Hoymiles HYT-5.0HV-EUG1 User manual

HYT-5.0HV-EUG1/AUG1
HYT-6.0HV-EUG1/AUG1
HYT-8.0HV-EUG1/AUG1
HYT-10.0HV-EUG1/AUG1
HYT-12.0HV-EUG1/AUG1
Open Energy for All
Quick Installation Guide
Hybrid Inverter
hoymiles.comRegion: Global REV1.3

1 General Declaration
01
Hybrid Inverter Quick Installation Guide
2 Packing List
Inverter*1
Bracket*1 Communication Box*1
Double Row Plug*1 Document*1
EPS Connector*1
Grid Connector*1
Generator Connector*1
M6 Expansion Screw*4
Sleeve*4 Ground Terminal*1 M4 Setscrew*1
DTS*1
Accessories packing list
M3 Setscrew*6 Communication
Terminal*12 AC Terminal*15
PV Connector(+)*3
PV Connector(-)*3
Battery Connector(+)*1
Battery Connector(-)*1
Optional (Wi-Fi, Ethernet, 4G)
Smart Meter*1 CT*3
• The information in this quick installation guide is subject to change due to product updates or other reasons.
• This guide cannot replace the product labels or the safety precautions in the user manual unless otherwise
specified. All descriptions here are for guidance only.
• Before installations, read through the quick installation guide and the user manual to learn about the product
and the precautions.
• All installations should be performed by trained and knowledgeable technicians who are familiar with local
standards and safety regulations.
• Check the deliverables for correct model, complete contents, and intact appearance. Contact the manufacturer
if any damage is found or any component is missing.
• Use insulating tools and wear personal protective equipment when operating the equipment to ensure
personal safety. Wear anti-static gloves, clothes, and wrist strip when touching electron devices to protect the
inverter from damage. The manufacturer shall not be liable for any damage caused by static electricity.
• Strictly follow the installation, operation, and configuration instructions in this guide and user manual. The
manufacturer shall not be liable for equipment damage or personal injury if you do not follow the instructions.
• All cables in this article are copper cables.

3 Mounting the Inverter
4 5
© 2022 Hoymiles Power Electronics Inc. All rights reserved. 02
Hybrid Inverter Quick Installation Guide
≥200 mm
≥300 mm
≥200 mm
≥500 mm
≥300 mm
≥15°
© 2023 Hoymiles Power Electronics Inc. All rights reserved. 02
Hybrid Inverter Quick Installation Guide
23
175 mm 75 mm
65 mm

4 Wiring Diagram
Wiring diagram for countries such as Australia, New Zealand, South Africa, etc. Please follow local wiring regulations.
Hybrid Inverter Quick Installation Guide
03
E-BAR
Battery
BMS
Backup
Loads
Smart
Meter
PV
RCD
Grid
Normal Loads
Distribution Box
PE
or
N
L1
L2
L3
N
PE
EPS
GRID
Meter
L1
L2
N
PE
L1
L2
L3
N
PE
L1
L2
L3
N
PE
CT1
CT2
CT3
Utility
Meter
RCD
①
②
③
④
⑤
⑥
⑦
Do not connect this terminal
when the neutral wire and PE
wire are connected together.
N-BAR
E-N
Link
LOAD
GRID
HYT-HV Series
L1
L2
L3
L3

Note: ·
If the battery has integrated a readily accessible internal DC breaker, then no additional ①DC breaker is required.
© 2023 Hoymiles Power Electronics Inc. All rights reserved. 04
Hybrid Inverter Quick Installation Guide
Model
HYT-5.0HV-G1 25 A/600 V
DC Breaker
HYT-6.0HV-G1 HYT-8.0HV-G1
HYT-10.0HV-G1 HYT-12.0HV-G1
25 A/600 V DC Breaker 40 A/600 V DC Breaker 40 A/600 V DC Breaker 40 A/600 V DC Breaker
16 A/400 V AC Breaker 16 A/400 V AC Breaker 20 A/400 V AC Breaker 25 A/400 V AC Breaker 25 A/400 V AC Breaker
Depends on Loads
Main Breaker
30 mA RCD
① ② ④ ⑤ ⑥⑦
20 A/400 V AC Breaker 25 A/400 V AC Breaker 32 A/400 V AC Breaker 32 A/400 V AC Breaker 32 A/400 V AC Breaker
③
·
The use of ⑥⑦ 30 mA RCD is recommended but not mandatory; please comply with local regulations for the system installation.

