Honeywell VisionPRO 8000 User manual

Honeywell
VisionPRO TM8000 Touchscreen
ProgrammableThermostat
APPLICATION
The VisionPRO 8000 Touchscreen Programmable Thermostat
is an effortless, 7-Day programmable thermostat that provides
universal system compatibility, precise comfort control and is
easy-to-program.
The TH8110 Thermostats provide temperature control for gas,
oil, electric and heat pumps for 1 heat, 1 cool systems.
The TH8320 Thermostats provide temperature control for gas,
oil, electric and heat pumps for up to 3 heat, 2 cool systems
including dual fuel operation.
The TH8321 Thermostats provide temperature control for gas,
oil, electric and heat pumps for up to 3 heat, 2 cool systems
including dual fuel operation plus dehumidification control.
FEATURES
• Large, clear display with backlight shows the current
and set temperature and time--even in the dark.
• Menu-driven programming make setup effortless.
• Beautiful ergonomic design is smart and sophisticated
to match your customers' lifestyle.
• Touchscreen interaction
• Real-time clock keeps time during power failures and
automatically updates to daylight savings.
• "Saving Changes" notification lets you know when the
schedule changes have been saved.
• Change/check reminders let you know when to service
or replace filters or batteries.
• Various Hold options allow you to override the
program schedule, as desired.
• Speedy same-schedule programming--no need to
copy multiple days.
• Armchair programming allows you to remove the
thermostat from the wall for programming.
• Programmable fan offers increased air quality when
combined with a Honeywell whole-house air cleaner.
Contents
Application/Features .......................................................... 1
Specifications/Ordering information .................................. 2
Installation ......................................................................... 4
Wiring ................................................................................ 5
Power the Thermostat ....................................................... 11
Installer Setup ................................................................... 15
Installer System Test ......................................................... 20
Operation ........................................................................... 21
Programming ..................................................................... 23
Troubleshooting ................................................................. 38
® U.S. Registered Trademark
© 2004 Honeywell International Inc.
All Rights Reserved 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
SPECIFICATIONS
Thermostat Description:
Feature
Powering methods
System types (up to
3 heat/2 cool or up
to 1heat!1 cool,
depending on
model)
Description
•Battery only
• Common wire only
• Common wire with battery backup
• Gas, oil or electric heat with air
conditioning
• Warm air, hot water, high-efficiency
furnaces, heat pumps, steam and
gravity
• Heat only--includes power to open
and power to close zone valves
(series 20) and normally-open zone
valves
• Heat only with fan
• Cool only
• 750 mV heating systems
Changeover Manual or Auto changeover selectable
System setting Heat-Off-Cool-Auto (Era. Heat for heat
pumps)
Fan setting Auto-On-Circ
Electrical Ratings:
Terminal Voltage (50/60 Hz) Running Current
W Heating 20 - 30 Vac .02 - 1.0A
W Heating 750 mV dc 100 mA dc
(Powerpile)
Y Cooling 26 - 30 Vac .62 - 1.0A
G Fan 20 - 30 Vac .62 - .60A
Temperature Setting Range:
Heating: 40°F to 90°F(4.5°C to 32°C).
Cooling: 50°F to 99°F (10°C to 37°C).
Operating Ambient Temperature:
TH8000 VisionPRO TM Thermostats: 0°F to 120°F
(-18°C to 49°C).
C7089U: -40°F to 120°F (-4O°C to 49°C).
C7189U: 45°F to 88°F (7.2°C to 32°C).
Shipping Temperature:
TH8O00 VisionPRO TM Thermostats: -30 °F to 150 °F
(-34.4°C to 65.6°C).
Operating Relative Humidity (Non-condensing):
TH8000 VisionPRO Thermostats: 5% to 90%.
C7089U: 5% to 95%.
C7189U: 5% to 95%.
Humidity Setting Range (TH8321 models only):
Cooling: 40% to 80% RH.
Humidity Display Range (TH8321 models only):
0% to 99%.
Cycle Rates (at 50% Load):
Heating: Selectable 1 - 12 cycles per hour.
Cooling: Selectable 1 - 6 cycles per hour.
Finish:
TH8O00 VisionPRO TM Thermostats: Premier White@ color.
C7189U Wall Mount Remote indoor Sensor: Premier White@
color.
Clock Accuracy: +/- 1 minute per month.
Batteries:
Three replaceable AAA alkaline batteries: Power thermostats
when 24 Vac common is not used. Non-replaceable
lithium battery with ten-year life under normal use to hold
calendar and time settings. Alkaline batteries keep calen-
dar and time after lithium battery is no longer functional.
Resistance Characteristics of Remote Sensors:
C7089U Outdoor Sensor: Negative temperature coefficient
(NTC) means that resistance decreases as the
temperature increases. See Table 13 in the Operation
section for sensor resistance characteristics.
C7189U Remote indoor Sensor: Negative temperature
coefficient (NTC), means that resistance decreases as the
temperature increases. See Table 14 in the Operation
section for sensor resistance characteristics.
Cool Indication:
TH8OO0 VisionPRO TM Touchscreen Thermostats show "Cool
On" on the screen when Cool is activated.
Heat Indication:
TH80O0 VisionPRO TM Touchscreen Thermostats show "Heat
On" on the screen when Heat is activated.
ORDERINGINFORMATION
When purchasing replacement and modernization products from your TRADEUNE® wholesaler or distributor, refer to the
TRADELINE® Catalog or price sheets for complete ordering number.
