Hoymiles HMT-1800 Series User manual

• Loose the five screws with the screwdriver.
Untighten the nut shown as picture and
remove the extra cable.
• Slightly screw the nut back to the body,
plug in the 3P-AC bus end cap and tighten
the nut.
• Plug the upper cover back to the 3P-AC
bus connector.
2. Installation Steps
1. Accessories
2.1 Pre-installation
All accessories above are not included by the package, will
need to be purchased separately. Please contact our sales
representative for the price (M8 screws will need to be
prepared by installer-self).
Please make sure the microinverter install under the required environment.
(Please refer to product user manual for more details).
A ) Plan the cable length to allow the bus cable align with
each PV module.
B ) Install the AC bus end cap:
• Use the 3P-Bus connector unlock tool to
unlock the connector upper cover;
ITEM DESCRIPTION
A 3P-AC Bus End Cap, IP67
B
3P-AC Bus Connector
C
3P-AC Connector Unlock Tool
D 3P-Bus Connector Unlock Tool
E 3P-AC Sub Cap
F M8*25 screws
G DC Extension Cable,1m
H
B C D E F GH
3P-AC Bus Cable, 12/10 AWG Optional
2.2 Installation Steps
Step 1. Fix Microinverter on the Rail
A ) Mark the approximate center of each panel on the frame.
B ) Fix the screw on the rail.
*Note:
© 2020 Hoymiles Power Electronics Inc. All rights reserved. AP040299 REV1.1
Installing HMT-1800/2250 Three-Phase Microinverter
Quick Installation Guide
A

Step 2. Complete the AC Connection
A ) Attach the 3P-AC Bus Cable with the
mounting rail, and fix the cable by tie wraps.
B ) Take the AC connector from the micro-
inverter and push it into the 3P-AC bus
connector until it clicks.
C ) If any bus port is vacant, please plug the
3P-AC sub cap into the port to protect it
from dust and walter.
Note: Under the circumstance that need to remove the
inverter AC cable from 3P-AC bus connector,
please use the 3P-AC connector unlock tool and
insert the tool into the side of AC port to remove.
Step 3. Install AC End Cable
A ) Prepare the 3P-AC End Cable with the proper
length, insert one side of the cable into the seal
nut. Match the L1, L2, L3, N and Ground line into
the slot accordingly. Tighten the screws, and then
tighten the cap back to the connector. Plug the
upper cover back to the 3P-AC bus connector.
B ) Connect the other side of the AC End Cable to
the distribution box, and wire it to the local grid
network.
Step 5. Connect PV Modules
A ) Mount the PV modules above the micro-
inverter
B ) Connect the PV modules’ DC cables to the
DC input side of the microinverter.
Step 6. Energize the System Step 7. Monitoring System Set Up
A )
B )
Turn on the AC breaker for the branch circuit.
Turn on the main AC breaker for the house. The system
will start to generate power after several minutes.
Refer to the DTU User Manual or DTU Quick Install Guide,
and Quick Installation Guide for HMP Online Registration
to install the DTU and set up monitoring system.
Step 4. Create an Installation Map
A ) Peel the removable serial number label from
each microinverter (shown as picture).
B ) Affix the serial number label to the respec-
tive location on the installation map
C ) Hang the microinverter on the screw (shown as picture ),
and tighten the screw. The silver cover side of the
microinverter should be facing the panel.
Note: Install the microinverter with the silver side up and under the
PV module. Allow a minimum of 2cm around the micro-
inverter enclosure to ensure ventilation and heat dissipation.
Note: Minimize the distance between the microinverter
and the 3P-AC bus connector for slack.
Tosheet ______
Tosheet ______ AP040228 REV1.1
Panel Group:
Azimuth:
Tilt:
Sheet____of____
Customer Information: DTU Serial Number:
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
Tosheet ________
Tosheet ________
© 2020 Hoymiles Power Electronics Inc. All rights reserved. AP040299 REV1.1
Product information is subject to change without notice. (Please download reference manuals at www.hoymiles.com).
N
PE
L3
L2
L1
138264700571
138264700571