Household Essentials 18400-1 User manual

18400-1 Instruction Manual
Tilt-out Laundry Sorter Cabinet

A - 1pc
Cabinet Top Panel
D - 2pcs
Front Bin Panels
F - 2pcs
Cross Brace
E - 2pcs
Back Panel
G - 2pcs
Bag
C - 2pc
Cabinet Side Panel
B - 1pc
Cabinet Base Panel
Please read the entire instruction booklet prior to assembling your
Tilt-out Laundry Sorter Cabinet. Check the parts and tools list below to ensure
you have everything to properly install your ironing board. If you are missing
parts please do not return to place of purchase, call Household Essentials® at
800.922.5524/314.428.5657 and we will expedite replacement parts.
NOTE:
In order to prevent damage during assembly, it is recommended to assemble with at
least 2 people.
For more information on the Tilt-out Laundry Sorter Cabinet
and its accessories, visit our website www.householdessential.com.

H - 2pcs
Handle Set
I - 62pcs
Self Tapping
Screws
L - 16pcs
Cam Lock
M - 4pcs
Bag Handles
O - 4pcs
Hinge
P - 2pcs
Magnet Lock
(Magnet and
Magnet Bar) Q - 4pcs
Side Bin Frame
N - 4pcs
Bin Frames
J - 6pcs
Adjustable Feet
K - 16pcs
Cam Bolt

Preparing and Assembling Cabinet
(Do Not Use Power Tool When Securing Cam Locks):
1. Screw in 6 Adjustable Feet (J) into base panel (B).
NOTE: Feet are adjustable to accommodate different floors. Shown in Diagram 1.
2. Insert 6 cam bolts (K) into the top (A) as shown on diagram 2.
3. Insert 6 cam bolts (K) into the top (B) as shown on diagram 2.
4. Insert 2 cam bolts (K) into each side panel (C) as shown on diagram 3.
Diagram 1
Diagram 2
Diagram 3
NOTE: Turn the cam
bolt screws until they
are tight, the shoulder
should be against the
surface of the part.
B
B
J
J
J
J
JJ
A
K
KK
KK
K
K K K
K
KK
K
K K
K
C
C
L
K

C
F
F
C
Diagram 4
Diagram 5
B
C
L
L
L
L
Diagram 6
5. Install 1 cross brace panel (F) into the bottom cam bolt of both side panels (C).
Make sure the 2 holes on side of brace are facing down. Diagram 4.
6. Install the other cross brace panel (F) into the top cam bolts of side panels (C).
Make sure the 2 holes on side of brace are facing up. Diagram 4.
7. Insert cam lock (L) into side panels (C) and secure by locking the cam bolts and locks.
8. Place base panel (B) onto side panels by inserting cam bolts into holes.
Insert cam lock (L) and secure by locking the cam bolts and locks. Shown in Diagram 5.
9. Turn cabinet right side up and sit on feet. Place top panel (A) onto cabinet by inserting
cam bolts into holes. Insert cam locks (L) and secure by locking the cam bolts
and locks. Shown in Diagram 6.
10. Take 2 back panels (E) and attach to top and bottom back of cabinet by using
18 screws (I). Shown in Diagram 7. White side facing the inside. This should result in
approximately a 3 inch gap at the center of the unit.
L
L
L
L
C
A
E - white side
3” gap
E - white side
Diagram 7
E
I
I
I
E

11. Using predrilled holes, attach 2 hinges (O) to base of door (D) by using 6 screws (i).
Shown in Diagram 8. Repeat with other door. Set doors aside.
12. Install both magnet (P) to underneath of top by lining up predrilled holes and
using 2 screw (I). Attach magnet bar to inside of door with two screw s (I) by lining
up with predrilled holes. Repeat to other door with other magnet bar.
Shown in Diagram 9.
13. Install 1 handle set (H) to cabinet door (D) by using predrilled holes.
Repeat with other door. Shown in Diagram 10.
14. Install doors to Cabinet Base (B) by aligning the hinges with predrilled holes and
using 6 screws (I).
NOTE: Align and secure the center hole on both hinges. Then secure the hinges with the
remaining other two screws.
Diagram 8
Diagram 10
Diagram 11
Diagram 9
O
D
D
D
HH
D
O
O
O
IIII
I
II
PP
II
P
P
I
I
I
I
I

Diagram 14
Diagram 15
I
I
Q
15. Insert 1 bin frame (N) into side bin supports (Q) Diagram 12.
Screw into door by lining up predrilled holes and using 3 screws (I).
Shown in Diagram 13. Place second bin frame at the back of bin support.
NOTE: Bent end of side support (Q) is behind the lip of top A.
16. Repeat step 15 on other door.
17. Take bag handles (M) and insert into bags Shown in Diagram 14.
Place bags in cabinet. Be sure to put handles between ball and outside frame to
keep bags from sliding. Shown in Diagram 15.
NOTE: After completion of assembly you may need to make adjustments to the leveling
feet to either make the cabinet level or to help align the doors. If your cabinet is not level,
the doors will not align properly.
Diagram 13
N
M
M
N
Diagram 12
QQ
N

© 2015 Household Essentials LLC, All Rights Reserved
5895 North Lindbergh Blvd. • Hazelwood, MO 63042 • 1-800-922-5524
1-314-428-5657 • FAX [phone] • www.householdessential.com
3/25/15