced service
technician.
• After installation is complete, check out product
operation as provided in these instructions.
• All wiring must agree with applicable codes,
ordinances, and regulations, as specified in
installation wiring diagrams.
• TB3 Series thermostat safety rules are in accordance
with the latest technological developments designed
and manufactured. Adhere to the safety precautions
to avoid injury and property damage.
CAUTION
CAUTION
Power off the supply at circuit breaker or fuse
before installation to avoid fire, shock, or death!

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
31-00576-01 2
DIMENSIONS AND OVERVIEW
ORDERING INFORMATION
Part number TB3240B/U TB3240W/U TB3140B/U TB3140W/U
Digital Outputs (Relay) Fan Control 3 3 3 3
Analog Outputs (0-10 V) Valve
Control 2 2 0 0
Relay Output Valve Control 0 0 2 2
Universal Input 1 1 1 1
Colour Black White Black White
Power 24 V AC/DC,
50/60 Hz
24 V AC/DC,
50/60 Hz
220 V AC, 50/60
Hz
220 V AC, 50/60
Hz

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
3 31-00576-01
PRODUCT SPECIFICATION
Network Security
Honeywell hereby expressly states that the TB3 Series
Communication Thermostat are not inherently
protected against all cyber-security risks from the
Internet and are thus intended solely for use in private
or protected networks.
BACNET and Modbus protocols are open standards
with no security.
Table 1 Display
Parameter Specification
Display Type LCD 62 x 44 mm
Backlight White LED
Buttons 5 integrated capacitive touch areas
Fascia Tempered glass
Table 2 Communication
Parameter Specification
Communication 1 x EIA-485(BACnet MS/TP)
TIA/EIA 485 Cabling specifications
An MSTP EIA-485 network shall use shielded, twisted
pair cable. It means the cable is wrapped with a foil or
braided copper shield throughout its entire length. By
connecting the shield to a single ground point,
induced transients should often be reduced and
directed to ground.
Recommendation :
Wire Size: 22-24 AWG
Cable Type: Twisted-pair, copper wire, tinned
Shield: Braid
Nominal Impedance: 100-120 Ohms
Table 3 Electrical
Parameter Specification
Power Supply
TB3240B/TB3240W : 24V AC/DC,
50/60 Hz
TB3140B/TB3140W : 100~220 VAC,
50/60 Hz
Power
Consumption
(Display ON)
Max ~3.0 VA
Terminal Size
For Power: Up to 16 AWG / 1.5 mm2
For RS485 and NTC: Up to 17 AWG /
1 mm2
Battery for Real
Time Clock (RTC) Lithium CR1220 3.3 V
Table 4 Sensors and Inputs
Parameter Specification
Temperature
Accuracy 1 °C (1.8 °F)
UI Input
Measuring
Range
-10 °C to 100 °C (14 °F to 212 °F)
Inputs 1 Universal Input (NTC 10K or Dry
Contact)
Outputs
3 Digital Outputs (3 Relay*)
2 Relay Valve Outputs (2 Relay*)
(TB3140)
2 Analog Outputs (2 x 0-10 V)
(TB3240)
(*) 5A for resistive loads and 2A for
inductive loads
Table 5 Operating Environment
Parameter Specification
Operating
Temperature
Range
10 °C to 55 °C (50 °F to 131 °F)
Temperature
Setting
5 °C to 40 °C (Adjustable),
(41 °F to 104° F (Adjustable)
Table 6 Other Specifications
Parameter Description
IP Rating IP30
Terminal
Connections Rising cage clamp, Screw terminal
Standard and
Compliance CE, RoHS, BTL certified (B-ASC)
Material of
Casing
Flame retardant ABS and
Polycarbonate (PC)
Table 7 Weight and Dimensions
Parameter Specification
Dimension (L x W x D) 86 x 86 x 52 mm
Weight TB3140 : 208 grams
TB3240 : 207 grams
Minimum depth of
Wall box 52 mm
Mounting Flush Mounted (Standard EU
box)
Table 4 Sensors and Inputs
Parameter Specification