If you have additional questions, need further information, or would like to comment on our products or services, please write or
phone:
1. Your local Honeywell Automation and Control Products Sales Office (check white pages of your phone directory).
2. Honeywell Customer Care
1885 Douglas Drive North
Minneapolis, Minnesota 55422-4386
In Canada--Honeywell LimitedlHoneywell Limitee, 35 Dynamic Drive, Scarborough, Ontario MlV 4Z9.
International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,
Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.
68-0280 2

VisionPRO TM 8000 Touchscreen Programmable Thermostat
Auxiliary Heat Indication:
TH8000 VisionPRO TM Touchscreen Thermostats show "Aux.
Heat On" on the screen when Auxiliary Heat is activated.
Emergency Heat Indication:
TH8000 VisionPRO TM Touchscreen Thermostats show "Heat
On" on the screen when Emergency Heat is activated and
the System mode is in the Era. Heat position.
Calibration:
C7089U, C7189U and TH8000 VisionPRO TM Touchscreen
Thermostats are factory-calibrated and require no field
calibration.
Interstage Differential:
TH8000 VisionPRO TM Touchscreen Thermostats operate with
droopless control. Once the thermostat senses that
1st stage is running at 90% capacity, the thermostat
energizes 2rid stage.
Nomenclature:
System Power and System
Series Stages Application Changeover
VisionPRO TM 11 - 1H/1C 0 - Standard U - Universal (Auto
8000 32 - 3H/2C 1- Humidity changeover and/or
Touchscreen Sensor manual change-
over) dual powered,
system flexibility,
schedule flexibility.
Mounting Means:
TH8000 VisionPRO TM Touchscreen Thermostat: Mounts
directly on the wall in the living space using mounting
screws and anchors provided. Fits a vertical or horizontal
2 x 4 in. junction box.
C7089U Outdoor Sensor: Mounts outside of living space with
mounting clip and screws provided.
C7189U Remote indoor Sensor: Mounts directly on the wall
using mounting screws and anchors provided. Fits a
vertical 2 x 4 in. junction box.
Cover Plate:
32003796-001 Cover Plate is used to cover marks left on the
wall by the old thermostat.
Dimensions:
TH8000 Touchscreen Thermostat: see Fig. 1.
C7089U Outdoor Sensor Mounting Clip: see Fig. 2.
32003796-001 Cover Plate: see Fig. 3.
C7189U Remote indoor Sensor: see Fig. 4.
WALLPLATE
3-S/8 (86)
/
THERMOSTAT
6 (152)
THERMOSTAT
AND WALLPLATE
4-9/16
(116)
M22421
Fig. 1. TH8000 Touchscreen Thermostat
dimensions in in. (mm).
1-1/2 (38) d
Fig. 2. C7089U Outdoor Sensor Mounting Clip
dimensions in in. (mm).
O
7-7/8 (200)
3-5/16(84) -_
@ o
M22139
0
Fig. 3. 32003796-001 Cover Plate dimensions in in. (mm).
3 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
4-5/8
(117)
ttoneyweil
I_-----"""- 2-3/4 (70)-_--_-I
M4465 FRONT VIEW
_'_ 1-118 --'_'1
(29)
SIDE VIEW
V
4-5/8
(117) 3-I/4
(83)
B:g C:_
¢ }
2-3/4 (70)
FRONT VIEW (COVER OFF)
Fig. 4. C7189U Remote Indoor Sensor dimensions in in. (mm).
INSTALLATION
When Installing this Product...
1. Read these instructions carefully. Failure to follow the
instructions can damage the product or cause a hazard-
ous condition.
2. Check the ratings given in the instructions to make sure
the product is suitable for your application.
3. Installer must be a trained, experienced service
technician.
4. After completing installation, use these instructions to
check out the product operation.
Selecting Location
Install the thermostat about 5 ft. (1.5m) above the floor in an
area with good air circulation at average temperature. See
Fig. 5.
M19925
Fig. 5. Selecting thermostat location.
Do not install the thermostat where it can be affected by:
-- Drafts or dead spots behind doors and in corners.
-- Hot or cold air from ducts.
-- Radiant heat from sun or appliances.
-- Concealed pipes and chimneys.
-- Unheated (uncooled) areas such as an outside wall behind
the thermostat.
Installing Wallplate
CAUTION
Electrical Hazard.
Can cause electrical shock or equipment damage.
Disconnect power before wiring.
The thermostat can be mounted horizontally on the wall or on
a 4 in. x 2 in. (101.6 mmx 50.8 mm) wiring box.
1,
2.
3.
Position and level the wallplate (for appearance only).
Use a pencil to mark the mounting holes.
Remove the wallplate from the wall and, if drywall, drill
two 3/16-in. holes in the wall, as marked. For firmer
material such as plaster, drill two 7/32-in. holes. Gently
tap anchors (provided) into the drilled holes until flush
with the wall.
68-0280 4

VisionPRO TM 8000 Touchscreen Programmable Thermostat
4. Position the wallplate over the holes, pulling wires
through the wiring opening. See Fig. 6.
5. Insert the mounting screws into the holes and tighten.
WALL
W_RES THROUGH WALL
WALL ANCHORS (2)
_a
HOLES
SCREWS(2)
Fig. 6. Mounting wallplate.
WIRING(FIG.9- 21)
All wiring must comply with local electrical codes and
ordinances.
1. Select set of terminal identifications (Table 1) that
corresponds with system type (conventional or heat
pump in Fig. 7).
2. Loosen the screws for the appropriate system type
selected; see Table 1. See Table 2 for terminal
designation descriptions. Insert wires in the terminal
block under the loosened screw. See Fig. 8.
3. Securely tighten each screw.
4. Push excess wire back into the hole.
5. Plug the hole with nonflammable insulation to prevent
drafts from affecting the thermostat.
