HP Vectra VL6 6 User manual

Etherlink XL PCI Network Interface
Card
3C900
Installation Guide

Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental
orconsequentialdamagesinconnectionwiththefurnishing,performance,oruse
of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent
of Hewlett-Packard Company.
Microsoft®, Windows®and MS-DOS®are registered trademarks of Microsoft
Corporation.
MMXTMis a trademark of Intel Corporation.
Pentium® is a registered trademark of Intel Corporation.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France

1 Connecting to a Netware 3.12 Server
Windows for Workgroups
1 Connecting to a Netware 3.12 Server
Windows for
WorkgroupsRequirements
•HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
•3COM Etherlink 3C900 Ethernet card and drivers disk ver 2.1.
DOS ODI - File Name:3C90X.COM Size: 59KBDate: 12/18/96
•DOS and MS-Windows for Workgroups 3.11 media.
•Novell Netware server that supports Net BEUI, NWLink IPX/SPX, and
NWLink NetBIOS transfer protocols.
•Netware client for DOS and MS-Windows.
Device Configuration
•Network Driver Optimization Normal
•Full Duplex Disabled
•Boot PROM Disabled
•Media Type 10BASE-T
•I/O Base Address FCC0h (PCI)
•Interrupt Request Level 9 (PCI)
Procedure
1With the HP Vectra turned off install the 3COM Etherlink III 3C900
adapter card into a PCI slot.
2Power on the machine and allow it to boot to a DOS prompt.
3Insert the 3COM drivers diskette (ver. 2.1 downloaded from 3COM’s
website) and execute 3C90XCFG.EXE.
4Select “CONFIGURE NIC,” and verify the resource settings listed above
under the heading “Device Configuration.”
5If changes are required, save those changes and exit.
6Removethe3comcardsdriverdisketteandinsertNetwareclientforDOS
and MS-Windows disk 1.

1 Connecting to a Netware 3.12 Server
Windows for Workgroups
7Execute INSTALL.EXE and set lines 1-5 as listed below;
•C:\NWCLIENT
•YES
•YES
C:\WINDOWS
•NO
•3COM Etherlink XL/Fast Etherlink XL Family.
8Highlight option 6 to continue with installation.
9When prompted, insert the corresponding disks to complete file transfer
and driver installation.
10 Whenthe install utilityis finished, press<CRTL><ALT><DEL> to restart
the machine.
11 After windows loads, open the “NETWORK” folder and double-click the
“NETWORK SETUP” icon.
12 Select “Networks” and verify that “Novell Netware (Workstation Shell 4.0
and above)” is listed under “Install Windows support for the following
network only:” and click on “OK.”

1 Connecting to a Netware 3.12 Server
Windows 95 SR2
Windows 95 SR2Requirements
•HP Vectra with Windows 95 SR2 installed.
•3COM Etherlink 3C900 Ethernet card and drivers disk ver 2.1.
•File Name: OEMSETUP.INF Size: 41KBDate: 3/14/97
•Windows 95 SR2 media. (If you have an HP preloaded HDD, the media is
located at C:\Masters\Win95\System\Cabs\)
•Novell Netware 3.12 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
Device Configuration
•Network Driver Optimization Normal
•Full Duplex Disabled
•Boot PROM Disabled
•Media Type 10BASE-T
•I/O Base Address FCC0h (PCI)
•Interrupt Request Level 9 (PCI)
Procedure
1With the HP Vectra turned off install the 3COM Etherlink III 3C900
adapter card into a PCI slot.
2Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.
3Insert the 3COM drivers diskette (ver. 2.1 downloaded from 3COM’s
website) and execute 3C90XCFG.EXE.
4Select “CONFIGURE NIC,” and verify the resource settings listed above
under the heading “Device Configuration.”
5If changes are required, save those changes and exit.
6Remove the 3com cards driver diskette and restart the machine.
7Windows 95 SR2 should automatically recognize the 3COM 3C900
ethernet card.
8With “PCI Ethernet Controller” listed, click on “Next.”
9Click on “Other Locations” and insert the 3C900 driver’s disk 1 of 2.

1 Connecting to a Netware 3.12 Server
Windows 95 SR2
10 Set the path to “A:\” and click on “OK.” (If you have a Hewlett-Packard
pre-loaded HDD, set the path statement to “C:\LANDRV\3C900\Disk1\”)
11 “3Com Etherlink XL TPO 10Mb Ethernet Adapter” should now be listed.
Click on “Finish.”
12 When prompted, insert the 3C900 driver’s disk 2 of 2 and click on “OK.”
13 In the “Copying Files…” window, the path should read “A:\” (If you have
an HP pre-loaded HDD, set the path statement to
“C:\LANDRV\3C900\Disk2\”)
14 Click on “OK” to continue the installation.
15 Click on “OK” in order to provide Computer and Workgroup names.
16 At the “Network” dialogue box, click on the “Identification” folder.
17 Enter your “Computer Name,” “Workgroup,” and “Computer
Description.” And click on “Close.” (If you do not have a Computer name,
Workgroup name and Computer description, contact your network
administrator)
18 At the “Insert Disk” notification, click on “OK.”
19 Set the path to your Windows 95 SR2 media and click on “OK.”
(If you have an HP preloaded HDD, the media is located at
C:\Masters\Win95\System\Cabs\)
20 When prompted, insert the 3C900 driver’s disk 2 of 2 and click on “OK.”
21 Set the path to “A:\” and click on “OK.” (If you have an HP pre-loaded
HDD, set the path statement to “C:\LANDRV\3C900\Disk2\”)
22 Click on “YES” to complete installation and restart the machine.