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
31-00576-01 4
MOUNTING
The thermostat must be installed indoors, with around 1.5m height above the floor, representing the average room
temperature. It should be away from direct sunlight, any cover, or any heat source, to avoid false signals for
temperature control. The thermostat should be installed in an area that is not accessible to unauthorized people.
INSTALLATION
NOTE:
This Communicating thermostat is suitable for mounting on standard 75 X 75 X 52 mm Honeywell
recommended back box as per BS4662:2006 + A1:2009 standard or equivalent.
The installation of the device should be performed by an authorized technician. Install the thermostat using
the screws provided in the box.
Steps to Install the TB3 Communicating Thermostat:
1. Switch OFF the power supply before initiating the TB3 installation.
2. Loosen the bottom screw by turning it anticlockwise with the help of a screwdriver.
3. Separate the front panel and base by pulling out from the bottom to do the wiring.

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
5 31-00576-01
4. Pull the power cable and communication cables through the wall box.
5. Connect the wires well according to the wiring diagram. Refer to Wiring Connection on page 6.
6. Fix the base with four screws to the wall box.
7. Attach the front plate to the back plate, making sure the pin plates on each side are well matched.
8. Tighten the bottom screw to fix the front panel and base.
9. Switch ON the power supply to start the TB3 wall module.

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
31-00576-01 6
WIRING CONNECTION
There are two types of modulating connection diagrams. Refer to the wiring diagram that corresponds to the series
you are using.
TB3140 Modulating Connection Diagram
TB3240 Modulating Connection Diagram
NOTE:
The thermostat has no internal fuse. External protection with max C5 A circuit breaker is required in all cases.
Isolate the cables of NTC-dry contact from 230 V(TB3140), 24V AC/DC (TB3240) power supply. The product
supply does not include a 5A fuse.
Connection Diagram for 2-Pipe Fan Coil Connection Diagram for 4-Pipe Fan Coil
Connection Diagram for 2-Pipe Fan Coil Connection Diagram for 4-Pipe Fan Coil

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
7 31-00576-01
USERS INTERFACE
The TB3 thermostat user interface consists of a multi-segment display and five function keys.
NOTE:
When Time Schedule is enabled, and the Local/Remote selection point is set to “Local Control,” the On/Off
button is locked. If “Remote Control” is chosen, the On/Off key will be unlocked even if the user has locked it.
After a certain time, the value of the Local/Remote selection point will be changed to “Local Control.” The user
will not be able to change the Key Log value at this time.
Name Key
Symbol Description
On/Off
Key Switch device state on/off.
Mode
Key
1. Mode Selection: To change the modes, press the mode key. The modes available for
selection will vary depending on the available pipe system.
• For 2-Pipe System, modes available are - Cooling, Heating, and Ventilation.
• For 4-Pipe System, modes available are - Auto, Cooling, Heating, and Ventilation.
NOTE:
In 2 pipe systems, the device will operate in the auto mode based on the supply water
temperature measured from the changeover sensor if it is selected. In this case, the user
will not be able to change the mode.
2. Time Selection: As soon as the mode key is pressed for three seconds, the year will appear
on the screen, followed by the month, hour, minute, and day of the week on successive taps.
To adjust the required time, use the up and down arrow keys.
3. Schedule Operation: After selecting the day of the week in the time selection, press the
mode key again to enter the schedule menu. The sequence of events to configure the
schedule is as follows:
When in schedule mode, “Monday opening time hour digit” displays > Tap the mode key to
enter the edit mode and use up and down to configure the parameter > Tap the mode key
again to display “Monday closing time minute digit” > Tap the mode key to enter the edit
mode and use up and down to configure the parameter.
4. Key Lock Operation: Pressing the mode key along with the up key displays the lock on the
screens and locks the panel. To unlock, press the same combination of keys again. “Key
Lock” options can be changed via parameter P6. Refer to the Configuration Menu
Parameters on page 12.
Up Key Increase the set value.
Down
Key Decrease the set value.
Fan Key Change the fan speed to low, medium, high, and automatic.

