HP ProLiant DL160 Gen9 User manual

HP ProLiant DL160 Gen9 Server
User Guide
Abstract
This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the
servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
Part Number: 775786-003
March 2015
Edition: 3

© Copyright 2015 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Linux®is the registered trademark of Linus Torvalds in the U.S. and other countries.
Microsoft®, Windows®, and Windows Server® are U.S. registered trademarks of the Microsoft group of companies.
microSD®is a trademark or a registered trademark of SD-3C in the United States, other countries or both.
Red Hat®is a registered trademark of Red Hat, Inc. in the United States and other countries.
VMware®is a registered trademark or trademark of VMware, Inc. in the United States and/or other jurisdictions.

Contents 3
Contents
Component identification............................................................................................................... 7
Front panel components ............................................................................................................................. 7
Front panel LEDs and buttons ...................................................................................................................... 8
Front panel LED power fault codes................................................................................................... 10
Rear panel components............................................................................................................................ 10
Rear panel LEDs ...................................................................................................................................... 11
PCIe riser board slot definitions................................................................................................................. 11
System board components........................................................................................................................ 12
DIMM slot locations ....................................................................................................................... 13
System maintenance switch............................................................................................................. 13
NMI functionality........................................................................................................................... 14
Drive numbering ..................................................................................................................................... 14
HP SmartDrive LED definitions ................................................................................................................... 15
Fan locations .......................................................................................................................................... 16
Operations................................................................................................................................. 17
Power up the server ................................................................................................................................. 17
Power down the server............................................................................................................................. 17
Extend the server from the rack ................................................................................................................. 17
Access the product rear panel................................................................................................................... 20
Opening the cable management arm ............................................................................................... 20
Remove the server from the rack................................................................................................................ 20
Remove the security bezel (optional) .......................................................................................................... 21
Remove the access panel.......................................................................................................................... 21
Install the access panel............................................................................................................................. 22
Remove the PCI riser cage ........................................................................................................................ 23
Install the PCI riser cage ........................................................................................................................... 24
Setup......................................................................................................................................... 26
Optional services .................................................................................................................................... 26
Optimum environment.............................................................................................................................. 26
Space and airflow requirements ...................................................................................................... 26
Temperature requirements............................................................................................................... 27
Power requirements ....................................................................................................................... 28
Electrical grounding requirements .................................................................................................... 28
Server warnings and cautions ................................................................................................................... 28
Rack warnings ........................................................................................................................................ 29
Identifying the contents of the server shipping carton.................................................................................... 30
Installing hardware options....................................................................................................................... 30
Installing the server into the rack................................................................................................................ 30
Installing the rack rail hook-and-loop strap.................................................................................................. 34
Installing the operating system................................................................................................................... 35
Powering on and selecting boot options in UEFI Boot Mode.......................................................................... 35
Registering the server............................................................................................................................... 36
Hardware options installation....................................................................................................... 37
Introduction ............................................................................................................................................ 37

Contents 4
Security bezel option ............................................................................................................................... 37
Drive options .......................................................................................................................................... 37
Drive installation guidelines ............................................................................................................ 38
Installing a non-hot-plug drive.......................................................................................................... 38
Installing a hot-plug drive................................................................................................................ 40
Controller options.................................................................................................................................... 41
Installing a storage controller .......................................................................................................... 41
Installing an FBWC module and an HP Smart Storage Battery ............................................................. 43
Drive cable options.................................................................................................................................. 46
Mini-SAS cable options .................................................................................................................. 47
Optical drive option ................................................................................................................................ 50
Redundant fan option .............................................................................................................................. 53
Fan population guidelines............................................................................................................... 54
Installing a hot-swap fan module...................................................................................................... 54
Memory options...................................................................................................................................... 57
HP SmartMemory .......................................................................................................................... 58
Memory subsystem architecture ....................................................................................................... 58
Single-, dual-, and quad-rank DIMMs ............................................................................................... 58
DIMM identification ....................................................................................................................... 59
Memory configurations................................................................................................................... 59
General DIMM slot population guidelines ......................................................................................... 61
Installing a DIMM .......................................................................................................................... 62
Processor option...................................................................................................................................... 63
Secondary PCIe x16 riser option............................................................................................................... 68
FlexibleLOM option ................................................................................................................................. 69
Expansion board options.......................................................................................................................... 72
M.2 SSD enablement option..................................................................................................................... 74
Front USB 3.0 option ............................................................................................................................... 77
Redundant power supply option ................................................................................................................ 80
Dedicated iLO management module option ................................................................................................ 82
Enabling the dedicated iLO management module .............................................................................. 84
HP Trusted Platform Module option ............................................................................................................ 84
Installing the Trusted Platform Module board ..................................................................................... 85
Retaining the recovery key/password .............................................................................................. 86
Enabling the Trusted Platform Module............................................................................................... 87
Cabling ..................................................................................................................................... 88
Cabling overview.................................................................................................................................... 88
Storage cabling ...................................................................................................................................... 88
Four-bay LFF non-hot-plug drive cabling ............................................................................................ 88
Four-bay LFF hot-plug drive cabling.................................................................................................. 89
Eight-bay SFF hot-plug drive cabling ................................................................................................ 90
M.2 SSD cabling .................................................................................................................................... 92
FBWC cabling ........................................................................................................................................ 93
HP Smart Storage Battery cabling.............................................................................................................. 95
FlexibleLOM cabling................................................................................................................................ 95
Power supply cabling............................................................................................................................... 96
Optical drive cabling............................................................................................................................... 97
Front I/O cabling.................................................................................................................................... 98
Front USB 3.0 cabling ............................................................................................................................. 99
Software and configuration utilities ............................................................................................. 100
Server mode ......................................................................................................................................... 100
Product QuickSpecs............................................................................................................................... 100

