HP df301 Series User manual

HP df301 Series
Digital Picture Frame
Cadre Photo Numérique
Marco de Fotos Digital
Digitaler Bilderrahmen
Cornice digitale
Цифровая фоторамка
Ramka cyfrowa
Porta-Retratos Digital
Digitale fotolijst
Digitaler Bilderrahmen
User Manual
Manuel de l’Utilisateur
Manual del usuario
Benutzerhandbuch
Manuale dell'utente
Руководство пользователя
Instrukcja obsługi
Manual do Utilizador
Gebruikershandleiding
Brugervejledning
Revision 1.0a

1
ENGLISH
FCC Compliance Statement
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, only use shielded interface
cables when connecting to computer or peripheral devices. Any changes
or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

2
ENGLISH
Table of Contents
FCC Compliance Statement
What’s in the Box?
Getting Started
Initial Setup
Setup Menu
Key Features
Picture Options
Specifications
Frequently Asked Questions
Cleaning and Care Tips
Getting Help
1
3
4
6
8
10
11
16
17
18
19

3
ENGLISH
Qty Item Image
1 3.5” Digital Picture Frame
1Universal Power Adapter
(5V, 0.5A, 100/240 switching)
1 USB 2.0 Cable
1 User Manual
1 Warranty Document
IMPORTANT: Please keep this
document for technical support
contact information.
What’s in the Box?

4
ENGLISH
1. The digital picture frame has basic control buttons on the top of the
frame as illustrated below.
2. Unfold the attached stand to its extended position. Attach the USB
cable to the AC adapter. Connect the mini connector of the cable
to the digital picture frame, and plug the adapter into a wall power
outlet as illustrated below. The picture frame will automatically
power on and begin charging the internal battery. Please allow 2 to
3 hours for a full internal battery charge.
* On some models the SD card slot is located next to the USB slot.
Power
Options Left/Previous
Right/Next
Getting Started

5
ENGLISH
3. If the frame did not automatically power on, press and hold the
button on the top of the frame for 3 to 5 seconds. The df300
Digital Picture Frame is preloaded with pictures that illustrate the
basic features of this product and a slideshow will begin in a few
seconds. If you wish to eventually delete these pictures from the
internal memory, please reference the PICTURE OPTIONS section of
this manual.
4. If you wish to immediately view your own pictures, insert a SD
memory card containing desired pictures into the card slot. In a few
seconds, a slideshow of your pictures will begin. Note: Memory card
must be orientated correctly as illustrated below. Push the memory
card into the slot until it is locked into position.
* On some models the SD card slot is located next to the USB slot.
5. To turn the picture frame off, press and hold the button for 3
to 5 seconds.

6
ENGLISH
1. Power on the picture frame and allow the picture slideshow to
begin. Press the button to view the Memory Source Screen as
illustrated below.
2. Press and hold the button until the SETUP MENU is displayed as
illustrated below.
Initial Setup

7
ENGLISH
3. Use the and buttons to highlight the desired setting. Press the
button to select the setting options.
4. Continue to use the and buttons to highlight the desired
option. Press the button to select the desired option.
5. Press the button to return to the SETUP MENU. Press the
button again to exit the SETUP MENU and return to the Memory
Source Screen.
6. Use the and buttons to highlight the desired memory source.
Press the button to select the desired memory source. This will
begin a slideshow with pictures from the selected memory source.

8
ENGLISH
Option Description
Display Image Size
Select “ORIGINAL” to display pictures with
their original properties. Display picture in full
height in normal aspect ratios. Some picture
may not fill the screen, and leave space on both
sides. Select “OPTIMAL” to allow the frame
to display pictures with optimized properties.
Picture(s) will enlarge to fit the full width of the
screen.
The factory default option is “ORIGINAL”.
Slideshow Transition
Choose from 6 options and select the preferred
transition. Options are: Normal, Random, Top_
Bottom, Curtain, Open_Door, and Cross_Comb.
The default option is set to “RANDOM”.
Slideshow Speed
Select the desired picture display length.
Options are: 5 seconds, 10 seconds, 30
seconds.
The default option is 5 seconds.
Language
Choose from 7 On Screen Display languages.
Options are: English, German, French, Spanish,
Portuguese, Italian, and Dutch.
The factory default is English .
Setup Menu

9
ENGLISH
Option Description
Connect to PC
Select this option when the frame is connected to
the PC to switch to file transfer mode. In this mode,
you will be able to access the SD/SDHC/MMC
card.
Power Saving
This feature will automatically turn off the LCD on
the HP digital picture frame to save valuable energy.
You can choose from 4 settings. Options are: 5
minutes, 10 minutes, 30 minutes, or No Power
Saving.
If you want to turn on the LCD, press any key on the
photo frame.
The factory default is set to No Power Saving.
Factory Default If you wish to restore ALL the settings to the factory
default, press the button.