6. See Fig. 9 through 21 for typical wiring hookups.
_c HEATPUMP
ONVE TIONAL]
'Z SCREWTER_._,NALSJ _,_
Table 1. Selecting Terminal Identifications for
System Type.
Wallplate Wiring
Terminal Diagram
System Type Identifications Reference
Standard Heat/Cool Conventional 9, 10
Heat Only Conventional 11
Heat Only with Fan Conventional 12
Heat Only (Series 20) Conventional 13
Power to open and
power to close zone
valves
Normally Open Zone Conventional 14
Valves--Heat Only
Cool Only Conventional 15
Standard Multistage up Conventional 16, 17
to 2 Heat/2 Cool
Heat Pump with No Heat Pump 18, 19
Auxiliary Heat
Heat Pump with Heat Pump 20, 21
Auxiliary Heat
Fig. 8. Inserting wires in terminal block.
IMPORTANTUse 18 gauge thermostat wire.
Fig. 7. Selecting terminal identifications for
system type.
5 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
Table 2. Terminal Designation Descriptions.
Terminal
Designation Description
Rc (see Note Power for cooling--connect to
1) secondary side of cooling system
transformer
R (see Note 1) Power for heating--connect to
secondary side of heating system
transformer
C (see Note 2) Common wire from secondary side of
cooling system transformer
W Heat relay
Y Compressor contactor
G Fan relay
Y2 Second stage cooling
W2 Second stage heat relay
O/B (see Note Changeover valve for heat pump
3) systems
AUX Auxiliary heat relay for heat pump
systems
E Emergency heat relay for heat pump
systems
L (see note 4) Equipment monitor for heat pump
systems
Sl, S2 Optional outdoor or indoor remote
sensor
NOTES:
1.
2.
3.
When used in a single-transformer system, leave
metal jumper wire in place between Rc and R. If
used on a two-transformer system, remove metal
jumper wire between Rc and R.
Common wire is optional when thermostat is used
with batteries.
If thermostat is configured for a heat pump system
in the Installer Setup, configure changeover valve
for cool (O-factory setting) or heat (B).
L terminal is an input (system monitor) when the
System mode is in the Heat, Off, Cool or Auto
position. L terminal is a 24 Vac output when
System mode is Emergency Heat. Must connect
the 24 Vac Common when using the L terminal.
See LED Indication section for more details.
_CONVENTI_NAL
W2
5_1__
L..J,--zsmJ--] i
II
i,
II
II
II
I OUTDOOR/INDOOR I
TEMPERATURE
SENSOR
RC
Y ©
G @ OPTIONAL
24 VAC
COMMON
CONNECTION
pATREL4
A
Z_ POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED
Z_ FACTORY INSTALLED JUMPER
A OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR AVAILABLE
ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE M19895
Fig. 9. Typical hookup of conventional single-stage heat
and cool system with single transformer
(IH/lC conventional).
_ CONVENTIONAL
W2
3_1__
II
II
A" o
I OUTDOOR/INDOC_'_1
TEMPERATURE
SENSOR
G
° o o /,O AL
i COMMON
CONNECTION
IHEATRELAYI
A
A
A POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED
Z_ REMOVE FACTORY INSTALLED JUMPER
OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR AVAILABLE
ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE M19896
Fig. 10. Typical hookup of conventional single-stage heat
and cool system with two transformers
(1H/IC conventional).
68-0280 6

VisionPRO TM 8000 Touchscreen Programmable Thermostat
_ CONVENTIONAL
i_Y2 Rc
Jl l_!llw2 w_u
il 1_-_14s"
i_L. s___I OPTIONAL
i_A L 24VAC
COMMON
tCONNECTION
_HEAT RELAY
Z_ POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED
Z_ FACTORY INSTALLED JUMPER
Z_ OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR AVAILABLE
ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE M19897
Fig. 11. Typical hookup of heat-only system
(1 H conventional).
2
W2
S_1__
21
II
II
II .
I OUTDOOR/INDOOR I
TEMPERATURE
SENSOR
_ CONVENTIONAL
Y @
G @
[
L
OPTIONAL
24VAC
COMMON
CONNECTION
Z_ POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED
,,_ FACTORY INSTALLED JUMPER
/_ OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR AVAILABLE
ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE M19898
Fig, 12. Typical hookup of heat only system with fan
(1H conventional).
_ CONVENTIONAL
W2
S_1__
2
'Ail,, [1_
ii
i OUTDOORIINDOOR
TEMPERATURE
SENSOR
I
Y @
G @
L
I
z_ POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED
z_ FACTORY INSTALLED JUMPER
OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR AVAILABLE
ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE M19899
Fig. 13. Typical hookup of heat only power to open and
power to close zone valve (Series 20) system.
_CONVENTIONAL
W2
S1
---I
II
PP
II
A!!
_ JL_ ]
TEMPERATURE N __
SENSOR
Z_X POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
Z_ FACTORY INSTALLED JUMPER.
Z_ OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR. AVAILABLE
ON SELECT MODELS. WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE.
Z_ CONFIGURE SYSTEM TYPE TO HEAT ONLY WITH NORMALLY OPEN
ZONE VALVES IN INSTALLER SETUP. M22422
Gi_G__ OPTIONAL24VAC
tCOMMON
Pl CONNECTION
Fig. 14. Typical hookup of heat only system with normally
open zone valves.
7 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
_CONVENTioNAL •
-2-11 Q OPTIONAL
ii ['
_Ax_ i
TEMPERATURE __ COMPRESSOR __
SENSOR CONTACTOR
Z_ POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED
Z_ FACTORY iNSTALLED JUMPER
A OPTIONAL OUTDOOR OR iNDOOR REMOTE SENSOR AVAILABLE
ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE M19900
Fig. 15. Typical hookup of cool only system
(IC conventional).