2 Connecting to a Netware 4.11 Server
Windows for Workgroups
2 Connecting to a Netware 4.11 Server
Windows for
WorkgroupsRequirements
•HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
•3COM Etherlink 3C900 Ethernet card and drivers disk ver 2.1.
DOS ODI - File Name: 3C90X.COM Size: 59KB Date: 12/18/96
•DOS and MS-Windows for Workgroups 3.11 media.
•Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
•Netware client for DOS and MS-Windows.
Device Configuration
•Network Driver Optimization Normal
•Full Duplex Disabled
•Boot PROM Disabled
•Media Type 10BASE-T
•I/O Base Address FCC0h (PCI)
•Interrupt Request Level 9 (PCI)
Procedure
1With the HP Vectra turned off install the 3COM Etherlink III 3C900
adapter card into a PCI slot.
2Power on the machine and allow it to boot to a DOS prompt.
3Insert the 3COM drivers diskette (ver. 2.1 downloaded from 3COM’s
website) and execute 3C90XCFG.EXE.
4Select “CONFIGURE NIC,” and verify the resource settings listed above
under the heading “Device Configuration.”
5If changes are required, save those changes and exit.
6Removethe3comcardsdriverdisketteandinsertNetwareclientforDOS
and MS-Windows disk 1.

2 Connecting to a Netware 4.11 Server
Windows for Workgroups
7Execute INSTALL.EXE and set lines 1-5 as listed below;
•C:\NWCLIENT
•YES
•YES
C:\WINDOWS
•NO
•3COM Etherlink XL/Fast Etherlink XL Family.
8Highlight option 6 to continue with installation.
9When prompted, insert the corresponding disks to complete file transfer
and driver installation.
10 Whenthe install utilityis finished, press<CRTL><ALT><DEL> to restart
the machine.
11 After windows loads, open the “NETWORK” folder and double-click the
“NETWORK SETUP” icon.
12 Select “Networks” and verify that “Novell Netware (Workstation Shell 4.0
and above)” is listed under “Install Windows support for the following
network only:” and click on “OK.”

2 Connecting to a Netware 4.11 Server
Windows 95 SR2
Windows 95 SR2Requirements
•HP Vectra with Windows 95 SR2 installed.
•3COM Etherlink 3C900 Ethernet card and drivers disk ver 2.1.
•File Name: OEMSETUP.INF Size: 41KBDate: 3/14/97
•Windows 95 SR2 media. (If you have an HP preloaded HDD, the media is
located at C:\Masters\Win95\System\Cabs\)
•Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
Device Configuration
•Network Driver Optimization Normal
•Full Duplex Disabled
•Boot PROM Disabled
•Media Type 10BASE-T
•I/O Base Address FCC0h (PCI)
•Interrupt Request Level 9 (PCI)
Procedure
1With the HP Vectra turned off install the 3COM Etherlink III 3C900
adapter card into a PCI slot.
2Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.
3Insert the 3COM drivers diskette (ver. 2.1 downloaded from 3COM’s
website) and execute 3C90XCFG.EXE.
4Select “CONFIGURE NIC,” and verify the resource settings listed above
under the heading “Device Configuration.”
5If changes are required, save those changes and exit.
6Remove the 3com cards driver diskette and restart the machine.
7Windows 95 SR2 should automatically recognize the 3COM 3C900
ethernet card.
8With “PCI Ethernet Controller” listed, click on “Next.”
9Click on “Other Locations” and insert the 3C900 driver’s disk 1 of 2.

2 Connecting to a Netware 4.11 Server
Windows 95 SR2
10 Set the path to “A:\” and click on “OK.” (If you have a Hewlett-Packard
pre-loaded HDD, set the path statement to “C:\LANDRV\3C900\Disk1\”)
11 “3Com Etherlink XL TPO 10Mb Ethernet Adapter” should now be listed.
Click on “Finish.”
12 When prompted, insert the 3C900 driver’s disk 2 of 2 and click on “OK.”
13 In the “Copying Files…” window, the path should read “A:\” (If you have
an HP pre-loaded HDD, set the path statement to
“C:\LANDRV\3C900\Disk2\”)
14 Click on “OK” to continue the installation.
15 Click on “OK” in order to provide Computer and Workgroup names.
16 At the “Network” dialogue box, click on the “Identification” folder.
17 Enter your “Computer Name,” “Workgroup,” and “Computer
Description.” And click on “Close.” (If you do not have a Computer name,
Workgroup name and Computer description, contact your network
administrator)
18 At the “Insert Disk” notification, click on “OK.”
19 Set the path to your Windows 95 SR2 media and click on “OK.” (If you
have an HP preloaded HDD, the media is located at
C:\Masters\Win95\System\Cabs\)
20 When prompted, insert the 3C900 driver’s disk 2 of 2 and click on “OK.”
21 Set the path to “A:\” and click on “OK.” (If you have an HP pre-loaded
HDD, set the path statement to “C:\LANDRV\3C900\Disk2\”)
22 Click on “YES” to complete installation and restart the machine.