Honeywell Wi-Fi VisionPRO8000 User manual

Wi-Fi VisionPRO®8000
Installation Guide
Current display. Underlined label
signifies the current display.
Mode control buttons. Use to change
settings for Fan or System Heat/Cool.
Menu. Select options to: set schedules,
view equipment status, change IAQ
settings, access installer options*, etc.
Current status. Shows system mode
(heat/cool), outdoor temperature and
humidity.
Current schedule. Shows desired
temperature and schedule status.
Indoor conditions. Shows indoor
temperature and humidity.
Current Time.
Alert Light. On when alert
message is active or system is set to
Em Heat.
Reference to key features
* Password is the date code.

2
1 Separate wallplate from thermostat.
Press button on top and pull to remove
the wallplate.
2 Mount wallplate as shown.
Mount new wallplate using screws
and anchors included with the
thermostat.
Drill 3/16-in holes for drywall.
Drill 7/32-in holes for plaster.
Wallplate
(back view)
Wallplate
S1
S1
W
Y
G
W2
Y2
A
C
K
R
C
R
U1
U1
U2
U2
S1
S1
O/B
Y
G
AUX
-E
Y2
L/A
Thermostat
Button
Getting started
Follow these basic steps to install this thermostat,
set installer options, and connect to the Wi-Fi
network.
Installing the thermostat
Residential/Résidentiel 1-800-468-1502 http://yourhome.honeywell.com Commercial/Commerciale 1-888-245-1051 http://customer.honeywell.com Honeywell, Golden Valley, MN 55422
RoHs Compliant
Conformité RoHs
Assembled in Mexico
Assemblé au Mexique
TH8321WF1001
1
1524
M35344
1-855-733-5465 http://yourhome.honeywell.com Honeywell, Golden
Valley, MN 55422
RoHs Compliant
Conformité RoHs
Assembled in Mexico
Assemblé au Mexique
TH8321WF1001
1
1524
M35343
Thermostat (back view)
Password
(Date Code)

3
3 Connect power.
24VAC power is required. Connect
common side of transformer to C
terminal.
S1
S1
W
Y
G
W2
Y2
A
S1
S1
O/B
Y
G
AUX
-E
Y2
L/A
K
RC
R
U1
U1
U2
U2
C
CONVENTIONAL
HEAT PUMP
4 Wire the thermostat.
Refer to the table and wiring
diagrams on the next page.
a Turn on 24VAC NOW.
24VAC (C wire) is required.
S1
S1
W
Y
G
W2
Y2
A
S1
S1
O/B
Y
G
AUX
-E
Y2
L/A
K
RC
R
U1
U1
U2
U2
C
CONVENTIONAL
HEAT PUMP
5 Mount thermostat on wallplate.
Align thermostat at bottom and
snap into place as shown.
Thermostat
Wallplate

4
Terminal Designations
Conventional System Heat Pump
Terminal Description Terminal Description
CCommon wire from secondary side of
cooling transformer (if 2 transformers). CCommon wire from secondary side of
cooling transformer.
Rc* Cooling power. Rc Cooling power.
R* Heating power. R Heating power.
W Heat Stage 1 O/B Changeover valve for heat pumps.
W2 Heat Stage 2 AUX-E Backup Heat/Emergency Heat
Y Compressor Stage 1 Y Compressor Stage 1
Y2 Compressor Stage 2 Y2 Compressor Stage 2
G Fan Relay G Fan Relay
AConnect to Economizer Module or
Lighting Panel (TOD). L/A Connect to Compressor Monitor, Zone
Panel, Economizer Module or Lighting
Panel (TOD).
U1 / U1 Universal relay for humidification, dehumidification, ventilation, or a stage of
heating/cooling. U1 / U1 Universal relay for humidification,
dehumidification, ventilation, or a stage of
heating/cooling.
S1 / S1 Universal input for a wired indoor, outdoor
or discharge sensor. S1 / S1 Universal input for a wired indoor, outdoor
or discharge sensor.
K** Connect to K on Wire Saver module. K** Connect to K on Wire Saver module.
* Remove factory installed jumper for two transformer systems.
** The THP9045A1023 Wire Saver module is used on heat/cool systems when you only have four wires at the thermostat and you
need a fifth wire for a common wire. Use the K terminal in place of the Y and G terminals on conventional or heat pump systems to
provide control of the fan and the compressor through a single wire—the unused wire then becomes your common wire. See THP9045
instructions for more information.
C
K
RC
R
U1
U1
120
VAC
24
VAC
C
R
SYSTEM
TRANSFORMER
120
VAC
24
VAC
HUM, DEHUM OR
VENT
TRANSFORMER
THERMOSTAT
POWERED
HUMIDIFIER,
DEHUMIDIFIER
OR VENTILATOR
C
K
RC
R
U1
U1
120
VAC
24
VAC
C
R
SYSTEM
TRANSFORMER
THERMOSTAT
NON-POWERED
HUMIDIFIER,
DEHUMIDIFIER
OR VENTILATOR
FIELD INSTALL JUMPER
BETWEEN R AND U1
CONNECTING A HEAT OR COOL STAGE TO U1DEHUMIDIFICATION WITH LOW SPEED FAN
NON-POWERED HUMIDIFIER, DEHUMIDIFIER OR VENTILATORPOWERED HUMIDIFIER, DEHUMIDIFIER OR VENTILATOR
Wire the thermostat universal relay to the low speed fan
for dehumidication control at the equipment. The
thermostat relay can be set to normally open or
normally closed in the thermostat installer setup.
1
U1 terminals are normally open dry contacts when set
up for a stage of heating or cooling.
You must install a eld jumper if the stage of heating
or cooling is powered by system transformer. Do NOT
install a eld jumper if the stage of heating has its own
transformer.
1
2
Normally open, dry contacts
Normally closed, dry contacts
1
C
K
RC
R
U1
U1
120
VAC
24
VAC
C
R
SYSTEM
TRANSFORMER
THERMOSTAT
DEHUMIDIFICATION
WITH LOW SPEED FAN
FIELD INSTALL JUMPER
BETWEEN R AND U1
OR
2
C
K
RC
R
U1
U1
120
VAC
24
VAC
C
R
TRANSFORMER
THERMOSTAT
HEAT STAGE 3, COOL
STAGE 3, BACKUP HEAT
STAGE 2 FOR HEAT
PUMPS, OR GEOTHERMAL
RADIANT HEAT
1