_CONVENTI_NAL
W2
I t_lJ_S_2_l
II II
ll_
A ii
- i
OUTDOOR/INDOOR
TEMPERATURE
SENSOR
_HEAT RELAY
I
_C
W_ OPTIONAL
24VAC
Y G COMMON
CONNECTION
G Q MUSTCOME
FROM THE
COOLING
TRANSFORMER.
3OOL RELAY 2
A
AR
C
Z_ POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
Z_ FACTORY INSTALLED JUMPER.
Z_ OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR. AVAILABLE
ON SELECT MODELS. WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE. M19902B
_CONVENTIONAL
A
OUTDOOR/INDOOR
TEMPERATURE
SENSOR
HEAT RELAY
OPTIONAL
24VAC
COMMON
CONNECTION
MUSTCOME
FROM THE
COOLING
TRANSFORMER
COOL RELAY 1
Z_ POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
z_ FACTORY INSTALLED JUMPER.
Z_ OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR. AVAILABLE
ON SELECT MODELS. WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE. M22438B
Fig. 17. Typical hookup of conventional multistage
two-stage heating and two-stage cooling in a
two-transformer system (2H/2C, 2H/1C or
IH/2C conventional).
Fig. 16. Typical hookup of conventional multistage
two-stage heating and two-stage cooling in a
single-transformer system
(2H/2C, 2H/IC or 1H/2C conventional).
68-0280 8

VisionPRO TM 8000 Touchscreen Programmable Thermostat
........ HEATPUMP
i.............
,
, _i®[--
AUX , -@E Y
-®E G
--- __ coO_To'O;'_NI_E)Sb".....
OUTDOOR/iNDOOR -J
4 I 1
1c°MPREss°R1RELA_
Z_ POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED
Z_ FACTORY INSTALLED JUMPER
Z_ "O/B" TERMINAL SET TO CONTROL AS EITHER "O" OR "B" IN THE INSTALLER SETUP
z_ OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR AVAILABLE ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE
Fig. 18. Typical hookup of single-stage heat pump with no auxiliary/backup heat (IH/IC heat pump),
....... HEATPUMP i
V
.@ i
- @ IO/B
-® I G
C co%_O%__'_ON
I
jooM_s_o_lI
ico._oR4 lc"_TA!_°_]
Z_ POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED
Z_ FACTORY INSTALLED JUMPER
Z_ MUST CONNECT THE 24 VAC COMMON WHEN USING L THE TERMINAL IS SHOWN AS EQUIPMENT MONITOR, CAN ALSO BE USED AS A 24 VAC
OUTPUT SEE "HEAT PUMP LED" SECTION FOR MORE INFORMATION
Z_ "O/B" TERMINAL SET TO CONTROL AS EITHER "O" OR "B" IN THE INSTALLER SETUP
Z_ OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR AVAILABLE ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE FROM THE
THERMOSTAT CABLE M19904
Fig. 19. Typical hookup of multistage heat pump with no auxiliary/backup heat (2H/20 heat pump).
9 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
....................HEATPUMP............
T
---i i
Z_I OUTDOORRNDOOR I--J i
TEMPERATURE --_
Al SENBOR[
o
@E!O/BI
®r-! y
®EIGI
EQUIPMENT
MONITOR
OPTIONAL 24 VAC
COMMON CONNECTION
Pv" s°wl_L_
{AUX'L'ARyHEAT2RELAY-HEAT)t[ E_SStOA¢_i J I
Z_ POWER SUPPLY PROVIDE D_SCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED
Z_ FACTORY INSTALLED JUMPER
Z_ OUTDOOR SENSOR REQUIRED IN SYSTEM WITH FOSSIL FUEL BACKUP HEAT THAT IS NOT USING AN EXTERNAL FOSSIL FUEL KIT
z_ OPTIONAL OUTDOOR OR iNDOOR REMOTE SENSOR AVAILABLE ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE
z_ MUST CONNECT THE 24 VAC COMMON WHEN USING L THE TERMINAL _S SHOWN AS EQUIPMENT MONfTOR, CAN ALSO BE USED AS
A 24 VAC OUTPUT SEE "HEAT PUMP LED" SECTION FOR MORE INFORMATION
z_ "O/B" TERMINAL SET TO CONTROL AS EITHER "O" OR "B" IN THE INSTALLER SETUP M19905
Fig. 20. Typical hookup of single-stage heat pump with auxiliary/backup heat (2H/1C heat pump).
......... HEATPUMP ........... EQUIPMENTMONITOR
OUTDOOR/INDOOR Ji
_HE_RE_Y! [
(AUXILIARY HEAT) EMERGENCY
HEAT RELAY
OPTIONAL 24 VAC
COMMON CONNECTION
ICH OVER!
COMPRESSOR4 lCOM_RE_
z_ POWER SUPPLY PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED
Z_ FACTORY INSTALLED JUMPER
z_ OUTDOOR SENSOR REQUIRED IN SYSTEM WITH FOSSIL FUEL BACKUP HEAT THAT IS NOT USING AN EXTERNAL FOSSIL FUEL KIT
Z_ OPTIONAL OUTDOOR OR INDOOR REMOTE SENSOR AVAILABLE ON SELECT MODELS WIRES MUST HAVE A CABLE SEPARATE
FROM THE THERMOSTAT CABLE
Z_ MUST CONNECT THE 24 VAC COMMON WHEN USING L THE TERMINAL IS SHOWN AS EQUIPMENT MONITOR, CAN ALSO BE USED AS
A 24 VAC OUTPUT SEE "HEAT PUMP LED" SECTION FOR MORE INFORMATION
z_ "O/B" TERMINAL SET TO CONTROL AS EITHER "O" OR "B" IN THE INSTALLER SETUP M19906
Fig. 21. Typical hookup of multistage heat pump with auxiliary/backup heat (3H/2C heat pump).
