Gotrax EDGE User manual

EDGE
USER MANUAL
A S M A R T E R H O V E R B O A R D

This user manual will help you operate your new hoverboard. Be sure
to read ALL OF THE INFORMATION in this manual be ore riding.
NOTE TO ALL RIDERS UNDER 18 YEARS OF AGE:
It’s very
important that you get parental permission be ore riding your
hoverboard.
Congratulations
on our purchase!

ALWAYS wear a helmet when riding your hoverboard.
Make sure your hoverboard has a full batter be ore taking it out
to ride.
Alwa s be aware o local road laws, and ollow them.
Do not ride the hoverboard under the influence of drugs or alcohol.
Alwa s respect pedestrians.
Do not ride under wet conditions. The hoverboard may slide rom
under your eet causing injury. Wet conditions may damage the
electronics and void the warranty.
Maximum Speed: Your hoverboard goes a maximum speed o 6.2
mph.
Don’t ride until ou read this

1. Avoid water - The hoverboard is not waterproo . The electronics may
be damaged due to water and water damage is not covered by our
warranty. Riding in wet conditions is also very dangerous and may result
in injury.
2. Abuse - We do not cover physical damage due to negligent care and
extreme riding.
3. Whenever ou ride the GOTRAX Hoverboard, you risk severe
injury or even death rom loss o control, collisions, and alls. Use
caution and ride at your own risk.
4. Do not modify the product from the manufacturer’s original design.
5. Keep hands and all body parts away rom moving parts while
operating the hoverboard.
6. Before riding - be sure to check the hoverboard over and make sure
the hoverboard is operating correctly be ore each use.
7. The hoverboard should never be used by children under the age o 8.
8. Never exceed the 176 lb maximum load rating.
Warning Message

You should find each of these items in your box:
1. Electric Hoverboard
2. Approved Power Adapter / Charging Unit
Remove all packaging material, then inspect each item or any accidental
damage that may have occurred during shipping.
1. SRX PRO Hoverboard
2. SRX PRO Approved Power Adapter / Charging Unit
Remove all packing material, then inspect each item or any
accidental damage that may have occurred during shipping.
Unpack

The hoverboard comes ully assembled.
Get to know our hoverboard
Specifications
Top Speed:
Distance per Charge:
attery Type:
6.2 mph
3.1 Miles
25.2V 2.6AH
attery Charger:
Charge Time:
Motor Power:
DC29.4V 0.6A
5 Hours
200W

Be ore using the hoverboard, you must ully charge the battery.
1. Insert the charging plug into the port.
2. The charger box will have a green light when ully charged and a red
light when charging.
3. Charging Time: 5 hours.
1. Insert the charging plug into the port.
2. The charger box will have a green light when ully
charged and a red light when charging.
Charge our hoverboard

To power the hoverboard on, press and hold the silver button on the back o your
hoverboard or 1 second.
To power the hoverboard off, press and hold the silver button on the back o
your hoverboard or 1 second.
Mode Switch:
1. Double-click the switch button within 1.5 seconds in the shutdown state to switch
between sel -balancing and non-balancing modes.
2. In the sel -balancing mode, the hoverboard can not be turned o; by pressing
the switch button in the riding state, and can be turned on and o; normally in the
standby state.
3. In the non-sel -balancing mode (karting mode), the hoverboard can be switched on
and o; normally in the riding state and the standby state.
Forward Acceleration: Gently push down with your toes. Be prepared to lean
orward slightly as the board accelerates.
Backward Acceleration: Gently li t your toes. Be prepared to lean backward as
the board accelerates.
Hoverboard Functions

To Turn Right: Push gently down with your le t toes. Be prepared to shi t your weight
to the right.
To Turn Left: Push gently down with your right toes. Be prepared to shi t your weight
to the le t.
Slow to Stop: Return to an upright position with your weight evenly balanced.
Low Batter : When the hoverboard is low on battery and about to die, the
hoverboard will beep and flash red on the LED lights. Once it starts beeping and you
see the red LED light, get off of the hoverboard and charge.
Overheat Alarm: The motor will overheat a ter a long time o high speed
running. When the motor temperature is high, it will keep beeping, and the
hoverboard will move very slowly. Meanwhile, the red light will be flashing
all the time. I it continues to run, the control system will cut o; the power to
protect the motor rom damage.
Warning: To prevent overheating, when the motor temperature is too high
and the alarm is beeping, please stop riding the hoverboard, and wait or
the motor cool down be ore riding.

1. You will want to start riding your hoverboard by mounting the board
from the rear. The rear of the board can be identified by the power
button and the charging port.
2. Place your hoverboard on the ground directly in ront o your eet. Step
with one oot onto the plat orm, and then quickl step up onto the
hoverboard with your second oot.
3. Always dismount rom the back o the hoverboard.
4. The hoverboard per orms best when on a smooth sur ace e.g. carparks,
smooth roads, ootpaths.
5. Always clean your hoverboard (wheels, platform, etc.), it’s a machine
and it needs to be maintained.
6. Be aware o the terrain you are riding on, watch out or curbs and
obstacles!
Riding Tips

If ou regularl clean and maintain our electric hoverboard, it
will extend its life.
Cleaning and storage: I the hoverboard is dirty, wipe it clean with a
so t damp cloth.
DO NOT use alcohol, gasoline, kerosene, or other corrosive chemical
solvents to clean the hoverboard. It can severely damage the appearance
and structure o the hoverboard. Please do not use a pressure washer as it
may also cause damage to the electronics.
Storage: When you’re not using your hoverboard store in a dry and cool
location. Avoid storing your hoverboard outdoors because sun exposure
can damage its appearance and may cause wear on the li e o the battery
and tires.
Maintenance & Repair

Troubleshooting: One o the most common solutions or hoverboard
issues is calibrating your board. Here are the steps involved in
hoverboard calibration:
1. Start with the hoverboard powered o;.
2. Adjust the oot pedals until they are level with each other and the
ground.
3. Press and hold the power button for 10 seconds. The LED lights will
flash.
4. Press the power button to turn o;.
5. Press the power button to turn on. The hoverboard will be calibrated
and ready or galactic adventures.
NOTE: You may have to repeat the above process multiple times in order
to ully reset and calibrate your hoverboard. For example, you may have
to go through the process 3 times in a row be ore the calibration ully
takes e;ect.

Only use the approved GOTRAX power adapter to charge your
hoverboard, others may cause risk of fire & equipment may be damaged.
Improper disposal o used batteries may seriously pollute the environment.
Please comply with local disposal regulations.
Make sure to store your hoverboard and power adapter in conditions that
do not exceed 104 degrees Fahrenheit or below 32 degrees Fahrenheit.
Warning - Risk o Fire - No User Serviceable Parts, The prolonged
exposure to UV Rays, Rain and the Elements may damage the enclosed
materials, store indoors when not in use.
Batter Information

We frequently update our user manuals at GOTRAX.com, and reserve the
rights to update and change manuals online.
Please contact our customer service team if ou are
experiencing problems or need more detailed information.
The can be reached at GOTRAX.com
Warrant
For warranty in ormation, please visit GOTRAX.com.
Troubleshooting

#RideGOTRAX
W W W . G O T R A X . C O M

GOLABS, INC
GOTRAX.com
2201 Luna Rd.
Carrollton, TX 75006