10
ENGLISH
Feature
Picture slideshow
• Automatic picture transition with 6 different variations.
Multiple picture viewing options
• View individual pictures in Browse mode (see later section)
• Copy pictures from an SD to internal memory without a PC
connection
• Zoom and rotate individual pictures
Brightness, contrast, tint, and color adjustments in photo browse mode.
Add pictures from a SD card to the internal memory.
Rechargeable internal battery power for portable viewing.
• Recharge by AC adapter or PC/Laptop USB connection
• Up to 2 hours of battery power between charges.
Power saving mode
• Choose between 4 different settings.
Key Features

11
ENGLISH
Slideshow modes
Slideshow mode will begin automatically a few seconds after the frame
is powered on or when an external memory card is inserted.
Browse mode
To exit slideshow mode, press the button once. A pause symbol
will be briefly displayed in the upper right of the screen. This allows
forward and previous picture viewing by pressing the and arrow
buttons.
Thumbnail mode
To view pictures in a thumbnail mode, press the button twice when
in slideshow or once when in browse mode. See illustrated below for
thumbnail example.
Use the and buttons to navigate to a picture. Press the
button to view the selected picture.
Picture Options

12
ENGLISH
Picture Rotation
While in slideshow or browse mode, press and hold the button
until the PICTURE OPTIONS menu is displayed as illustrated below.
Press the button to rotate the displayed picture. Each press of this
button will rotate the picture by 90 degrees in a clockwise motion.
Press the button to remove the PICTURE OPTIONS menu.
Picture Zoom
While in browse mode, press and hold the button until the PICTURE
OPTIONS menu is displayed. Pictures can be zoomed to 4X by pressing
the button. Each press of this button will increase the zoom by 1X
until 4X. At 4X, press this button once to return to the original view.
Note: if a picture is zoomed while in slideshow mode, the frame will
automatically enter into photo browse mode.
Press the button to remove the PICTURE OPTIONS menu.

13
ENGLISH
Copying pictures onto internal memory
Pictures can only be copied onto the df300 frame’s internal memory from
a Secure Digital (SD or SDHC) or MMC memory card.
1. Insert an SD/SDHC/MMC memory card with the desired pictures into
the frame’s memory card slot.
2. Power on the picture frame and a slideshow from the SD/SDHC/
MMC memory card will automatically begin in a few seconds. Press
the button to switch to browse mode or thumbnail mode.
3. Use the or arrow buttons to navigate to the picture you wish to
copy.
4. Press and hold the button until the PICTURE OPTIONS menu is
displayed.
5. Use the arrow button to highlight the COPY PHOTO option.
6. Press the button to begin copying the picture to internal
memory. Once the picture has been copied, an Ok text box will be
briefly displayed.
7. Press the button to remove the PICTURE OPTIONS menu.
8. If you wish to copy more pictures, simply repeat the above steps until
finished.

14
ENGLISH
Deleting pictures from internal memory
Pictures can only be deleted from the df300 frame’s internal memory.
1. Power down the picture frame.
2. If applicable, remove the memory card from the slot. This is done by
pushing the card further into the slot until the card latch mechanism
is released. The card is now in an unlocked position. Remove the
memory card.
3. Turn on the frame and allow the slideshow of pictures on the internal
memory to begin. Press the button once to stop the slideshow.
4. Use the and arrow buttons to navigate the picture you wish to
delete.
5. Press and hold the button until the PICTURE OPTIONS menu is
displayed.
6. Use the arrow button to highlight the DELETE PHOTO option.
7. Press the button to delete the picture from the internal memory.
Once the picture has been deleted, an Ok text box will be briefly
displayed.
8. If you wish to delete the next displayed image, press the button
again. Repeat this step until finished
9. Press the button to remove the PICTURE OPTIONS menu.

