HP DF1000A3 User manual

HP df300 Series
HP df300 Série
HP df300 Series
Digital Picture Frame
Cadre Photo Numérique
Marco de Fotos Digital
User Manual
Manuel de l’Utilisateur
Manual del usuario
Revision 1.0a

2
ENGLISH
3
FCC Compliance Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, only use shielded interface cables when
connecting to computer or peripheral devices. Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

2
3
ENGLISH
Table of Contents
FCC Compliance Statement
What’s in the Box?
Getting Started
Initial Setup
Setup Menu
Key Features
Picture Options
Specifications
Frequently Asked Questions
Cleaning and Care Tips
Getting Help
2
4
5
7
9
11
12
16
17
18
19

4
ENGLISH
5
Qty Item Image
1 3.5” Digital Picture Frame
1Universal Power Adapter
(5V, 0.5A, 100/240 switching)
1 USB 2.0 Cable
1 User Manual
1 Warranty Document
IMPORTANT: Please keep this document for
technical support contact information.
1 Declaration of Conformity
1 Leather Carrying Case
What’s in the Box?

4
5
ENGLISH
1. The digital picture frame has basic control buttons on the top of the frame as illustrated
below.
2. Unfold the attached stand to its extended position. Attach the USB cable to the AC adapter.
Connect the mini connector of the cable to the digital picture frame, and plug the adapter
into a wall power outlet as illustrated below. The picture frame will automatically power
on and begin charging the internal battery. Please allow 2 to 3 hours for a full internal
battery charge.
Power
Options Left/Previous
Right/Next
Getting Started

6
ENGLISH
7
3. If the frame did not automatically power on, press and hold the button on the top of
the frame for 3 to 5 seconds. The df300 Digital Picture Frame is preloaded with pictures
that illustrate the basic features of this product and a slideshow will begin in a few seconds.
If you wish to eventually delete these pictures from the internal memory, please reference
the PICTURE OPTIONS section of this manual.
4. If you wish to immediately view your own pictures, insert a SD memory card containing
desired pictures into the card slot. In a few seconds, a slideshow of your pictures will
begin. Note: Memory card must be orientated correctly as illustrated below. Push the
memory card into the slot until it is locked into position.
5. To turn the picture frame off, press and hold the button for 3 to 5 seconds.

6
7
ENGLISH
1. Power on the picture frame and allow the picture slideshow to begin. Press the button
to view the Memory Source Screen as illustrated below.
2. Press and hold the button until the SETUP MENU is displayed as illustrated below.
3. Use the and buttons to highlight the desired setting. Press the button to select the
setting options.
Initial Setup

8
ENGLISH
9
4. Continue to use the and buttons to highlight the desired option. Press the button
to select the desired option.
5. Press the button to return to the SETUP MENU. Press the button again to exit the
SETUP MENU and return to the Memory Source Screen.
6. Use the and buttons to highlight the desired memory source. Press the button
to select the desired memory source. This will begin a slideshow with pictures from the
selected memory source.

8
9
ENGLISH
Option Description
Display Image Size
Select “ORIGINAL” to display pictures with their original properties.
Display picture in full height in normal aspect ratios. Some picture may
not fill the screen, and leave space on both sides. Select “OPTIMAL” to
allow the frame to display pictures with optimized properties. Picture(s)
will enlarge to fit the full width of the screen.
The factory default option is “ORIGINAL”.
Slideshow
Transition
Choose from 6 options and select the preferred transition. Options are:
Normal, Random, Top_Bottom, Curtain, Open_Door, and Cross_Comb.
The default option is set to “RANDOM”.
Slideshow Speed Select the desired picture display length. Options are: 5 seconds, 10 seconds, 30 seconds.
The default option is 5 seconds.
Language Choose from 7 On Screen Display languages. Options are: English, German, French, Spanish, Portuguese, Italian, and Dutch.
The factory default is English .
Connect to PC Select this option when the frame is connected to the PC to switch to file transfer mode. In this mode, you will be able to access the SD/SDHC/
MMC card.
Setup Menu

10
ENGLISH
11
Option Description
Power Saving
This feature will automatically turn off the LCD on the HP digital picture
frame to save valuable energy. You can choose from 4 settings. Options
are: 5 minutes, 10 minutes, 30 minutes, or No Power Saving.
If you want to turn on the LCD, press any key on the photo frame.
The factory default is set to No Power Saving.
Factory Default If you wish to restore ALL the settings to the factory default, press the
button.

