Hotpoint CT NTC IX2 UK User manual
Indesit Company UK Ltd
Morley Way,
Peterborough PE2 9JB
www.indesitcompany.com EN Operating Instructions
5
4
3
2
1
7
6
CT NTC IW0 UK
CT NTC IW1 UK
CT NTC IW2 UK
CT NTC IX2 UK
CT NTC UK
02/2013 - ver.1.1
Indesit Company UK Ltd
Morley Way,
Peterborough PE2 9JB
www.indesitcompany.com EN Operating Instructions
5
4
3
2
1
7
6
CT NTC IW0 UK
CT NTC IW1 UK
CT NTC IW2 UK
CT NTC IX2 UK
CT NTC UK
02/2013 - ver.1.1
0
sec
A
B
C
A1 A5
C1 C5
C11
B2 B3 B4
B1
A2 A7
C2
C6
C12
C14 C15 C16
A3 A6
C3
C7
C9 C10
A4
C4
C8.1
C13.2
C13.1
C13.3
C8.2 C8.3
Drinking a lot of water puries your organism, helps your well-being and is the basis of a healthy
diet.
The new Hotpoint Water Machine gives you the certainty of always drinking pure water,
as it springs from the source, because it removes the bacteria and impurities which form along
the way to your tap.
The new Hotpoint Water Machine works by a dual system of treatment: a natural lter
of activated carbon and a UV ray light. These technologies are those traditionally used in the
production of many of the mineral waters of the best brands.
The new Hotpoint Water Machine is very careful with consumption: after a minute of not
being used, it goes on standby and the UV light is turned off. The next time the button is pressed,
the UV light is reactivated to purify the water already present in the device, and this causes
a slight delay in the water coming out.
Finally, the new Hotpoint Water Machine is designed to simplify your life. In fact, it automatically
warns you when it is almost time to change the lter and UV bulb (on average after
a year of use). Without the correct functioning of the lter and the UV light, the Water Machine
does not allow water to come out. In this way, you can be sure that every glass of water that you
drink from the Water Machine will be 99.9999% pure.
The Hotpoint team
Welcome to pure water world,
with a new Hotpoint
WATER MACHINE!
0
sec
A
B
C
A1 A5
C1 C5
C11
B2 B3 B4
B1
A2 A7
C2
C6
C12
C14 C15 C16
A3 A6
C3
C7
C9 C10
A4
C4
C8.1
C13.2
C13.1
C13.3
C8.2 C8.3
Drinking a lot of water puries your organism, helps your well-being and is the basis of a healthy
diet.
The new Hotpoint Water Machine gives you the certainty of always drinking pure water,
as it springs from the source, because it removes the bacteria and impurities which form along
the way to your tap.
The new Hotpoint Water Machine works by a dual system of treatment: a natural lter
of activated carbon and a UV ray light. These technologies are those traditionally used in the
production of many of the mineral waters of the best brands.
The new Hotpoint Water Machine is very careful with consumption: after a minute of not
being used, it goes on standby and the UV light is turned off. The next time the button is pressed,
the UV light is reactivated to purify the water already present in the device, and this causes
a slight delay in the water coming out.
Finally, the new Hotpoint Water Machine is designed to simplify your life. In fact, it automatically
warns you when it is almost time to change the lter and UV bulb (on average after
a year of use). Without the correct functioning of the lter and the UV light, the Water Machine
does not allow water to come out. In this way, you can be sure that every glass of water that you
drink from the Water Machine will be 99.9999% pure.
The Hotpoint team
Welcome to pure water world,
with a new Hotpoint
WATER MACHINE!
55
en
hotpoint.co.uk
PARTS AND FEATURES
1. Water Machine Unit
2. Reservoir Lid
3. Reservoir
4. Dispensing Button and Self Monitoring Sy-
stem Warning
5. Faucet
6. Drip tray
7. Screwdriver
IMPORTANT
• This appliance is for use with potable drin-
king water only. Never use this appliance
with unknown or unsafe sources.
• This appliance needs a regular periodic
maintenance to assure the drinkability requi-
rements of treated water and improvements
preservation as declared by the Manufactu-
rer.
• Check if the voltage indicated on the ap-
pliance corresponds to the local mains volta-
ge before you connect the appliance.
• Do not use this appliance if the mains cord,
plug or other parts are damaged.
• Do not allow children to use the appliance
without supervision.
