EN
7
• Tap “Your Meal Times”.
• Scroll through the list and tap the relevant time.
• Tap the relevant meal to change it.
It will be possible to combine a time slot only with a meal.
10. TOOLS
Press to open the “Tools” menu at any time. This
menu enables you to choose from several options
and also change the settings or preferences for your
product or the display.
REMOTE ENABLE
To enable use of the Hotpoint-Ariston Home Net app.
KITCHEN TIMER
This function can be activated either when using a
cooking function or alone for keeping time. Once
started, the timer will continue to count down
independently without interfering with the function
itself. Once the timer has been activated, you can also
select and activate a function.
The timer will continue counting down at the top-right corner
of the screen.
To retrieve or changhe the kitchen timer:
• Press .
• Tap .
An audible signal will sound and the display will
indicate once the timer has finished counting down
the selected time.
• Tap “DISMISS” to cancel the timer or set a new
timer duration.
• Tap “SET NEW TIMER” to set the timer again.
LIGHT
To switch on or off the oven lamp.
SELFCLEAN
Activate the “Self-Clean” function for optimum
cleaning of the internal surfaces.
It is reccommended to do not open the oven door during the
cleaning cycle to avoid a loss of water vapor that could get an
adverse eect on the nal cleaning result.
• Remove all accessories from the oven before
activating the function.
• When the oven is cold, pour 200 ml of drinking
water on the bottom of the oven.
• Tap “START” to activate the cleaning function.
Once the cycle has been selected, you can delay the start of
automatic cleaning. Tap “DELAY” to set the end time as
indicated in the relevant section.
DRAIN
The drain function allows the water to be drained in
order to prevent stagnation in the tank. For optimal
use of the appliance, it is advisable to always carry
out draining everytime the oven has been used with
a steam cycle.
Once selected the “Drain” function, follow the actions
indicated: Open the door and place a large jug
under the drain nozzle located at the bottom right
of the panel. Once started
the draining, keep the jug in
position until the operation
is completed. The average
duration for full load drainage
is about three minutes.
If needed, it is possible to
pause the draining process by
tapping PAUSE on the display
(for example in case the jug
would be already full of water in the middle of the
draining process).
The jug must be at least 2 liters large.
Please note: to ensure that the water is cold, it is not possible
to perform this activity before 4 hours have elapsed from the
last cycle (or the last time the product was powered). During
this waiting time, the display will show the following feedback
“WATER IS TOO HOT: WAIT UNTIL THE TEMPERATURE
DECREASES”.
DESCALE
This special function, activated at regular intervals,
allows you to keep the tank and the steam circuit in
the best condition.
The message <DESCALE CYCLE NEEDED> will be
shown on display, to remind you to execute this
operation regularly.
Descale requirement is triggered by the number of
steam cooking cycles performed or steam boiler
working hours since the last descale cycle (see the
table below).
“DESCALE” MESSAGE appears after WHAT TO DO
15 cycles of steam cooking Descale is recommended
22 hours of steam cooking duration
20 cycles of steam cooking It is not possible to run a
Steam cycle until a Descale
cycle will be carried out
30 hours of steam cooking duration
The descaling procedure can also be performed whenever
the user desires a deeper cleaning of the tank and the internal
steam circuit.
The average duration of the full function is around
185 minutes. Once the function is started, follow all
the steps indicated on the display.
Please note: The function can be paused but, if it is canceled at any
time, the entire descaling cycle must be repeated from the
beginning.
»PHASE 1.1: DRAINING (up to 3 min.)
If the reservoir is not empty, the draining phase has
to be performed before starting the proper descaling
process. In this case, please proceed with the draining
task as described in the dedicated Drain paragraph.
Instead, if the reservoir does not contain water, the
appliance will skip automatically to PHASE 1.2.
Please note: to ensure that the water is cold, it is not possible