10
11
ENGLISH
Feature
Picture slideshow
• Automatic picture transition with 6 different variations.
Multiple picture viewing options
• View individual pictures in Browse mode (see later section)
• Copy pictures from an SD to internal memory without a PC connection
• Zoom and rotate individual pictures
Brightness, contrast, tint, and color adjustments in photo browse mode.
Add pictures from a SD card to the internal memory.
Rechargeable internal battery power for portable viewing.
• Recharge by AC adapter or PC/Laptop USB connection
• Up to 2 hours of battery power between charges.
Power saving mode
• Choose between 4 different settings.
Key Features

12
ENGLISH
13
Slideshow modes
Slideshow mode will begin automatically a few seconds after the frame is powered on or when
an external memory card is inserted.
Browse mode
To exit slideshow mode, press the button once. A pause symbol will be briey displayed
in the upper right of the screen. This allows forward and previous picture viewing by pressing
the and arrow buttons.
Thumbnail mode
To view pictures in a thumbnail mode, press the button twice when in slideshow or once
when in browse mode. See illustrated below for thumbnail example.
Use the and buttons to navigate to a picture. Press the button to view the selected
picture.
Picture Options

12
13
ENGLISH
Picture Rotation
While in slideshow or browse mode, press and hold the button until the PICTURE
OPTIONS menu is displayed as illustrated below.
Press the button to rotate the displayed picture. Each press of this button will rotate the
picture by 90 degrees in a clockwise motion.
Press the button to remove the PICTURE OPTIONS menu.
Picture Zoom
While in browse mode, press and hold the button until the PICTURE OPTIONS menu is
displayed. Pictures can be zoomed to 4X by pressing the button. Each press of this button
will increase the zoom by 1X until 4X. At 4X, press this button once to return to the original
view. Note: if a picture is zoomed while in slideshow mode, the frame will automatically enter
into photo browse mode.
Press the button to remove the PICTURE OPTIONS menu.

14
ENGLISH
15
Copying pictures onto internal memory
Pictures can only be copied onto the df300 frame’s internal memory from a Secure Digital (SD
or SDHC) or MMC memory card.
1. Insert an SD/SDHC/MMC memory card with the desired pictures into the frame’s
memory card slot.
2. Power on the picture frame and a slideshow from the SD/SDHC/MMC memory card
will automatically begin in a few seconds. Press the button to switch to browse
mode or thumbnail mode.
3. Use the or arrow buttons to navigate to the picture you wish to copy.
4. Press and hold the button until the PICTURE OPTIONS menu is displayed.
5. Use the arrow button to highlight the COPY PHOTO option.
6. Press the button to begin copying the picture to internal memory. Once the picture
has been copied, an Ok text box will be briefly displayed.
7. Press the button to remove the PICTURE OPTIONS menu.
8. If you wish to copy more pictures, simply repeat the above steps until finished.

14
15
ENGLISH
Deleting pictures from internal memory
Pictures can only be deleted from the df300 frame’s internal memory.
1. Power down the picture frame.
2. If applicable, remove the memory card from the slot. This is done by pushing the card
further into the slot until the card latch mechanism is released. The card is now in an
unlocked position. Remove the memory card.
3. Turn on the frame and allow the slideshow of pictures on the internal memory to begin.
Press the button once to stop the slideshow.
4. Use the and arrow buttons to navigate the picture you wish to delete.
5. Press and hold the button until the PICTURE OPTIONS menu is displayed.
6. Use the arrow button to highlight the DELETE PHOTO option.
7. Press the button to delete the picture from the internal memory. Once the picture
has been deleted, an Ok text box will be briey displayed.
8. If you wish to delete the next displayed image, press the button again. Repeat
this step until nished
9. Press the button to remove the PICTURE OPTIONS menu.
10. If you wish to delete more pictures, simply repeat the above steps until nished.