• Never leave the appliance unattended when
water is being dispensed.
• For a cold refreshing drink the reservoir may
be stored full of water in the fridge.
• Donotoverllthereservoiranddonotleave
the water goes below the min level marked
on the reservoir: running the with a lower le-
vel of water will cause bubbling noises as the
pump will then suck in air.
• Only use original parts from the manufactu-
rer to repair and service the unit.
• Only use Hotpoint [Hotpoint] UV lamps and
lterswiththeappliance,failuretodosowill
void the warranty.
• The UV lamp will turn on for 60 seconds
should the appliance not be used for 3 hours
• Makesuretheapplianceisplacedonaat,
level, dry and secure surface.
• Read all instructions contained in this user
manual prior to using this appliance.
• This Class A system conforms to NSF Stan-
dard 55 and P231 for the disinfection of
micro biologically contaminated water that
meets all other public health standards. The
system is not intended to convert wastewa-
ter or raw sewage into drinking water. The
system is intended to be installed on visually
clear drinkable water.
SET-UP
Check the unit for any damage, if the appliance is
damaged then please return to the place of pur-
chase.
A1 Insert the plug into the mains socket. When
the mains power is switched on the appliance will
automatically go through a self check/test and
once this is complete the button will turn blue.
A2 Remove the water reservoir from the main
body of the appliance .
A3 Remove the lid from the reservoir.
A4 Rinsethereservoirverywellandthenllthe
reservoir from a potable water source. Do not
overllthereservoir.
A5 Wash the lid thoroughly (for cleaning proce-
duresreadpoint3.1)andre-tittothereservoir.
A6 Re-tthereservoirtotheappliancemaking
sureitisrmlytted.
The steps A1-A6 can also be done wi-
thout removing the reservoir from the
66
en
hotpoint.co.uk
body and directly lling it with water, using a
common bottle or jug.
A7 Place a glass or large container under the
dispense area and touch the dispense button to
operate the unit, and touch again to stop the ap-
pliance. Allow water to run through the unit until
the reservoir has been emptied.
Do not consume the water until step A8
has been completed.
The rst 3-5 litres of water dispensed may
contain some ne, black carbon particles. car-
bon is a natural, organic material made from
coconut shell so don’t worry for your safety.
Clear water should be noticed after ushing
through 3 to 5 litres of water (2 to 3 full re-
servoirs).
A8 Repeatstepsa2-a7vetimes(5x):thiswill
completelyushthecarbonfromthenewlter.
PRODUCT USAGE
B1 When the appliance is in standby mode the
button will be blue but when it is touched it will turn
green and water will be dispensed.
If the button is not touched within 2 mi-
nutes of being activated then it will au-
tomatically stop the ow of water and turn the
pump off.
B2 Touch to STOP dispensing water. When you
touch the button to stop water being dispensed
the button will change colour from green to blue.
After one minute the product is in a
stand-by mode, it goes in an energy sa-
ving mode as the UV lamp is off; when the pro-
duct is in this condition, there will be a 2 se-
cond delay before the water is dispensed after
the dispense button is touched so to activate
the UV lamp and purify the water.
Your product has been designed and in-
ternationally certied to the highest
standards of water purication, and guarante-
es at all times, to dispense the best water qua-
lity. The self monitoring system will warn you
of any potential risks, by way of 3 possible
alarms.
B3 Once the Filter has is at 11 months after its
rstusage,theFiltericonwillashasareminder,
andcontinuetoashuntilthelterhasbeenre-
placed as per B4 below. During this time, your
machine will continue to dispense water, until B4
below has been reached.
B4 After a 12 month period, both the UV Bulb
and Filter must be replaced to ensure optimal wa-
terpurication.BoththeUVIconandFilter Icon
will alarm 20 times and ash alternately. When
this occurs, no water will be dispensed, until the
Filter and UV Bulb have both been replaced and
the machine reset (to do this you will need to fol-
low steps C1 to C17).
MAINTENANCE
This product is a high performance water machi-
ne, keeping it in good working order will provide
the reassurance of truly great drinking water.
The uv bulb and lter must be replaced
every 12 months to ensure that your ap-
pliance is dispensing the highest quality drin-
king water.
For the correct and effective appliance
working, use only Hotpoint
[hotpoint] replacement kit (read service sec-
tion)
Unplug the Appliance from the mains
before replacing the UV lamp or lter.