Wiring diagram for other countries, please follow local wiring regulations.
Hybrid Inverter Quick Installation Guide
05
E-BAR
Smart
RCD
Normal Loads
Distribution Box
PE
or
N
L1
L2
L3
N PE
EPS
GRID
Meter
L1 L2 L3 N PE L1 L2 L3 N PE
L1 L2 L3 N PE
CT1 CT2 CT3
RCD
①
②
③
④
⑤
⑥
⑦
LOAD
GRID
Backup
Loads
Grid
Utility
Meter
Meter
PV
Battery
BMS
HYT-HV Series
L1
L2
L3

Note: ·
If the battery has integrated a readily accessible internal DC breaker, then no additional ①DC breaker is required.
·
The use of ⑥⑦ 30 mA RCD is recommended but not mandatory; please comply with local regulations for the system installation.
© 2023 Hoymiles Power Electronics Inc. All rights reserved. 06
Hybrid Inverter Quick Installation Guide
Model
HYT-5.0HV-G1 25 A/600 V
DC Breaker
HYT-6.0HV-G1 HYT-8.0HV-G1
HYT-10.0HV-G1 HYT-12.0HV-G1
25 A/600 V DC Breaker 40 A/600 V DC Breaker 40 A/600 V DC Breaker 40 A/600 V DC Breaker
20 A/400 V AC Breaker 25 A/400 V AC Breaker 32 A/400 V AC Breaker 32 A/400 V AC Breaker 32 A/400 V AC Breaker
Depends on Loads
Main Breaker
30 mA RCD
① ② ④ ⑤ ⑥⑦③
16 A/400 V AC Breaker 16 A/400 V AC Breaker 20 A/400 V AC Breaker 25 A/400 V AC Breaker 25 A/400 V AC Breaker

5 Electrical Connection
Step 1 Grounding Protection Wire
Step 2 Grid (Same wirings for GEN if needed)
Step 3 EPS
Hybrid Inverter Quick Installation Guide
07
23
5
4
4
1
Click
5
2
3
1
13 mm≤≤18 mm S=4 mm²
7-8 mm
20-25 mm
1
2
4
5
1
2
5
2
3
1
4 mm²≤S≤6 mm²
7-8 mm
20-25 mm
13 mm≤≤18 mm
6
1
4
53
2
4M4
1.2 N·m
3
2
4
M4
1.2 N·m
1
5
4
3
1 2
M4
1.2 N·m
L=H+(2-3) mm
S≥4 mm²
S H
L

© 2023 Hoymiles Power Electronics Inc. All rights reserved. 08
Hybrid Inverter Quick Installation Guide
Step 4 PV
1
23
1
BAT+
BAT-
1
2 3
Click
4
PV+
PV-
1
3
321
PV+
PV-
4
2
Φ: 4-5 mm
2.5 mm²≤S≤4 mm²
S
Φ
7-8 mm
Step 5 Battery
321
Click
3 4
BAT+
BAT-
4
2
: 4-6 mm
S=6 mm²
Φ
ΦS
7-8 mm
4

Step 6 Signal Communication (Connection of communication box is mandatory)
Label
Meter (485A, 485B)
BMS (CANH, CANL, 485A, 485B)
DRM (D1/5, D2/6, D3/7, D4/8, REF, COM)
DI (IN-, IN+)
Parallel (DI IN+, DI IN-,CANH, CANL, 485A_1,
485B_1, 485A_2, 485B_2)
120 Ohm (ON, OFF)
DO1 (NO1, COM1)
DO2 (NO2, COM2)
Description
For the Smart Meter.
For Li-ion battery communication via CAN or RS485.
For external Demand Response Enabling Device.
Dry-contact input of external bypass contactor.
For parallel operation.
120 Ohm termination resistor for parallel operation.
Dry-contact output. The DO1 can be set to one of the
functions as follows: Earth Fault Alarm, Load Control
Dry-contact output. The DO2 will control the bypass
contactor under certain logic.
Hybrid Inverter Quick Installation Guide
09
8-485A_2
7-485B_2
2
6-485A_1
5-485B_1
4-CANL
1
3-CANH
2-DI IN-
1-DI IN+
8-NC
8-485B
8-485A_2
7-NC
7-485A
7-485B_2
6-NC
6-NC
6-485A_1
5-485B
5-CANL
5-485B_1
4-485A
4-CANH
4-CANL
3-NC
3-NC
3-CANH
2-NC
2-NC
2-DI IN-
1-NC
1-NC
1-DI IN+
MRDID
Para1
120 Ohm
ON OFF
4 6 8
IN- D2/6 D4/8 REF
1OD753
21MOC7/3D5/1D+NI
NO1 COM1
2araPSMBreteM
DO2
1 2
NO2 COM2
and Generator Control.