16
ENGLISH
17
Adjust LCD Color
While in browse mode, press and hold the button until the PICTURE OPTIONS menu is
displayed.
1. Use the arrow button to highlight the Adjust LCD Color option.
2. Press the button to display the Adjustment options.
3. The Brightness option will be highlighted. Use the or arrow buttons to adjust
screen brightness. Adjust to the desired level.
4. Press and hold the or arrow button until the next option is highlighted (Contrast,
Color, and Tint). Again, use the or arrow buttons to adjust the selected option.
5. When finished, press the button to return to the PICTURE OPTIONS menu. Press
the button again to return to Browse mode.

16
17
ENGLISH
Panel Specification
Screen Size 3.5”
Frame Dimension 95 x 77 x 13 (mm)
Aspect ratio 4:3
Resolution 320x240 pixels
Power
External AC Power Adapter +5V, 0.5A
Connectivity
USB Ports 1- Mini USB 2.0 for recharging the internal battery via AC adapter or PC/Laptop
USB connection.
Storage/Media
Internal memory Up to 45 photos
Supported Memory cards
Memory cards slot Secure Digital (SD 2.0, SDHC) and MMC
Media Files Supported
Picture file formats JPEG - (Base line only)
Supported Languages
On-Screen Display English, French, Spanish, Italian, German, Dutch, & Portuguese
Specifications

18
ENGLISH
19
Question Answer
Why can’t I display some of my Pictures? Some picture/image file formats are not supported. Please
refer to the specifications.
Why is my picture frame not responding to any
button selections? Use a small paper clip or other tool to press the RESET button located on the back of the frame under the folding stand.
How long does it take to fully charge the Digital
Picture Frame’s internal battery? Approximately 3 hours.
How long will the internal battery supply power to
the frame? Up to 2 hours.
Can I overcharge the internal battery? No
How long will the internal battery last? Up to 2 years
Can I replace the internal battery if it expires? No
Can I delete pictures from a SD memory card using
the df300 Digital Picture Frame? No. Only pictures on the internal memory can be deleted.
Can I delete pictures from internal memory? Yes, refer to the Picture Options section of this document.
How can I switch to the internal memory? Remove the external memory card or reference the Initial Setup
section of this manual.
How can I find the latest information/FAQs about
my HP Digital Picture Frame? Visit www.hp.com/support for more details and the latest information.
Frequently Asked Questions

18
19
ENGLISH
√ Please power off the HP Digital Picture Frame before cleaning.
√ DO NOT push on the screen too firmly.
√ DO NOT spray or pour liquid cleaning agents directly on the screen or frame.
√ DO NOT use ammonia, alcohol, or abrasive detergent cleaning agents.
Cleaning the Screen:
1. Wipe screen with a clean, soft, lint-free cloth to remove dust and loose particles.
2. If further cleaning is required, apply an appropriate cleaning agent (approved
for LCD displays) to a clean, soft, lint-free cloth and wipe the screen.
• NOTE: do not apply too much pressure on the screen to avoid damaging it.
Cleaning the Frame and Backing:
1. Use a clean, soft, lint-free cloth to remove dust and loose particles.
2. If desired, apply an appropriate cleaning agent to a clean, soft, lint-free cloth
and wipe the appropriate surfaces.
Cleaning and Care Tips

20
ENGLISH
21
Should you have a technical support question
or your HP Digital Picture frame requires service
within the warranty period, please contact the
original point of purchase or an authorized
HP reseller in your country. If service is not
available at those locations, please contact an
HP Branded Product warranty agent from the
support contact list provided below. A service
agent will work with you to troubleshoot your
issue and if necessary, issue a Return Material
Authorization (RMA) number in order to replace
your HP Branded Product. For warranty claims,
you will be required to provide a copy of
your original dated sales receipt as proof of
purchase and the issued RMA number. You
will be responsible for shipping charges when
shipping the product to the service center. The
service agent will provide you with an address
and you will also be responsible for any
shipping charges to the warranty service center.
Once your product is received by this service
center, a replacement unit will be shipped back
to you typically within 5 business days.
Email Support
Language Email Address
Dutch [e-mail]
Chinese [e-mail]
[e-mail]
English [e-mail]
Français [e-mail]
Deutsch [e-mail]
Italiano [e-mail]
Japanese [e-mail]
Korean [e-mail]
Portuguese [e-mail]
Espanol [e-mail]
Svenska [e-mail]
Getting Help