68-0280 10

VisionPRO TM 8000 Touchscreen Programmable Thermostat
POWERTHETHERMOSTAT
You can choose from three methods to power the thermostat:
• Batteries only (AAA alkaline).
• 24 Vac common wire only.
• 24 Vac common wire with battery backup (AAA alkaline).
Wiring 24Vac Common
• Single-Transformer System--Connect the common side of
the transformer to the C screw terminal of the thermostat
wallplate. Leave the metal jumper wire in place between
Rc and R.
• Two-Transformer System--Connect the common side of
the cooling transformer to the C screw terminal of the
thermostat wallplate. Remove the metal jumper wire
between Rc and R.
Installing Batteries
1. Install three AAA alkaline batteries on the back of the
thermostat as marked on the thermostat. See
Fig. 22.
I
M19918
Fig. 22. Installing batteries.
2. Locate and remove the tab labeled, Remove, in the
lower left corner on the thermostat back. See
Fig. 23.
TAB
M19920
Fig. 23. Remove tab labeled, Remove, on
thermostat back.
MountThermostat to Wallplate
1. Align the terminal screw blocks with the pins on the
back of the thermostat. Push the thermostat straight
onto the wallplate until it snaps into place. See Fig 24.
SCREW
BLOCK
ON
BACK OF
THERMOSTAT
M22213
Fig. 24. Mount thermostat to wallplate.
11 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
Locate and Mount C7089U Outdoor
Temperature Sensor(Optional)
Mount the sensor where (see Fig. 25):
cannot tamper with settings.
• there is good air circulation.
it can measure true outdoor ambient temperature.
surface is flat.
• wire distance between C7089 and thermostat is less than
200 feet.
Do not mount the sensor:
in direct sunlight.
• where hot or cold air blows on the sensor. Discharge line
from an outdoor compressor unit, vent or fan causes
inaccurate temperature readings.
• where snow, ice or debris can cover it.
Use the following steps to mount the sensor:
1. Remove the sensor from the mounting clip.
2. Mark the area on the location selected for mounting the
sensor mounting clip.
3. Mount the clip.
Fig. 25. Typical locations for C7089U Outdoor Sensor.
Wire C7089UOutdoorSensor
\CAUTION
Electrical Interference (Noise) Hazard.
Can cause erratic system operation.
Keep wiring at least one foot away from large inductive
loads such as motors, line starters, lighting ballasts
and large power distribution panels.
Use shielded cable to reduce interference when
rerouting is not possible.
IMPORTANT
Erratic temperature readings from a sensor can
occur as a result of any of the wiring practices
described below. Avoid these practices to assure
correct operation. Use shielded cable to reduce
interference if rerouting sensor wiring is not possible.
-- Be sure wires have a cable separate from the
thermostat cable.
-- Do not route temperature sensor wiring with building
power wiring, next to control contactors or near light
dimming circuits, electric motors or welding
equipment.
-- Avoid poor wiring connections.
-- Avoid intermittent or missing building earth ground.
CAUTION
Electrical Shock Hazard.
Can cause electrical shock or equipment damage.
Disconnect power supply before connecting wiring.
Wiring must comply with applicable codes, ordinances and
regulations:
1. Wire C7089 Outdoor Sensor to Sland S2 terminals on
the thermostat. If leadwire provided is not long enough
(60 in.), run a cable to a hole at C7089 location.
a. Using color-coded, 18-gauge thermostat wire is
recommended. For example of general wiring of
C7089, see Fig. 26.
b. Pigtail wiring can be used.
2. Mount C7089 in its mounting clip.
3. Plug wiring hole using nonhardening caulk or putty.
_ A _ WIRING HOLE
_"7,, A_Y_uCcUx_"RE
_USE APPROPRIATE MOUNTING MEANS FOR THE
Z_ TYPE OF STRUCTURE.
PLUG WIRING HOLE WITH NON-HARDENING CAULK
OR PUTTY. M19970
Fig. 26. Wire C7089 Outdoor Sensor to the thermostat.
68-0280 12

VisionPRO TM 8000 Touchscreen Programmable Thermostat
Locate and Mount C7189U Remote Indoor
Temperature Sensor(Optional)
1. Choose a location (see Fig. 27) for mounting the sensor
on an inside wall about 5 ft (1.5m) above the floor. A
vertically-mounted standard 2 x 4 in. (51 x 102 mm)
junction box can also be used.
2. Be sure wire distance between C7189 and thermostat is
less than 200 feet.
3. Make sure there is good air circulation at average
temperature at the chosen location. Avoid the following
locations because they can introduce errors in sensor
measurements. See Fig. 27.
a. Hot areas caused by:
(a) Concealed pipes or ducts.
(b) Drafts from fireplaces or other heat sources.
(c) Convection or radiant heat from the sun or
electrical equipment.
b. Cold areas caused by:
(a) Concealed pipes or ducts.
(b) Drafts from windows and doors.
(c) Unheated areas on the other side of the wall
location.
c. Dead air areas:
(a) Behind doors, furniture and curtains.
(b) In corners and alcoves.
4. Mark the area on the wall selected for mounting the
C7189 Sensor or junction box.