It’s recommended to do next steps on a wa-
shable surface. After this procedure it’s re-
commended that you clean the surface with a
home-use disinfecting product.
C1 Remove the water reservoir from the main
body of the appliance.
C2 Remove the two screws that hold the lid in
place using the screwdriver you can nd in the
box.
C3 Remove the lid from the unit by slightly
pushing it back and then lifting it up.
C4 Disconnect the UV lamp connector by hol-
ding it and pressing in the clip on the connector
77
en
hotpoint.co.uk
C10 Removetheltercartridgefromtheheadby
pulling it out as per illustration.
The lter cartridge can be disposed of
with normal household waste.
Before installing the new ltering car-
tridge, wash the plastic lter body with a
washing up liquid and rinse thoroughly.
C11 Remove the new lter cartridge from the
packagingandtitbyrmlypushingitintothel-
terhead,makingsureitisrmlyandsecurelyt-
ted.Makesurethenewlteryouarettingcomes
in a sealed bag for hygienic purposes.
C12 Screwthelterheadandthelterbodyto-
gether,makingsureitisrmlytightened.
C13 Fitthelterassemblywiththebackintothe
appliance as follows:
1. Insertthelterassemblybackintoitscradle,
aligning the two male spigots with the female
holesinthecradle.Pushrmlyuntilthelter
sitssnuglyandisushinsidethecradleand
with the cradle top surface.
2. Lockthelterbyclosingthelockingleverun-
til it ‘clicks’ into place
3. Rotate the red rotating lever back into the
LOCK position.
C14 Re-tthelid,makingsurethefrontisatta-
chedrst.Ifthelidisnotttedcorrectlytheunit
will not switch on.
Fit the lid making sure the front is
pushed in place rst and then push the
back end with the screws down to give a snug
t.
C15 Re-tthetwoscrewsthatholdtheliddown
using the screwdriver.
The screws should be hand tightened,
do not over tighten.
C16 Insert the plug into the mains socket and
press and hold the dispense button for 10 secon-
dsuntilyouhearabeepasthiswillresetthelter
timer.
and pulling it up.
C5 ToremovetheUVlamprmlypullitupand
out. Do not pull the lamp out at an angle as it may
break or damage the internal parts of the applian-
ce.
The UV lamp must be disposed of cor-
rectly and must not be disposed of with
normal household waste.
C6 Insert the new UV lamp while holding the
white end caps only. Insert the UV lamp as shown
in the illustration and push it all the way down until
it cannot go any further.
Do not use force when removing and in-
serting the UV lamp as you may damage
internal parts. Do not touch the UV lamp glass
surface with your ngers as this will affect the
performance of the UV lamp.
C7 Re-connect the UV lamp connector making
sure the connectors are lined up correctly as they
willonlyttogetherwhencorrectlyaligned.
Pay attention not to wet the UV lamp
connector; in case of water drops on UV
lamp connectors, do not reconnect to power
mains before drying completely.
Wear disposable gloves during the ope-
rations of lter removal hereafter descri-
bed to avoid the direct contact with wet parts.
C8 To remove the Filter, do the following:
1. Rotate the red rotating lever so that it is pa-
rallel with the side panel.
2. Insertyourngerintotheroundholeofthe
lever, and pull the lever up to the vertical
position.
3. Pull the lever straight up to remove the Filter
assembly (some slight force may be requi-
red).
C9 Unscrewthelterbodyfromthelterhead
by turning the base in a anti clockwise direction as
per the illustration.
Be careful as the lter body will contain
water.
88
en
hotpoint.co.uk
If the reservoir contains water, place a
cup or container under the dispense
area before carrying out step C16.
C17 The lter now needs to be ushed, follow
step A2 through to A8.
CLEANING
It is recommended that you maintain your applian-
ce by cleaning it on a regular basis. The appliance
can be cleaned using a damp lint free cloth. Ne-
ver use any alcohol or alcohol based chemicals
or abrasive materials on any part of the product
It is recommended you clean the reservoir unit
and lid with a light solution of dishwashing liquid
with water not warmer than 50°. Never use abra-
sive chemicals or materials as this could scratch
and deface the product.
STORAGE
Never store the appliance with water in the reser-
voir and always store it the correct way up in a
dry environment. If the unit has not been used for
more than 3 months it is recommended that the
lterbereplacedbeforetheapplianceisused.
SAFETY
• Only trained competent technicians should
carry out repairs on the appliance.
