26
Dublin
Street,
Carlow
,
Ireland.
Te l : +353 (0)59 914 0345 Fax: +353 (0)59 914 0543 Email: [email protected] Web: www.hotron.comHotron Ltd.
Touch the middle of the key pad. Key in the following digits 1,2,3,4
1,2,3,4 #1#
Access Card (Serial registration is possible)
OR
Card address(0001~1000) →Access Card
* (End)
1. Function (0) Digital Push Pad Deactivation
Function (1) Digital Push Pad Activation
2. Digital Push Pad Setting 3. Digital Push Pad Deleting
7. Deleting a Card / Password
9. Clear All Cards / Passwords
STEP 1
Card registration (Card type : ISO 14443)
Card : Key in 4 digit Master Code twice #8#Access Card(Serial possible) # *
Password : Key in 4 digit Master Code twice #8#(then 4 digit keycode you
want to delete) # *
6. Deleting a Card Address
Key in 4 digit Master Code twice #3# Card address(4digit or serial delete) # *
4. Adjusting Back Light (up to 9)
Key in 4 digit Master Code twice #12# 0~9 # *(0: off 9: Brightest / Default : 2)
5. Contact Time
Key in 4 digit Master Code twice #5# 01~60(1Sec.~60Sec.) # *
(Default : 2Sec.)
8. Contact Change (NO or NC)
Key in 4 digit Master Code twice #9# 0/1 # (0: NO, 1: NC / Default : NO)
Cards : Key in 4 digit Master Code twice #6#
Passwords : Key in 4 digit Master Code twice #7#
10. Restore factory settings
Key in your 4 digit Master Code twice *#.
Once completed, your 4 digit Master Code is deleted.
To set a new Master Code, repeat step 2 above.
STEP 2
Set a new 4 digit Master Code
for main menu access
Touch the middle of the
key pad.
STEP 4
Select your required function,
function (0) Card, Digital Key Pad or
function (1) Digital Key Pad only or
function (2) Card only
Touch the middle of the
key pad.
Key in your 4 digital
Master Code twice, then
press #10#
(insert 0 or 1 or 2) # *
Default function (0)
Card, Digital Keypad mode.
Default function (1) Digital Push Pad Activation Every time you change, it will change set on and off
[Caution!] You must activate additional function before you
set digital push pad function
Every time you change, it will change set on and off
[Caution!] You must activate additional function before you
set digital push pad function
STEP 3
Set a Keycode Password
Key in your 4 digital
Master Code twice,
then press #2# (insert 4 digit
keycode password) # *
Touch the middle of the
key pad.
Key in the following digits if
setting a master code for the
first time. 1,2,3,4 1,2,3,4
#*## 1,2,3,4# (insert new
master code) #
If changing a previous installed
master code, perform the
sequence above and replace
the default digits 1,2,3,4 with
the current master code.
Note : Serial registration (If the first address is [0100], next address is [0101] automatically increase.)
Register by ISO 14443 (13.56MHz) Card only
: Error : Power : Action / Set
Power (DC 12~30V, AC 12~24V)
Brown
Orange
Yellow
Yellow
White
White
Gray
Gray
External Input
Output Contact
+12V Output(Lock Power)
GND Output (Lock Power)
Wiring
Key in the following digits
(Enter your saved 4 digit
keycode)
followed by the keys 9 *,
Digital Touch Pad will
be activated.
Tap HR80-HW several
times then the number
will show up.
(Enter your saved 4
digit keycode)
followed by the
keys 9 *
Key in your 4 digital Master
Code twice, then press
#11# (insert 0 or 1) # *
11. Sensor Lock function
Lock function on : Password + *
Lock function off : Password + #
Sensor output contact
Card reader output contact
Automatic door controller
Contact Output : NC
Note : Once the keycode password is saved, test by
entering the saved keycode and then press the # key.
The red icon on the HR80-HW should
be displayed showing it is operating correctly.
Note : When you set the card function only, the keycode
doesn’t work. But if you want to change the function,
Tap HR80-HW several times then the number
will show up.
ADDITIONAL INSTRUCTIONS
(white) (yellow)