5. Run wire cable to a hole at the selected wall location.
Pull approximately three inches of wire through the
opening. Color-coded 18-gauge thermostat wire is
recommended.
Wire C7t89 IndoorSensor
CAUTION
Electrical Interference (Noise) Hazard.
Can cause erratic system operation.
Keep wiring at least one foot away from large inductive
loads such as motors, line starters, lighting ballasts
and large power distribution panels.
IMPORTANT
Erratic temperature readings from a sensor can
occur as a result of any of the wiring practices
described below. Avoid these practices to assure
correct operation.
-- Be sure wires have a cable separate from the
thermostat cable.
-- Do not route temperature sensor wiring with building
power wiring, next to control contactors or near light
dimming circuits, electric motors or welding
equipment.
-- Avoid poor wiring connections.
-- Avoid intermittent or missing building earth ground.
CAUTION
Electrical Shock Hazard.
Can cause electrical shock or equipment damage.
Disconnect power supply before connecting wiring.
Wiring must comply with applicable codes, ordinances and
regulations.
1. Wire C7189 Indoor Sensor to Sland $2 terminals on
the thermostat. For an example of general wiring of
C7189, see Fig. 28 to wire one sensor and 29 to wire
multiple sensors.
2. Push excess wire back into the hole. Plug the hole
using nonhardening caulk, putty or insulation to prevent
drafts from affecting performance.
3. Remove C7189 cover.
4. Mount C7189 to the wall or junction box using the
screws and anchors provided.
5. Level the C7189 for appearance only. Device functions
correctly even when not level.
6. install C7189 cover.
Fig. 27. Typical location for C7189 Indoor Sensor.
13 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
C7189 A
W
A POWER SUPPLY PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED
A IF MORE TIIAN ONE C7189 REMOTE SENSOR IS REQUIRED,
REFER TO FIGURE 3
A WIRES MUST HAVE A CABLE SEPARATE FROM THE
THERMOSTAT CABLE M19972
Fig. 28. Wiring asingle C7189 Indoor Sensor.
A, A
07189 07189
Y2
_I_2 A
A,
82 07189 07189 07189
C7189 C7189 C7189
C7189 C7189 C7189
A SENSORS MUSTBE ARRANGED IN THIS
CONFIGURATIONTO OPERATE CORRECTLY.
A WIRES MUST HAVE ACABLE SEPARATE FROM THE
THERMOSTAT CABLE. M19973
SetCalendar and Time
Thermostat keeps current time and day for up to ten years
under normal use after the calendar is set.
When the thermostat is first powered, the display is ready to
set the calendar and time.
NOTE: Calendar can also be set in the Installer Setup.
1. Press the arrow keys to set the year, month and day.
2. Press the Done key.
SET CURRENT DAY_
SET MONTH_ _,. B
/I ,c,4/
SE ARROWS TO SET YEAR AND TIME
M22424
3. Press the arrow keys to set the current time.
4. Press the Done Key.
M22425
Fig. 29. Wiring Multiple C7189 Sensors.
68-0280 14

VisionPRO TM 8000 Touchscreen Programmable Thermostat
INSTALLERSETUP
Follow these steps to enter the installer Setup:
1. Press and release the System Key.
3, Release the two blank keys when the screen on the
thermostat matches the screen below.
2.
/i Hu 1
M22426A
Press and hold the two blank keys on either side of the
center blank key for approximately five seconds until
screen changes.
M19923
4. See screen below to review how the thermostat keys
are used during Installer Setup. See Tables 3-5 for the
installer Setup Numbers and Settings.
F- ADVANCE TO NEXT
sNESuT_pLLER _ /INST#rLLLcEuRRSETUTP
iNSTALLER SETUP CURRENT
SETTING M22443
5. Press the Done key to exit the installer Setup screen.
15 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
Table 3. Installer Setup Menu.
Installer Setup
Number Installer Setup Name Notes
0120 Date (Year Upper) 2001 - 2178 available
0130 Date (Year Lower) 2001 - 2178 available
0140 Date (Month)
0150 Date (Day)
0160 Schedule Options
0170 System Type Selection
Settings
Select first two digits of current calendar year (2005, etc)
Select last two digits of current calendar year (05 for year
2005, etc)
Select number that represents current calendar month
Select number that represents current calendar date
0--nonprogrammable
4--7-day programmable
1--1 heattl cool conventional (factory setting)
2--single-stage heat pump (no auxiliary heat)
3--heat only conventional (no fan) Also for 750mV.
4--heat only conventional (with fan)
5--heat only (power to open and power to close zone
valves or normally-open zone valves)
6--cool only conventional
7--2 heat/1 cool heat pump (with auxiliary heat)
8--2 heatt2 cool multistage conventional
9--2 heattl cool multistage conventional
10--1 heat/2 cool multistage conventional
11--2 heatt2cool heat pump (no auxiliary heat)
12--3 heat/2cool heat pump (with auxiliary heat)
0--gas or oil furnace equipment controls fan in heating
(factory setting)
l--electric furnace--thermostat controls fan in heating
Available options and
defaults vary by
thermostat. System
selection automatically
modifies some default
Cycles per hour (cph) for
1st Stage Compressor
Cycles per hour (cph) for
2nd Stage Compressor
Cycles per hour (cph) for
1st Stage Conventional
Heat
settings and/or hides
other installer Setup
options.
0180 Fan Control in Heating Only shown if
conventional system is
selected. If heat pump is
chosen, fan defaults to
electric.
0190 Changeover Valve--O/B Only shown if heat pump
Terminal Energized in system is chosen.