15
ENGLISH
10. If you wish to delete more pictures, simply repeat the above steps
until finished.
Adjust LCD Color
While in browse mode, press and hold the button until the PICTURE
OPTIONS menu is displayed.
1. Use the arrow button to highlight the Adjust LCD Color option.
2. Press the button to display the Adjustment options.
3. The Brightness option will be highlighted. Use the or arrow
buttons to adjust screen brightness. Adjust to the desired level.
4. Press and hold the or arrow button until the next option is
highlighted (Contrast, Color, and Tint). Again, use the or
arrow buttons to adjust the selected option.
5. When finished, press the button to return to the PICTURE
OPTIONS menu. Press the button again to return to Browse
mode.

16
ENGLISH
Panel Specification
Screen Size 3.5”
Frame Dimension 95 x 77 x 13 (mm)
Aspect ratio 4:3
Resolution 320x240 pixels
Power
External AC Power Adapter +5V, 0.5A
Connectivity
USB Ports 1- Mini USB 2.0 for recharging the internal battery via AC adapter or
PC/Laptop USB connection.
Storage/Media
Internal memory Up to 45 photos
Supported Memory cards
Memory cards slot Secure Digital (SD 2.0, SDHC) and
MMC
Media Files Supported
Picture file formats JPEG - (Base line only)
Supported Languages
On-Screen Display English, French, Spanish, Italian,
German, Dutch, and Portuguese
Specifications

17
ENGLISH
Question Answer
Why can’t I display some of my
Pictures? Some picture/image file formats are not supported. Please refer to the specifications.
Why is my picture frame not
responding to any button
selections?
Use a small paper clip or other tool to press
the RESET button located on the back of the
frame under the folding stand.
How long does it take to fully
charge the Digital Picture Frame’s
internal battery? Approximately 3 hours.
How long will the internal battery
supply power to the frame? Up to 2 hours.
Can I overcharge the internal
battery? No
How long will the internal battery
last? Up to 2 years
Can I replace the internal battery
if it expires? No
Can I delete pictures from a SD
memory card using the df300
Digital Picture Frame?
No. Only pictures on the internal memory
can be deleted.
Can I delete pictures from internal
memory? Yes, refer to the Picture Options section of this document.
How can I switch to the internal
memory?
Remove the external memory card or
reference the Initial Setup section of this
manual.
How can I find the latest
information/FAQs about my HP
Digital Picture Frame?
Visit www.hp.com/support for more details
and the latest information.
Frequently Asked Questions

18
ENGLISH
√ Please power off the HP Digital Picture Frame before cleaning.
√ DO NOT push on the screen too firmly.
√ DO NOT spray or pour liquid cleaning agents directly on the
screen or frame.
√ DO NOT use ammonia, alcohol, or abrasive detergent cleaning
agents.
Cleaning the Screen:
1. Wipe screen with a clean, soft, lint-free cloth to remove
dust and loose particles.
2. If further cleaning is required, apply an appropriate
cleaning agent (approved for LCD displays) to a clean,
soft, lint-free cloth and wipe the screen.
• NOTE: do not apply too much pressure on the screen to
avoid damaging it.
Cleaning the Frame and Backing:
1. Use a clean, soft, lint-free cloth to remove dust and
loose particles.
2. If desired, apply an appropriate cleaning agent to a
clean, soft, lint-free cloth and wipe the appropriate
surfaces.
Cleaning and Care Tips

19
ENGLISH
Should you have a
technical support
question or your HP
Digital Picture frame
requires service
within the warranty
period, please contact
the original point
of purchase or an
authorized HP reseller
in your country. If
service is not available
at those locations,
please contact an
HP Branded Product
warranty agent from
the support contact
list provided below.
A service agent will
work with you to troubleshoot your issue and if necessary, issue a Return
Material Authorization (RMA) number in order to replace your HP
Branded Product. For warranty claims, you will be required to provide
a copy of your original dated sales receipt as proof of purchase and
the issued RMA number. You will be responsible for shipping charges
when shipping the product to the service center. The service agent will
provide you with an address and you will also be responsible for any
shipping charges to the warranty service center. Once your product is
received by this service center, a replacement unit will be shipped back
to you typically within 5 business days.
Email Support
Language Email Address
Dutch [e-mail]
Chinese [e-mail]
[e-mail]
English [e-mail]
Français [e-mail]
Deutsch [e-mail]
Italiano [e-mail]
Japanese [e-mail]
Korean [e-mail]
Portuguese [e-mail]
Espanol [e-mail]
Svenska [e-mail]
Getting Help