HOTATA 3106 User manual

User Manual
Model No: 3106
IMPORTANT: Read the instructions carefully before
operating the appliance and keep them for future reference.
Version 1.0

Email US: [e-mail]
Check out our video tutorials available at
https://www.youtube.com/
@hotataaftersale/playlists
Scan QR code for
video tutorials
Customer Service
1 Year Warranty Lifetime Customer Support
Quality Assurance Support Return and Exchange
[e-mail]

1
Contents
Components List 2
Installation Guide
Programming Guide
Factory Default Reset
Change Programming Code
Advanced Stting Options
System Alerts
FCC Warning
3
8
9
10
11
12
13
Template 14
[e-mail]

Keypad Assembly
Deadbolt Strike Plate
Battery Cover
Key ①
③
③
④
⑤
②
3/4"(19mm)Screws-4 pcs
3/4"(19mm)Screws-2 pcs
1-5/32"(33mm)Screws-2 pcs
①
②
③
④ ⑤
Optional Reinforcement
screws (1 set)
Components List
Deadbolt Latch Mounting Plate Interior Assembly
Entry Key
(2 ea.)
Interior Assembly Mounting Plate Deadbolt Strike Plate
Keypad Assembly Deadbolt Latch
Tools Required
Tools Required for Installation on Pre-drilled Doors:
·Phillips Screwdriver (DO NOT USE POWER DRILL!)
[e-mail]

Prepare the door and check dimensions
(60 or 70mm)
1"
25mm
Installation Guide
If drilling a new door, use the supplied template and the complete door drilling
instructions.
Optional:For the best fix, you may need to drill an additional hole for the reinforcement
screw.
1.Measure to confirm that the hole in the
door is 2-1/8"（54mm)
2.Measure to confirm that the backset is
either 2-3/8"or 2-3/4"(60 or 70mm)
3.Measure to confirm that the hole in the
door edge is 1"(25mm)
4.Measure to confirm the thickness of the
door is between 1-3/8"and 2"(35 and
50mm)
2-1/8"
54mm
2-3/8" or 2-3/4"
(35 and 50mm)
1-3/8" and 2"
[e-mail]

Install the latch and strike
up
up
up
up
up
Installation Guide
No adjustment is required.
Proceed to next step.
Twist the latch and adjust
the bolt length.
(As shown below)
Make sure the hole in the door frame is
drilled a minimum of 1"(25mm) deep.
1.Insert the latch bolt into the door.
Actural Size
3/4"(19mm)Screws-2 ea.
Make sure the +-shaped hole is
in the bottom position
YES NO
2-3/4"70mm
YES NO NO
2.Install strike on the door frame.
Actural Size
3/4"(19mm)Screws-2 ea.
[e-mail]

Locking lever
transversal through
the latch
Install the exterior assembly
Installation Guide
Route the cable through the
do or be low the bolt and
push the keypad onto the
door.
The key must be pulled out when
installing.
cable
YES NO
[e-mail]

Install the interior assembly
Installation Guide
1.Please confirm the door opening direction before installing.
Find the direction switch under the Interior Assembly, and change the direction as per
the instructions below
2.Route cable through the bottom of
mounting plate.
3.Tighten screws evenly.
Note:please support
e x t e r i o r a s s e m b l y
d u r i n g m o u n t i n g
plate installation
Insert key and test latch.if latch does not
extend or retract smoothly. please
adjust mounting plate screws.
If the keypad and mounting plate are deflection.
please loose mounting plate screws and adjust.
Switch to the left Switch to the right
Left opening door Right opening door
LR
4.Ensure tight cable connection.5.Tighten screws evenly.
YESYES NO NO
[e-mail]

① Press and hold , the latch bolt extends by itself.
② Enter preset code: 1234, press , the latch bolt retracts by itself.
！
Install the batteries and test the lock
Installation Guide
Note: Do not use rechargeable batteries or Non-alkaline batteries.
1.Install 4 AA batteries in battery pack.
①Push up to
re m o v e th e
battery cover
②Install 4 AA
ba t t er i e s i n
battery pack.
③Push do wn
t o c l o s e t h e
battery cover.
2.Test the lock.
If the latch bolt doesn't extend or retract smoothly,please check the direction switch
or re-install the lock.Green lights means successfully installed.Red lights means
unsuccessfully installed.
Successful Unsuccessful
Green Red
[e-mail]