Contents 5
HP iLO................................................................................................................................................. 100
Active Health System.................................................................................................................... 101
HP RESTful API support for HP iLO ................................................................................................. 102
Integrated Management Log ......................................................................................................... 102
HP Insight Remote Support............................................................................................................ 103
Intelligent Provisioning ........................................................................................................................... 103
HP Insight Diagnostics.................................................................................................................. 104
Erase Utility ................................................................................................................................ 104
Scripting Toolkit for Windows and Linux................................................................................................... 105
HP Service Pack for ProLiant ................................................................................................................... 105
HP Smart Update Manager........................................................................................................... 105
HP UEFI System Utilities.......................................................................................................................... 106
Using HP UEFI System Utilities ....................................................................................................... 106
Flexible boot control .................................................................................................................... 106
Restoring and customizing configuration settings ............................................................................. 107
Secure Boot configuration............................................................................................................. 107
Embedded UEFI shell ................................................................................................................... 108
Embedded Diagnostics option ....................................................................................................... 108
HP RESTful API support for UEFI..................................................................................................... 108
Re-entering the server serial number and product ID ......................................................................... 108
Utilities and features .............................................................................................................................. 109
HP Smart Storage Administrator .................................................................................................... 109
Automatic Server Recovery ........................................................................................................... 109
USB support................................................................................................................................ 109
Redundant ROM support .............................................................................................................. 110
Keeping the system current ..................................................................................................................... 110
Access to HP Support Materials..................................................................................................... 110
Updating firmware or System ROM ............................................................................................... 111
Drivers ....................................................................................................................................... 112
Software and firmware................................................................................................................. 113
Operating System Version Support ................................................................................................ 113
Version control............................................................................................................................ 113
HP operating systems and virtualization software support for ProLiant servers ...................................... 114
HP Technology Service Portfolio .................................................................................................... 114
Change control and proactive notification ...................................................................................... 114
Troubleshooting ........................................................................................................................ 115
Troubleshooting resources ...................................................................................................................... 115
System battery replacement........................................................................................................ 116
Regulatory information .............................................................................................................. 118
Safety and regulatory compliance ........................................................................................................... 118
Belarus Kazakhstan Russia marking ......................................................................................................... 118
Turkey RoHS material content declaration................................................................................................. 119
Ukraine RoHS material content declaration ............................................................................................... 119
Warranty information ............................................................................................................................ 119
Electrostatic discharge............................................................................................................... 120
Preventing electrostatic discharge ............................................................................................................ 120
Grounding methods to prevent electrostatic discharge................................................................................ 120
Specifications........................................................................................................................... 121
Environmental specifications ................................................................................................................... 121
Mechanical specifications ...................................................................................................................... 121

Contents 6
Power supply specifications .................................................................................................................... 122
Hot-plug power supply calculations.......................................................................................................... 122
Support and other resources ...................................................................................................... 123
Before you contact HP............................................................................................................................ 123
HP contact information........................................................................................................................... 123
Customer Self Repair ............................................................................................................................. 123
Acronyms and abbreviations...................................................................................................... 131
Documentation feedback ........................................................................................................... 136
Index....................................................................................................................................... 137