Heating or Cooling
(Heat Pumps Only)
0200 Backup Heat Source Only shown if 2 heat/
(Auxiliary Heat) 1 cool or 3 heat/2 cool
heat pump is chosen
0210 External Fuel Fossil Only shown if fossil fuel is
Fuel Kit chosen as backup heat
source.
0220
0230 Only shown if two stages
of cool are selected.
0240 Not shown if system
selection is heat pump.
0--changeover valve--O/B terminal is energized in
cooling (factory setting)
1--changeover valve--OIB terminal is energized in
heating
0--heat pump backup heat source is electric (factory
setting)
l--heat pump backup heat source is fossil fuel
0--no external fossil fuel kit is controlling heat pump
backup heat. This thermostat controls the dual fuel. Must
install outdoor sensor and set Installer Setup Number
0340 to number 2.
1--external fossil fuel kit is controlling heat pump backup
heat
3--cph recommended for compressors (factory setting)
1, 2, 4, 5, 6--other cycle rate settings
3--cph recommended for compressors (factory setting)
1, 2, 4, 5, 6--other cycle rate settings
1-- 1 cph used for steam and gravity
3--3 cph used for hot water system and high efficiency
(90% or better) furnaces
5--5 cph used for standard fossil fuel forced air (less than
80% efficient) systems (factory setting)
9--9 cph used for electric furnaces
2, 4, 6, 7, 8, 10, 11, 12--other cycle rate settings
1--1 cph used for steam and gravity
3--3 cph for hot water systems and high efficiency (90%
or better) furnaces
5--5 cph for standard fossil fuel forced air (less than 90%
efficient) systems (factory setting)
9--9 cph used for electric furnaces or electric auxiliary
heat for heat pump systems
2, 4, 6, 7, 8, 10, 11, 12--other cycle rate settings
Cycles per hour (cph) for
2nd Stage Heat (Aux
Heat for 2H/1C Heat
Pumps)
Selection in this stage
changes default cph for
2nd stage heat.
Only shown if two stages
of heat are selected.
0250
68-0280 16

VisionPRO TM 8000 Touchscreen Programmable Thermostat
Table 3. Installer Setup Menu. (Continued)
Installer Setup
Number
0260
O27O
Installer Setup Name
Cycles per hour (cph) for
3rd Stage Heat
(Aux Heat for 3H/2C
Heat Pumps)
Cycles per hour (cph) for
Em Heat
Settings
1--1 cph used for steam and gravity
3--3 cph for hot water systems and high efficiency (90%
or better) furnaces
5--5 cph for standard fossil fuel forced air (less than 90%
efficient) systems (factory setting)
9--9 cph used for electric furnaces or electric auxiliary
heat for heat pump systems
2, 4, 6, 7, 8, 10, 11, 12--other cycle rate settings
3--3 cph for hot water systems and high efficiency (90%
or better) furnaces
5--5 cph for standard fossil fuel forced air (less than 90%
efficient or better) systems
9--9 cph for electric strip heat for heat pumps
0--Backlight not on continuously. Thermostat backlight
comes on with each key press.
l--Backlight is on continuously (thermostat must have a
common wire attached for this function).
Notes
Only shown if 3H/2C
heat pump is selected.
Only shown if 2H/1C or
3H/2C heat pump is
selected.
0280 Continuous Backlight Option is always shown;
however, continuously on
backlight works only if
thermostat is wired with
24 Vac Common.
0300 Changeover
0310 Deadband Shown only if automatic
changeover is selected.
0--manual changeover (factory setting)
l--auto changeover
Heating and cooling setpoints can be set no closer than
chosen value:
2--2°F (1.5°C)
3--3°F (2°C)
4--4°F (2.5°C)
5--5°F (3°C)
6--6°F (3.5°C)
7--7°F (4°C)
8--8°F (4.5°C)
9--9°F (5°C)
0--fahrenheit temperature display (factory setting)
l--celsius temperature display
0320 Temperature Indication
Scale
0330 Daylight Savings 1--daylight savings is on (factory setting).
0--daylight savings is off.
0340
0350
0--no remote temperature sensor
l--outdoor temperature sensor for displayonly.
2--outdoor temperature sensor for control. Outdoor
sensor used for Heat Pump Lockout settings. (See Heat
Pump Temperature Lockout section for more details.)
3--indoor temperature sensor
0--no compressor lockout.
Remote Temperature
Sensor (Outdoor or
Indoor)
Heat Pump Compressor
Set to 0 in areas that do
not follow daylight
savings.
Defaults and Options
depend on System Type
selection.
indoor Temperature
Sensor uses an averaging
network and does not
include on-board sensor.
Default depends on other
Lockout or (Balance
Point) 15°F(-9.5°C)
20°F (-6.5°C)
25°F (-4°C)
30°F (-1 °C)
35°F (1.5°C)
40°F (4.5°C)
45°F (7°C)
selections. Shown if
Outdoor Temperature for
control is selected. (See
Advanced Features
section for more
information.)
17 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
Table 3. Installer Setup Menu. (Continued)
Installer Setup
Number
0360
O38O
0500
0510
0520
0530
0540
Installer Setup Name
Heat Pump Auxiliary
Lockout
Indoor Dehumidification
Control
Furnace Change
Reminder
Humidifier Pad
Replacement Reminder
UV Lamp Replacement
Reminder
Adaptive Intelligent
Recovery TM
Number of Periods
Settings
0--no auxiliary heat lockout.
40°F (4.5°C)
45°F (7°C)
50°F (10°C)
55°F (13°C)
60°F (15.5°C)
0--No indoor dehumidification control.
l--Dehumidification control activated.