！
Type-C emergency power port
Programming Guide
Programming Symbols
Factory default settings
PC
UC
ID
Lock
Unlock / Programming
Programming Code
User Code (4-8Digits)
User ID (01-50) 2Digits
The lock is in experience mode
PC
UC
ID
SET
Programming Code: 123456
User Code: 1234 or any 4-8Digits
Indoor unlock / lock button
Reset button
[e-mail]

Factory Default Reset
！
A factory reset will delete all codes associated with the lock.
Find a paper clip, put it into the hole at the bottom,
long press for 5 seconds, until the buzzer beeps.
Find a paper clip, put it into the hole at the bottom, long press for 5 seconds,
until the buzzer beeps.
SET
[e-mail]

Preset code
Enter new programing code Reenter new programing code
Change Programming Code
！
1.For your safety, it is strongly recommended that you change and remember your
programming code in time.
2.When you enter the wrong button, the system will exit the programming mode, and
you can attempt programming procedure again.
3.If you do not enter any buttons within 5 seconds, the system will exit the programming
mode, and you can attempt programming procedure again.
If your lock is new, the factory preset code is: 123456
The new programming code must be 6 digits
If the operation is successful:the green light and beeps 1 second.
If the operation is wrong:the red light flashes 3 times with 3 beeps.
If you do not enter any buttons within 5 seconds:the red light flashes 3 times with 3
beeps,system will exit the programming mode.
！
Important tips for programming：
PC 4
PC PC
Programming Symbols Factory default settings
PC
UC
ID
PC
UC
ID
SET
Lock
Unlock / Programming
Programming Code
User Code (4-8Digits)
User ID (01-50) 2Digits
The lock is in experience mode
Programming Code:123456
User Code: 1234 or any 4-8Digits
Indoor unlock / lock button
Reset button
10 [e-mail]

3
Programing code
Programing code
Enter new user code Reenter new user code
Add new user code
Advanced Stting Options
！
！
If the operation is successful:the green light and beeps 1 second.
If the operation is wrong:the red light flashes 3 times with 3 beeps.
If you do not enter any buttons within 5 seconds:the red light flashes 3 times with 3
beeps,system will exit the programming mode.
NEW PC the code must be 4-8 digits 01-50 digits ID
PC 1
2digits
ID UC UC
Delete User code
After deletion, the user code will not be able to unlock
for an existing user
ID
PC
ID
2digits
11 [e-mail]

System Alerts
the red light flashes 3 times
with 3 beeps
Door jammed while
attemptiong to lock/Unlock
Unsuccessful programming
Incorrect User Code ente
Manually re-lock, check
and reinstall if necessary
Attempt programming
procedure again
Re-enter User Code
The red light and beep 1
second repeat 3 times after
each unlock
Low battery
Replacement battery
Super low battery
Us e Typ e - C e m e r ge n c y
power supply to unlock or
key to unlock then replace
battery
Battery run out
Bad cable connection
The red light and beep 1
second after press unlock
button. And can not unlock
The keypad and lightindicator
no respond
Re-connect the cable
lf you have any questions, please contact us at any time.
Email: Aftersale @hotata.com
Alert Reason Solution
12 [e-mail]

FCC Warning
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
13 [e-mail]

FOLD HERE ON
DOOR EDGE MARK CENTER
OF HOLE ON
DOOR FACE
DRILL
2-1/8"(54mm)
HOLE
MARK
FOR 1-3/4"
(45mm)
DOOR
THEN DRILL 1" (25mm) HOLE
IN CENTER DOOR OF EDGE
2" (50mm) IN DEPTH
MARK
FOR 1-3/8"
(35mm)
DOOR
1
3
4
6
5
TEMPLATE
TEMPLATE
2
14 [e-mail]

Scan the QR code or visit the link:
https://www.youtube.com/@hotataaftersale/playlists
to watch video tutorials, which can help you better understand the installation
and usage of the product.
Scan QR code for
video tutorials
[e-mail]