Component identification 7
Component identification
Front panel components
•Four-bay LFF drive model
Item Description
1 Optical drive (optional)
2 Serial label pull tab*
3 USB 2.0 connector
4 LFF drives (8.89 cm, 3.5 in)
*The serial number/iLO information pull tab is double-sided. The top side shows the server serial number and the
customer asset tag label. The reverse side shows the default iLO account information and QR code linking to product
documentation resources. The serial number/iLO information is printed on labels attached to the chassis.
•Eight-bay SFF drive model
Item Description
1 Front USB 3.0 connector (optional)
2 Serial label pull tab*
3 Optical drive (optional)
4 USB 2.0 connector
5 SFF drives (6.35 cm, 2.5 in)
*The serial number/iLO information pull tab is double-sided. The top side shows the server serial number and the
customer asset tag label. The reverse side shows the default iLO account information and QR code linking to product
documentation resources. The serial number/iLO information is printed on labels attached to the chassis.

Component identification 8
Front panel LEDs and buttons
•Four-bay LFF drive model
Item Description Status
1 UID button/LED* Solid blue = Activated
Flashing blue:
•
1 Hz/cycle per sec = Remote management or firmware upgrade
in progress
•
4 Hz/cycle per sec = iLO manual reboot sequence initiated
•
8 Hz/cycle per sec = iLO manual reboot sequence in progress
Off = Deactivated
2 Health LED* Solid green = Normal
Flashing green (1 Hz/cycle per sec) = iLO is rebooting.
Flashing amber = System degraded**
Flashing red (1 Hz/cycle per sec) = System critical**
3 NIC status LED* Solid green = Link to network
Flashing green (1 Hz/cycle per sec) = Network active
Off = No network activity
4 Power On/Standby button
and system power LED*
Solid green = System on
Flashing green (1 Hz/cycle per sec) = Performing power on sequence
Solid amber = System in standby
Off = No power present†
*When all four LEDs described in this table flash simultaneously, a power fault has occurred. For more information, see
"Power fault LEDs ("Front panel LED power fault codes" on page 10)."
**If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the system health
status.
†Facility power is not present, power cord is not attached, no power supplies are installed, power supply failure has
occurred, or the power button cable is disconnected.

Component identification 9
•Eight-bay SFF drive model
Item Description Status
1 UID button/LED* Solid blue = Activated
Flashing blue:
•
1 Hz/cycle per sec = Remote management or firmware upgrade
in progress
•
4 Hz/cycle per sec = iLO manual reboot sequence initiated
•
8 Hz/cycle per sec = iLO manual reboot sequence in progress
Off = Deactivated
2 Health LED* Solid green = Normal
Flashing green (1 Hz/cycle per sec) = iLO is rebooting.
Flashing amber = System degraded**
Flashing red (1 Hz/cycle per sec) = System critical**
3 NIC status LED* Solid green = Link to network
Flashing green (1 Hz/cycle per sec) = Network active
Off = No network activity
4 Power On/Standby button
and system power LED*
Solid green = System on
Flashing green (1 Hz/cycle per sec) = Performing power on sequence
Solid amber = System in standby
Off = No power present†
*When all four LEDs described in this table flash simultaneously, a power fault has occurred. For more information, see
"Power fault LEDs ("Front panel LED power fault codes" on page 10)."
**If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the system health
status.
†Facility power is not present, power cord is not attached, no power supplies are installed, power supply failure has
occurred, or the power button cable is disconnected.

Component identification 10
Front panel LED power fault codes
The following table provides a list of power fault codes, and the subsystems that are affected. Not all power
faults are used by all servers.
Subsystem Front panel LED behavior
System board 1 flash
Processor 2 flashes
Memory 3 flashes
Riser board PCIe slots 4 flashes
FlexibleLOM 5 flashes
Removable HP Flexible Smart Array
controller/Smart SAS HBA controller
6 flashes
System board PCIe slots 7 flashes
Power backplane or storage backplane 8 flashes
Power supply 9 flashes
For more information, see "Front panel LEDs and buttons (on page 8)."
Rear panel components
Item Description
1 Slot 1 PCIe3 x16 (16, 8, 4, 1)
2 Slot 2 PCIe3 x8 (8, 4, 1)
3 Slot 3 PCIe3 x16 (16, 8, 4, 1)
4 Non-hot-plug power supply
5
Power supply blank (bay 2 of optional redundant power
supply module)
6 Hot-plug power supply (bay 1 of optional redundant
power supply module)
7 NIC connector 2
8 NIC connector 1
9 Video connector
10 USB 3.0 connectors
11 Dedicated iLO module connector (optional)