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
31-00576-01 8
TROUBLESHOOTING
Trouble Possible Cause Solution
The system is not
cooling, even though the
set point is correct.
Cooling mode is not
activated
• Use key to set the mode to (Cooling).
• Check if the set point is lower than room temperature.
• Be sure the (Cooling Valve icon) is displayed.
• After a while, check whether the system starts cooling.
The system is
continuously
overcooling, even though
the set point is correct.
Heating mode is
activated
• If the system is continuously over cooling, change the
(Mode) to (Cooling) and wait for the (Cooling Valve
icon) to close.
• Please contact your Technical Support if issue persists.
IMPORTANT:
Do not select (Heating) mode in case there is no
provision for heating/hot water pipes.
The system is not
heating, even though the
set point is correct.
Heating mode is
activated
• Use key to set the mode to (Heating).
• Check if the set point is higher than room temperature.
• Be sure the (Heating Valve icon) is displayed.
• After a while, check whether the system starts heating.
The system is
continuously
overheating, even
though the set point is
correct.
Cooling mode is not
activated
• If the system is continuously overheating, change the
(Mode) to (Heating) and wait for the (Heating Valve
icon) to close.
• Please contact your Technical Support if issue persists.
IMPORTANT:
Do not select (Cooling) mode in case there is no
provision for cooling/chilled water pipes.
Keypad doesn’t work /
Keys do not respond Key lock is activated Press and keys together for a while to remove the key lock.
Forgot Password
Contact your system administrator to learn the “Parameter
Menu Password” from the communication line.
• Please press
• Press and keys together for a while to perform a factory
reset.

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
9 31-00576-01
PASSWORD SETTING
IMPORTANT:
It is recommended that a 4-digit pin be set during the first installation. The pin should be kept confidential and
should be changed frequently.
Users must set a password when the thermostat is installed for the first time or restored to factory settings. The
thermostat will display a screen to configure the password in these cases. The password digit can be selected using
the “Main Parameter Increase Key” (Mode Key). The value of that digit can be changed using the “Value Increase
Key” (Up key) and “Value Decrease Key” (Down key). The password entered during the thermostat's setup must be
confirmed with the Fan key.
When the correct password is entered, the configuration menu is displayed. If the incorrect password is entered, the
process will fail, and the password will be reset. After 3 incorrect password entries, new password cannot be entered
for 180 seconds.
The thermostat returns to the main screen if no action is taken within 10 seconds. In 30 seconds, the parameter
setting screen will return to the main screen if no action is taken. All parameters are stored in the device, ensuring no
data is lost if the thermostat is turned off.
NOTE:
Password rules
• There can be no blank spaces.
• All digits cannot be the same.
CONFIGURATION
Configuration Menu Description
To enter the Configuration Menu, hold down the “Main Parameter Increase Key” (Mode Key) and the “Value Decrease
Key” (Down key) for 3 seconds while the device is turned on or off.
For parameter details refer to the Configuration Menu Parameters on page 12.

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS
31-00576-01 10
Universal Input (P32 or via BACnet)
Fan/Valve Control Selection (Parameter P41 or via BACnet)
The fan operates in valve-independent mode using manual fan selection or automatic fan control. When the valve
is closed, the fan continues to operates.
The fan will not operate in valve-dependent mode when the valve is closed. The fan operates according to manual
fan selection or automatic fan control when the valve is open.
Hysteresis (Parameter P40 or via BACnet)
The output diagram of the valve according to the relation between TS and TR
Parameter Definition Description
P32 = 0 Not Used The device operates based on the value of the internal
temperature sensor.
P32 = 1 External Sensor for room The device operates based on the value of the external
temperature sensor read from the universal input.
P32 = 2 External Sensor
The device operates based on the value of the internal
temperature sensor. The temperature read from the universal
input can be monitored from P36.
P32 = 3 Changeover sensor
If the “Universal Input” value is selected as changeover, “dead
zone” cannot be used. The changeover sensor is only valid when
the “Fan Coil Type” is set to 2.
When the water temperature exceeds P34, the thermostat
changes to heating mode and stays in heating mode until the
temperature falls below P33.
When the water temperature is below P33, the thermostat
changes to cooling mode and stays in cooling mode until the
temperature rises above P34.
P32 = 4 Windows contact/Energy
saving-On/Off (NC Contact)
When this contact is closed, the device will work with normal
operation. If this condition is not met, the device displays “OPEN”
on the panel, and the device outputs are passive.
P32 = 5 Windows contact/Energy
saving-Off/On (NO Contact)
When this contact is opened, the device will work with normal
operation. If this condition is not met, the device displays “OPEN”
on the panel, and the device outputs are passive.