RJ45 Terminal Connection (METER, BMS)
1
2
3
2 3
5
4
1
Step 7 Data Transfer Stick (DTS)
© 2023 Hoymiles Power Electronics Inc. All rights reserved. 10
Hybrid Inverter Quick Installation Guide
3
4
12
1
2
M3
0.6-0.8 N·m
6
3
2
1
M3
0.6-0.8 N·m
40 mm
6-7 N·m
WIFI and 4G Connection

4
13
28-NC
7-NC
6-RX-
5-NC
4-NC
3-RX+
2-TX-
1-TX+
PARA1
0.8-1.5 N·m
0.5-0.8 N·m
2
1
5
5
12
3
6
421
Hybrid Inverter Quick Installation Guide
11
3
2
M3
0.6-0.8 N·m
1
1
2
6 DTS Online Setting
1. Search “Hoymiles” in the App Store (iOS) or the Play Store (Android), or scan the QR code to download the Hoymiles
Installer App.
2. Open the app and log in with your installer account and password. For new Hoymiles installers, please apply for
an installer account from your distributor in advance.
Ethernet Connection

(b) Select the DTS’s wireless network and click on “Connect”. (The network name of the DTS consists of DTS and
product serial number, and the default password is ESS12345)
3. Use the App to connect to the DTS.
(a) Open the Installer App on smartphone/tablet and log in. Click on “O&M” at the bottom of the page, and then
click on “Network Configuration”.
2
1
2
3
4
1
Hybrid Inverter Quick Installation Guide
© 2023 Hoymiles Power Electronics Inc. All rights reserved. 12

13
Hybrid Inverter Quick Installation Guide
4. Network configuration.
(a) Upon successful connection, click on “Network Config” again and access the Network Configuration page.
(b) Select the router Wi-Fi and enter the password.
(c) Click on “Send to DTU”.
5. Check the DTS indicator for a solid blue light, which signifies a successful connection.
The network configuration takes about 1 minute, please be patient. If the network is not connected, please check
the internet as instructed.
2
1
1

Hybrid Inverter Quick Installation Guide
14
7 System Commissioning of Wireless Access Point (AP) Connection
1. Connect the wireless network of DTU. Open the App, choose “Toolkit → Generator Setting”, click the corresponding
button according to whether the device connected to the GEN port is “PV Generator” or “Diesel Generator”, and then
click “Save”. (The default option is “None”.)
1
2
3
2. Click the “Meter Location“ to configure the grid side meter. The serial number (SN) can be entered manually or
identified through scanning the QR code.If the GEN port is connected with the PV inverter or diesel generator,
the PV side meter also needs to be configured.
1
2
© 2023 Hoymiles Power Electronics Inc. All rights reserved.

Hybrid Inverter Quick Installation Guide
Hoymiles Power Electronics Inc.
Add: Floor 6-10, Building 5, 99 Housheng Road, Gongshu District,
Hangzhou 310015, P. R. China
Tel: [phone]
Email: [email protected]
[email protected]
www.hoymiles.com
User Manual in the QR code or at
www.hoymiles.com/resources/download/
AP040643
2. Click the “Meter Location“ to configure the grid side meter. The serial number (SN) can be entered manually or
3. Click on “O&M → Toolkit”, access the Overview page and click the “Self-check”. The self check can be completed
after PV, battery, grid, EPS and GEN are properly connected.
1
2
3