Component identification 11
Rear panel LEDs
Item Description Status
1 UID LED Solid blue = Activated
Flashing blue:
•
1 Hz/cycle per sec = Remote management
or firmware upgrade in progress
•
4 Hz/cycle per sec = iLO manual reboot
sequence initiated
•
8 Hz/cycle per sec = iLO manual reboot
sequence in progress
Off = Deactivated
2 NIC link LED Green = Network link
Off = No network link
3 NIC activity LED Solid green = Link to network
Flashing green = Network active
Off = No network activity
4 Power supply LED Solid green = Normal
Off = One or more of the following conditions
exists:
•
Power is unavailable
•
Power supply failed
•
Power supply is in standby mode
•
Power supply error
PCIe riser board slot definitions
Expansion
Slots
Riser board
options
Technology Bus Width Connector
Width
Form Factor Notes
1
PCIe riser
FlexibleLOM
PCIe 3.0
FlexibleLOM
x16
x8
x16
x8
Full-height/H
alf-length
FlexibleLOM
Processor 1
2 PCIe riser PCIe 3.0 x8 x8 Low-profile Processor 1
3 PCIe riser PCIe 3.0 x16 x16 Low-profile Processor 2

Component identification 12
System board components
Item Description
1 Primary PCIe riser board connectors*
2 Dedicated iLO module connector
3 microSD slot
4 SATA 5 connector (for M.2 SSD 2)
5 SATA 4 connector (for M.2 SSD 1 or optical drive)
6 Internal USB 3.0 connector (for USB flash devices)
7 8SFF front USB 3.0 connector
8 Mini-SAS connector 1
9 Mini-SAS connector 2
10 Front I/O connector
11 DIMM slots for processor 1
12 Processor 1
13 Fan connector 7
14 Fan connector 6
15 Fan connector 5
16 Fan connector 4
17 Processor 2
18 Fan connector 3
19 Fan connector 2
20
DIMM slots for processor 2
21 Fan connector 1
22 Reserved
23 24-pin power supply connector
24 HP Smart Storage Battery connector
25
Power supply sideband signal connector
26 20-pin drive power connector
27 10-pin RPS connector

Component identification 13
Item Description
28 System battery
29 NMI header
30 TPM connector
31 Secondary PCIe riser board connectors*
32 System maintenance switch
33 FlexibleLOM sideband signal connector
* For more information on the riser board slots supported by the onboard PCI riser connectors, see "PCIe riser
board slot definitions (on page 11)."
DIMM slot locations
DIMM slots are numbered sequentially (1 through 8) for each processor. The supported AMP modes use the
letter assignments for population guidelines.
System maintenance switch
Position Default Function
S1 Off Off = iLO 4 security is enabled.
On = iLO 4 security is disabled.
S2 Off Off = System configuration can be
changed.
On = System configuration is locked.
S3 Off Reserved
S4 Off Reserved
S5 Off Off = Power-on password is enabled.
On = Power-on password is disabled.
S6 Off Off = No function
On = ROM reads system configuration
as invalid.

Component identification 14
Position Default Function
S7 Off Off = Set default boot mode to UEFI.
On = Set default boot mode to legacy.
S8 — Reserved
S9 — Reserved
S10 — Reserved
S11 — Reserved
S12 — Reserved
To access the redundant ROM, set S1, S5, and S6 to on.
When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all
system configuration settings from both CMOS and NVRAM.
CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. Be sure to
properly configure the server or data loss could occur.
IMPORTANT: Before using the S7 switch to change to Legacy BIOS Boot Mode, be sure the HP
Dynamic Smart Array B140i Controller is disabled. Do not use the B140i controller when the
server is in Legacy BIOS Boot Mode.
NMI functionality
An NMI crash dump creates a crash dump log before resetting a system which is not responding.
Crash dump log analysis is an essential part of diagnosing reliability problems, such as failures of operating
systems, device drivers, and applications. Many crashes freeze a system, and the only available action for
administrators is to restart the system. Resetting the system erases any information which could support
problem analysis, but the NMI feature preserves that information by performing a memory dump before a
system reset.
To force the system to invoke the NMI handler and generate a crash dump log, do one of the following:
•Use the iLO Virtual NMI feature.
•Short the NMI header ("System board components" on page 12).
For more information, see the HP website (http://www.hp.com/support/NMI).
Drive numbering
•Four-bay LFF drive model