• Packing materials could present a trip ha-
zard. Keep them off the oor and out of
reach of infants and small children.
• Avoid the power plug and cord contacting
water or moisture. Should this happen,
unplug the lead from the power source and
discontinue using the appliance until dee-
med safe to do so.
• GROUNDING INSTRUCTIONS – This ap-
pliance must be grounded. In the event of
a malfunction or breakdown, grounding will
reduce the risk of electric shock by providing
a path of least resistance for electric current.
This appliance is equipped with a cord ha-
ving an appliance-grounding conductor and
a grounding plug. The plug must be plugged
into an appropriate outlet that is installed and
grounded in accordance with all local codes
and ordinances
Improper connection of the appliance-
grounding conductor can result in a risk
of electric shock. Check with a qualied elec-
trician or service representative if you are in
doubt whether the appliance is properly
grounded. Do not modify the plug provided
with the appliance; if it will not t the outlet,
have a proper outlet installed by a qualied
technician.
Isolate power supply before removing
cover.
• Should a fault occur on the appliance always
unplug it from the mains power supply.
• If the power lead is damaged in any way it
must be replaced by an authorized dealer or
qualiedperson.
• Unplug the appliance before removing any
part of the appliance for servicing.
• Do not touch or look directly into the faucet.
• We recommend that the appliance should
not be handled or lifted by holding the reser-
voir, especially when the reservoir is full of
water.
• The lter and UV lamp must be replaced
every 12 months.
• Never use any chemicals or abrasive mate-
rials on any part of the product.
• This appliance is not intended for use by per-
sons (including children) with reduced physi-
cal, sensory or mental capabilities, or lack
ofexperienceandknowledge, unlessthey
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• Never immerse the appliance in water or
spray any liquid onto the outside of the ap-
pliance.
TROUBLESHOOTING
If there is no water being dispensed:
• Check that the unit is plugged in and
switched on at the mains wall socket.
• Checkthatthereservoiristtedcorrectly.
• Check that there is water in the reservoir.
99
en
hotpoint.co.uk
• Make sure that the top cover is tted cor-
rectly.
• Make sure the button is blue.
Should there be no response from the button re-
move the power cord and wait 10 seconds before
plugging it back in. This will reset the appliance.
Should the appliance be faulty please either re-
turn the product in its original packaging with
proof of purchase or contact the local Hotpoint
[Hotpoint] customer service centre.
In the unlikely event that the UV bulb should fail
the UV icon will ash and alarm 20 times. No
water will be dispensed until steps C1 to C7 and
steps C14 to C15 are completed.
CERTIFICATION
The appliance has attained and complies with the
followingcerticationsanddirectives:
CE, NSF 42 & 53, NSF 55a, NSF P231,
RohS, REACh.
GUARANTEE
12 months Parts and Labour Guarantee
Thiscerticateofguaranteerepresentsthegua-
rantee (“Guarantee” hereinafter) offered by In-
desitCompanyUKLimitedwithregisteredofce
at Peterborough PE2 9JB in relation to products
purchased in the United Kingdom and Indesit
IrelandLimitedwithregisteredofceinDublin9,
Ireland for products purchased in the Republic of
Ireland. This Guarantee does not affect your sta-
tutory rights.
Your product has the benet of our manufactu-
rer’s Guarantee, which covers the product for
twelve months from the date of purchase.
This gives you the reassurance that if, within that
time, your product is proven to be defective be-
cause of either workmanship or materials, we will,
at our discretion, either repair or replace the pro-
duct at no cost to you.
This Guarantee is subject to the following condi-
tions:
• Documentary proof of original purchase date
is provided.
• Cosmetic damage must be reported within
14 days from the date of purchase.
• The product has been installed and operated
correctly and in accordance with our opera-
ting and maintenance instructions.
• The product is used only on the electricity
supply printed on the rating plate.
• The product has been used for normal do-
mestic purposes only.
• The product has not been altered, serviced,
maintained, dismantled, or otherwise interfe-
red with by any person not authorised by us.
• Any repair work must be undertaken by us or
our appointed agent.
• Any parts removed during repair work or any
product that is replaced become our proper-
ty.
• The product is used in the United Kingdom
or Republic of Ireland.
The Guarantee does not cover:
• Damage resulting from transportation, im-
proper use, neglect or interference or as a
result of improper installation.
1010
en
hotpoint.co.uk
• Accidental damage, this includes but is not
limited to, damage which occurs as a result
ofanexternalaction.