5
Setup options define the type of system you are installing and preferences for the
display.
1 Follow prompts on the screen to select the appropriate options. Among the
screens you might see wil be options for:
1.1 Application, either Residential or
Commercial.
1.2 Thermostat Name, which will enable
you to identify it if you’re installing more
than one thermostat (for a zoned HVAC
application, for instance).
1.3 Thermostat Type, either programmable
or not, depending on preference.
1.4 Temperature scale, either Fahrenheit or
Celsius.
1.5 Any Outdoor Air Sensors installed.
NOTE: If you are using a Wired Outdoor
Sensor or the outdoor temperature from the
Wi-Fi connection to lockout the compressor
or Auxiliary heat, select Yes to see the
installer options for lockout temperatures.
1.6 The type of heating system.
1.7 For all installer options, press the sor
tbuttons to change the option.
1.8 Press Next to move to the next setting, and Done when setup is complete.
Performing installer setup
APPLICATION
residential
M34150
THERMOSTAT TYPE
programmable
M35356
THERMOSTAT NAME
THERMOSTAT
M35357
TEMPERATURE SCALE
fahrenheit
M35358
OUTDOOR AIR
SENSOR: no
M35359
HEATING SYSTEM
conv. forced air

6
After installer setup, you will be prompted to connect to a Wi-Fi network.
NOTE: If you select No, the homeowner
can connect to the Wi-Fi network later. (See
“Connecting to Wi-Fi later” on page 8
or in the User’s Guide.) The thermostat will
display its Home screen and thermostat
setup is complete.
1 Connect to the Wi-Fi network now.
1.1 Press Yes.
The thermostat will scan for available
Wi-Fi networks.
1.2 Use the arrow buttons to scroll up/
down or left/right. Press the Wi-Fi
network name, then press Select.
NOTE: If the Wi-Fi network name is hidden,
see “Connecting to a hidden Wi-Fi network”
on page 10.
1.3 When prompted, press the screen to
edit the password (if necessary).
1.4 Enter the password.
Press the sor t buttons to change
the letter or number.
Press the button to move to the next
character, or the button to move to
the previous character.
Use the sor t buttons at the bottom
to change letter case.
Press Done when complete.
1.5 The screen will let you know when the
connection is successful. Press Done
when the connection is successful.
If the connection is not successful,
the screen will explain why not. See
“Unsuccessful connection” on page
9. Follow instructions on the screen
to try again.
NOTE: Press the Help button for more
information about an unsuccessful connection.
Connecting to Wi-Fi
M35345
Connect to a
Wi-Fi network now?
M35346
Delete Space
AC
M35347
Select Wi-Fi Network
Your Network
M35349
Finding Networks
Please Wait
M35350
Enter Password
Press Here to Edit
M35351
Connection
Successful
M35360