Component identification 15
•Eight-bay SFF drive model
HP SmartDrive LED definitions
HP SmartDrives are the latest HP drive technology, and they are supported beginning with ProLiant Gen8
servers and server blades. The HP SmartDrive is not supported on earlier generation servers and server
blades. Identify an HP SmartDrive by its carrier, shown in the following illustration.
When a drive is configured as a part of an array and connected to a powered-up controller, the drive LEDs
indicate the condition of the drive.
Item LED Status Definition
1 Locate Solid blue The drive is being identified by a host application.
Flashing blue The drive carrier firmware is being updated or requires an update.
2 Activity ring Rotating green Drive activity
Off No drive activity
3 Do not remove Solid white Do not remove the drive. Removing the drive causes one or more of
the logical drives to fail.
Off Removing the drive does not cause a logical drive to fail.
4 Drive status Solid green The drive is a member of one or more logical drives.
Flashing green The drive is rebuilding or performing a RAID migration, strip size
migration, capacity expansion, or logical drive extension, or is
erasing.
Flashing
amber/green
The drive is a member of one or more logical drives and predicts
the drive will fail.
Flashing amber The drive is not configured and predicts the drive will fail.
Solid amber The drive has failed.
Off The drive is not configured by a RAID controller.
The blue Locate LED is behind the release lever and is visible when illuminated.

Component identification 16
IMPORTANT: The HP Dynamic Smart Array B140i Controller is only available in UEFI Boot Mode.
It cannot be enabled in Legacy BIOS Boot Mode. If the B140i controller is disabled, drives
connected to the system board Mini-SAS connectors operate in AHCI or Legacy mode. Under this
condition:
•The drives cannot be a part of a hardware RAID or a logical drive.
•The Locate, Drive status, and Do not remove LEDs of the affected drives are disabled.
Use BIOS/Platform Configuration (RBSU) in the UEFI System Utilities ("HP UEFI System Utilities" on
page 106) to enable or disable the B140i controller (System Configuration →BIOS/Platform
Configuration (RBSU) →System Options →SATA Controller Options →Embedded SATA
Configuration).
Fan locations

Operations 17
Operations
Power up the server
1. Connect each power cord to the server.
2. Connect each power cord to the power source.
3. Press the Power On/Standby button.
The server exits standby mode and applies full power to the system. The system power LED changes
from amber to green.
Power down the server
Before powering down the server for any upgrade or maintenance procedures, perform a backup of critical
server data and programs.
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC/DC power is removed.
IMPORTANT: When the server is in standby mode, auxiliary power is still being provided to the
system.
To power down the server, use one of the following methods:
•Press and release the Power On/Standby button.
This method initiates a controlled shutdown of applications and the OS before the server enters standby
mode.
•Press and hold the Power On/Standby button for more than 4 seconds to force the server to enter
standby mode.
This method forces the server to enter standby mode without properly exiting applications and the OS.
If an application stops responding, you can use this method to force a shutdown.
•Use a virtual power button selection through iLO 4.
This method initiates a controlled remote shutdown of applications and the OS before the server enters
standby mode.
Before proceeding, verify the server is in standby mode by observing that the system power LED is amber.
Extend the server from the rack
To extend the server from an HP, Compaq-branded, Telco, or third-party rack:
1. Power down the server (on page 17).
2. Remove all power:

Operations 18
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3. Disconnect all peripheral cables from the server.
WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is
adequately stabilized before extending a component from the rack.
WARNING: To reduce the risk of personal injury, be careful when pressing the server rail-release
latches and sliding the server into the rack. The sliding rails could pinch your fingers.
4. Do one of the following:
oIn a server that uses thumbscrew rack ears, loosen the captive thumbscrews that secure the server
faceplate to the front of the rack, and then slide the server out of the rack.
oIn a server that uses quick-release latch rack ears:
i. Open the latches on both sides of the server.
ii. If necessary, use a T-25 Torx screwdriver to loosen the shipping screws.

Operations 19
iii. Slide the server out of the rack.
5. After performing the installation or maintenance procedure, slide the server back into the rack, and then
press the server firmly into the rack to secure it in place.
6. Do one of the following:
oIn a server that uses thumbscrew rack ears, tighten the captive thumbscrews.
oIn a server that uses quick-release latch rack ears, if necessary, tighten the shipping screws.
7. Connect the peripheral cables.
8. Connect each power cord to the server.
9. Connect each power cord to the power source.

Operations 20
Access the product rear panel
Opening the cable management arm
To access the server rear panel:
1. Release the cable management arm.
2. Open the cable management arm. The cable management arm can be right-mounted or left-mounted.
Remove the server from the rack