• Replacement of any consumable item or ac-
cessory. These include but are not limited to:
• plugs, cables, light bulbs, hoses, brushes,
coversandlters.
• Replacement of any removable parts made
of glass or plastic.
After Sales Service
No one is better placed to care for your Hotpoint
product during the course of its working life than
us – the manufacturer.
Essential Contact Information
Advice Line
We have a dedicated team who can provide free
advice and assistance with your product if you
experience any technical difculties. Simply call
our Hotpoint Service Hotline on 08448 240 055
(Republic of Ireland 0818 904 041) for telephone
assistance.
Please note:
Our advisors will require the following infor-
mation:
Model number:
Serial number:
Consumables and Accessories
We supply a full range of consumables and ac-
cessories to keep your product functioning ef-
ciently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
www.hotpoint.co.uk
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to
helping the environment, Hotpoint reserves the
right to use quality, recycled components to keep
down customer costs and minimise material wa-
stage.
Please dispose of packaging and old products
carefully.
Register your new product and get a second
year FREE!
Wewanttogiveyouadditionalbenetsofowner-
ship of your product and offer you an additional
free 1 year guarantee when you register your
product with Hotpoint within 28 days of purchase.
If you do not register your product with Hotpoint
within 28 days, your product is guaranteed for 1
year only.
To activate your 2 year guarantee register with
us online at www.hotpoint.co.uk. Please note that
the 2 year guarantee is only available in UK and
Ireland and is subject to the same conditions as
the1yearGuarantee.Pleaserefertothecertica-
te of guarantee for more information.
DISPOSAL OF OLD
ELECTRICAL APPLIANCES
The European Directive 2002/96/
EC on Waste Electrical and Electro-
nic Equipment (WEEE), requires
that old household electrical ap-
pliances must not be disposed of in
the normal unsorted municipal wa-
ste stream.
Old appliances must be collected separately in or-
der to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected. Consumers should contact their local
authority or retailer for information concerning the
correct disposal of their old appliance.
1111
en
hotpoint.co.uk
Unit of
measure-
ment
Limit value
Italian Legis-
lative Decree
31/01 and
following
amendments.
Pre-
ltration
water 1 l
Post-
ltration
water 1 l
Δ 1l
Pre-
ltration
water
1501 l
Post-
ltration
water
1501 l
Δ 1550 l
Trichloromethane µg/l * 22 <0.5 -100% 24 6.4 -73%
Bromodichloromethane µg/l * 8.6 <0.5 -100% 9.5 0.5 -95%
Dibromochloromethane µg/l * 7.9 <0.5 -100% 6.4 <0.5 -100%
Tribromomethane µg/l * 4.7 <0.5 -100% 1.5 <0.5 -100%
Sum of trihalomethanes µg/l 30 43.2 -/- -100% 41.4 6.9 -83%
Chlorite µg/l 700 4000 <90 -100% 370 <90 -100%
-/- = below detectability limit
*=Parameterswhosemaximumlimitisexpressedassumoftrihalomethanes
A reduction performance of 100% was considered for parameters below the detectability limit after
ltration
PARAMETERS AND PERFORMANCE VALUES
Indesit Company UK Ltd
Morley Way,
Peterborough PE2 9JB
www.indesitcompany.com EN Operating Instructions
5
4
3
2
1
7
6
CT NTC IW0 UK
CT NTC IW1 UK
CT NTC IW2 UK
CT NTC IX2 UK
CT NTC UK
02/2013 - ver.1.1
This manual suits for next models
3
Table of contents
Popular Water Filtration System manuals by other brands
Dreamer
Dreamer DHA-WPA160W user manual
PREMIER TECH
PREMIER TECH Ecoflo STB-650B owner's manual
Crystal Quest
Crystal Quest Whole House Installation and operation guide
ClearPlus
ClearPlus WH2-HF manual
Sterilight
Sterilight Ozone S2ROZAP Installation instructions and owner's manual
EHEIM
EHEIM 2006 instructions
Chungho
Chungho Premium Plus user manual
Blueair
Blueair DustMagnet 5210i user manual
Axeon
Axeon Hydrogen user manual
Fiap
Fiap TrommelSieve Active Series operating instructions
Netafim
Netafim Arkal 2" Spin-Klin Compact Stand Alone... Installation and operation instructions
Weller
Weller WFE 20D operating instructions