7
2 The homeowner must have a Total Connect Comfort account.
2.1 Have the homeowner go to
www.mytotalconnectcomfort.com and
follow the instructions to login or create
an account.
2.2 Press the t button to display Wi-Fi
signal strength, status, IP address, MAC and CRC.
2.3 Note the Thermostat MAC and CRC; they will be needed during registration.
Or, refer to the User’s Guide.
M35361
Register at:
• To make changes to Installer Setup
• To perform an Installer Test
Finding the password
You can find the date code
on the back of the thermostat,
or touch Menu, select Dealer Information,
and scroll to the bottom to see Date Code.
1 Touch Menu.
2 Select Dealer Information.
3 Scroll down to see the Date Code.
MCR35348
TH8321WF1001
Date Code: 1524
MCR34022
Dealer Information
Installer Options
Finding the password (Date Code)
Residential/Résidentiel 1-800-468-1502 http://yourhome.honeywell.com Commercial/Commerciale 1-888-245-1051 http://customer.honeywell.com Honeywell, Golden Valley, MN 55422
RoHs Compliant
Conformité RoHs
Assembled in Mexico
Assemblé au Mexique
TH8321WF1001
1
1524
M35344
1-855-733-5465 http://yourhome.honeywell.com Honeywell, Golden
Valley, MN 55422
RoHs Compliant
Conformité RoHs
Assembled in Mexico
Assemblé au Mexique
TH8321WF1001
1
1524
M35343
Thermostat (back view)
Password
(Date Code)

8
Making changes to Installer Setup and performing an Installer Test
1 Touch Menu.
2 Select Installer Options.
3 Enter password (date code) and
touch Done. See “Finding the password” on
page 7 to find the date code.
4 Select Installer Setup or Installer Test.
5 Follow prompts on the screen to select
the desired setup options or to perform an
equipment test.
MCR33977
Enter password
0 0 0 0
MCR33976
Installer Options
MCR34015
Installer Setup
Installer Test
Checking signal strength
After you successfully connect to the Wi-Fi
network (see “Connecting to Wi-Fi” step 1.5),
the thermostat will display signal strength. The
signal strength symbols have the following
meanings:
Signal strength is 75%–100%
Signal strength is 50%–75%
Signal strength is 0%–50%
You can also check signal strength at any time after the thermostat is connected to the
Wi-Fi network by pressing MENU then Wi-Fi Setup.
Connecting to Wi-Fi later
1 Press MENU, then Wi-Fi Setup.
2 Follow the prompts on-screen (and in
“Connecting to Wi-Fi”) to select the Wi-Fi
network and enter the password.
NOTE: To view and set the Wi-Fi thermostat
remotely, the homeowner must have a Total
Connect Comfort account. See “Connecting
to Wi-Fi” step 2.
M35365
Wi-Fi Network:
YourNetwork
DoaIol Inrol Madorl
Wi-Fi Setup
Installer Options
M35352

9
Unsuccessful connection
If you are unsuccessful in connecting the thermostat to the Wi-Fi network, you will
see a Connection Failed screen. Press the t button for other tips about this failed
connection. Here are three specific reasons the connection might be unsuccessful.
For all Connection Failed screens, pressing Done will return to the Menu screen.
Invalid Password
The password you entered is invalid. Check that
you have the right password and try again.
Press Back to return to “Connecting to Wi-Fi”
step 1.3 on page 6.
No IP Address
The thermostat was unable to obtain an IP
address from the router. Verify the router is
correctly set up to automatically assign IP
addresses. This connection can take several
minutes. If there is still no connection, remove
the thermostat from the wallplate for 10 seconds,
then snap it back into place.
No Internet Link
The thermostat connected to the Wi-Fi network
but was unable to establish a connection to the
internet. Check the router settings and try again.
Make sure the Ethernet cable is plugged into the
router and try rebooting the router if necessary.
M35362
Connection Failed
Invalid Password
M35363
Connection Failed
No IP Address
M35364
Connection Failed
No Internet Link

10
If the Wi-Fi network name is hidden and it doesn’t show up in the list in “Connecting to
Wi-Fi” follow these steps to connect to it.
1 Press MENU, then Wi-Fi Setup.
2 Press Other, then press Select.
3 When prompted, press the screen to edit the
network name.
4 Enter the network name.
Press the sor t buttons to change the letter
or number.
Press the button to move to the next
character, or the button to move to the
previous character.
Use the sor t buttons at the bottom to
change letter case.
Press Done when complete.
5 Select the appropriate network security setting,
then press Select.
6 Enter the Wi-Fi network password as shown in
“Connecting to Wi-Fi” step 1.4.
Connecting to a hidden Wi-Fi network
M35346
Delete Space
AC
DoaIol Inrol Madorl
Wi-Fi Setup
Installer Options
M35352
M35353
WirelessNetwork
Other...
M35354
Enter Network Name
Press Here to Edit
M35355
SSID Security
Open Network