0--furnace filter reminder off
1--10 run time days
2--30 run time days
3--60 run time days
4--90 run time days
5--120 run time days
6--365 run time days
0--humidifier pad replacement reminder off
1--90 calendar days
2--180 calendar days
3--365 calendar days
0--UV lamp replacement reminder off
1--365 calendar days
lmAdaptive Intelligent Recovery TM control is activated
(system starts early so setpoint is reached by start of
program period).
0--Conventional Recovery (system starts recovery at
programmed time)
2--two periods available (Wake and Sleep)
4 four periods available (Wake, Leave, Return and
Sleep)
Notes
Shown if electric is
chosen for backup heat
source and outdoor
temperature sensor for
control is selected. (See
Advanced Features
section for more
information.)
Available on select
models.
If dehumidification control
is activated and auto-
changeover is selected in
Installer Setup Number
0300, the deadband
minimum is defaulted to
5°F (3°C) in Number
0310.
Run time based on call for
fan.
Not shown if non-
programmable is
selected. 2 or 4 applies to
all days of the week.
0580 Minimum Compressor 5--five-minute compressor off-time setting (factory --
Off Time setting)
0, 2, 3, 4--other compressor off-time settings
0600 Heat Temperature 40-90--temperature range (1 °F increments) of heating Shown in 1t2 °C.
Range Stop setpoint.
0610 Cool Temperature 50-99--temperature range (I°F increments) of cooling Shown in 1/2 °C.
Range Stop setpoint.
0640 Clock Format 12--12 hour clock (factory setting)
24--24 hour clock
68-0280 18

VisionPRO TM 8000 Touchscreen Programmable Thermostat
Table 3. Installer Setup Menu. (Continued)
Installer Setup
Number Installer Setup Name Settings Notes
0650 Extended Fan OnTime 0--no extended fan operation after call for heat ends Not shown iffan operation
Heat 90-- fan operation is extended 90 seconds after call for is set to fossil fuel or in
heat ends. Cool Only Systems
0660 Extended Fan On Time 0--no extended fan operation after call for cool ends Not shown in Heat Only
Cool 90--fan operation is extended 90 seconds after call for Systems.
cool ends.
0670 Keypad Lockout
0680
0690
O7OO
0--unlocked keypad
l--partially locked keypad
2--fully locked keypad
Temperature Control in
Heat
Temperature Control in
Cool
Temperature Display
Offset
l--less aggressive temperature control (could cause
temperature undershoot)
2--Standard temperature control in heating (factory
setting)
3--more aggressive temperature control (could cause
temperature overshoot)
l--less aggressive temperature control (could cause
temperature undershoot)
2--Standard temperature control in cooling
(factory setting)
3--more aggressive temperature control (could cause
temperature overshoot)
-3 --°F (-1.5°C)
-2 --°F (-1°C)
-1 --°F (-.5°C)
0 --°F (0. °C) -- (no difference in displayed temperature
and actual room temperature )
I --°F (.5°C)
2--°F (1°C
3 --°F (1.5°C)
Unlocked--all functions
are available.
Partially locked--only
temperature up and down
keys and ability to enter
and modify Installer Setup
mode are available.
Fully locked--only ability
to enter and modify
installer Setup mode are
available.
Applies to recovery ramp
and use of auxiliary heat
during recovery.
Choose 1 if getting
temperature overshoot.
Choose 3 if getting
temperature undershoot.
Applies to recovery ramp.
Choose 1 if getting
temperature overshoot.
Choose 3 if getting
temperature undershoot.
0710 Reset Thermostat 0--no thermostat reset. Only calendar settings
l--resets all Installer Setup Options to default values and and time are retained.
resets schedule to default setting.
19 68-0280

VisionPRO TM 8000 Touchscreen Programmable Thermostat
INSTALLERSYSTEMTEST
Use the Installer System Test to test the heating, cooling and
fan (and emergency heat for heat pump systems).
\CAUTION
Equipment Damage Hazard.
Minimum compressor off time is bypassed during
Installer System Test
Avoid cycling compressor quickly.
Howto Usethe InstallerSystemTest
The installer Test is part of the Installer Setup Menu.
1. Enter the Installer System Test by entering the installer
Setup.
2. Note that the test appears at the end of the Installer
Setup Numbers.
3. See Fig. 30 to review how the thermostat buttons are
used during the installer System Test. See Table 6 for
available Installer System Tests.
NUMBER -SYSTEM STATUS -UP ARROW
NUMBER TURNS THE
SYSTEM ON
DONE KEY- UP ARROW
EXFSINSTALLER ADVANCES TO
SYSTEM TEST NEXT SYSTEM
TESTNUMBER
DOWN ARROW
TURNS THE
SYSTEM OFF M22428
Fig. 30. Review thermostat buttons used during Installer
System Test.
Installer System Tests
IMPORTANT
Use the Installer System Test to test the heating, cooling, fan and emergency heat. The setting you choose for System
Type (Installer Setup Number 0170) may prevent some System Test Numbers from appearing.
Table 4. Installer System Test.
System Test Number Test Type System Status Number and Description
Test ICooling System Test 1--Cool stage 1 turns on.
2--Cool stage 1 and stage 2 turn on.
0--Cool is off.
Test 2 Fan System Test 1--Fan turns on.
0--Fan turns off.
Test 3 Heating System Test 1--Heat stage 1 turns on.
2--Heat stage 1 and stage 2 (aux heat) turn
on.
0--Heat is off.
Test 4 Emergency Heat Test 1--Emergency heat turns on.
2--Emergency heat and auxiliary heat turn on.
0--Emergency heat turns off.
Press the Next button to go to the beginning of the Installer Setup or press the Done button to exit the Installer
System Test.
68-0280 20