HP ProLiant ML110 Assembly instructions

Generation 4 Server
Installation Sheet
Read instructions completely before beginning installation procedure.
Part number: 419978-001
First edition: September 2006
Configuring the server
1. Connect all peripherals:
•Keyboard
•Mouse
•Monitor
NOTE: Refer to the HP ProLiant ML110 Generation 4
Server Support CD contents for additional information and
updates not provided in this installation sheet.
2. Determine the server BIOS version:
a. Power up the server.
b. Press the Esc key at the HP logo screen, and then press the
Pause key to halt screen movement.
c. Note the server BIOS version.
d. Verify the server BIOS version against the latest BIOS
version listed for this server on the HP website:
http://www.hp.com
e. If you do not have the latest BIOS, update the BIOS now.
Refer to the HP ProLiant ML110 Generation 4 Server
Maintenance and Service Guide available on the HP
website: http://www.hp.com
Default boot priority
By default, the server searches for boot devices in the following
order:
1. CD-ROM/DVD-ROM
2. Removable Devices
3. Hard Drive
4. Embedded NIC
Identifying server components
Front panel components
1Optical drive 8Drive activity indicator
2Optical drive manual eject hole 9Front USB 2.0 ports
3Optical drive eject button 10 Hard drive EMI shield
4Optical drive activity indicator 11 Hard drive EMI shield screw
5Half-height common bay 12 Optical drive spare screws
6Power button 13 Hard drive spare screws
7Power LED indicator
Rear panel components
1PSU fan 9HP LO 100c Remote Management
Card port
2PS/2 mouse port 10 PCI slot covers
3PS/2 keyboard port 11 Kensington lock notch
4Serial port B 12 Power supply outlet
5Serial port A 13 Rear system fan
6VGA port 14 Thumbscrew for access panel
7Rear USB 2.0 ports 15 Cable lock provision tab
8LAN port (RJ-45) 16 PCI slot cover lock
System board components
Item Code Description
1 DIMM1 - 4 DDRII slots
2 P70 4-pin CPU fan connector
3 U3 Intel Mukilteo 2 (MCH)
4 XU1 Intel LGA775 CPU socket
5 P3 4-pin ATX CPU power connector
6 P8 4-pin system fan connector (rear)
7 J68 Top: PS/2 mouse port
Bottom: PS/2 keyboard port
Item Code Description
8 P53 Serial port A
Serial port B
9 J69 VGA port
10 J9 Top: LAN port
Bottom: USB 2.0 ports
11 U1033 Broadcom 5721 GbE chip
12 J32 PCI-Express x 8 line with x 8 slot
13 U11 ServerEngines Chip
14 J5 SMC FW
15 J20, J21 32-bit/33-MHz 3.3V PCI bus slot
16 J33 PCI-Express x 4 line with x 8 slot
17 XBT2 Battery
18 J10 HP LO 100c Remote Management Card slot
19 U38 Intel ICH7R
20 J2 System BIOS
21 P24 Front USB connector
22 P5 Front panel connector
23 P23 IDE channel UDMA-100
24 P60, P61,P62,P64 SATA 1-4 connector
25 J4 Internal USB connector for Tape
26 J3 Internal USB connector
27 P2 24-pin ATX system board power connector
Opening the server
The access panel and the front bezel are both detachable. You need
to remove these system covers before you can remove or replace a
server component.
Removing the access panel
HP Proliant ML110

HP Proliant ML110
Generation 4 Server
Installation Sheet
Read instructions completely before beginning installation procedure.
Part number: 419978-001
First edition: September 2006
Configuring the server
1. Connect all peripherals:
•Keyboard
•Mouse
•Monitor
NOTE: Refer to the HP ProLiant ML110 Generation 4
Server Support CD contents for additional information and
updates not provided in this installation sheet.
2. Determine the server BIOS version:
a. Power up the server.
b. Press the Esc key at the HP logo screen, and then press the
Pause key to halt screen movement.
c. Note the server BIOS version.
d. Verify the server BIOS version against the latest BIOS
version listed for this server on the HP website:
http://www.hp.com
e. If you do not have the latest BIOS, update the BIOS now.
Refer to the HP ProLiant ML110 Generation 4 Server
Maintenance and Service Guide available on the HP
website: http://www.hp.com
Default boot priority
By default, the server searches for boot devices in the following
order:
1. CD-ROM/DVD-ROM
2. Removable Devices
3. Hard Drive
4. Embedded NIC
Identifying server components
Front panel components
1Optical drive 8Drive activity indicator
2Optical drive manual eject hole 9Front USB 2.0 ports
3Optical drive eject button 10 Hard drive EMI shield
4Optical drive activity indicator 11 Hard drive EMI shield screw
5Half-height common bay 12 Optical drive spare screws
6Power button 13 Hard drive spare screws
7Power LED indicator
Rear panel components
1PSU fan 9HP LO 100c Remote Management
Card port
2PS/2 mouse port 10 PCI slot covers
3PS/2 keyboard port 11 Kensington lock notch
4Serial port B 12 Power supply outlet
5Serial port A 13 Rear system fan
6VGA port 14 Thumbscrew for access panel
7Rear USB 2.0 ports 15 Cable lock provision tab
8LAN port (RJ-45) 16 PCI slot cover lock
System board components
Item Code Description
1 DIMM1 - 4 DDRII slots
2 P70 4-pin CPU fan connector
3 U3 Intel Mukilteo 2 (MCH)
4 XU1 Intel LGA775 CPU socket
5 P3 4-pin ATX CPU power connector
6 P8 4-pin system fan connector (rear)
7 J68 Top: PS/2 mouse port
Bottom: PS/2 keyboard port
Item Code Description
8 P53 Serial port A
Serial port B
9 J69 VGA port
10 J9 Top: LAN port
Bottom: USB 2.0 ports
11 U1033 Broadcom 5721 GbE chip
12 J32 PCI-Express x 8 line with x 8 slot
13 U11 ServerEngines Chip
14 J5 SMC FW
15 J20, J21 32-bit/33-MHz 3.3V PCI bus slot
16 J33 PCI-Express x 4 line with x 8 slot
17 XBT2 Battery
18 J10 HP LO 100c Remote Management Card slot
19 U38 Intel ICH7R
20 J2 System BIOS
21 P24 Front USB connector
22 P5 Front panel connector
23 P23 IDE channel UDMA-100
24 P60, P61,P62,P64 SATA 1-4 connector
25 J4 Internal USB connector for Tape
26 J3 Internal USB connector
27 P2 24-pin ATX system board power connector
Opening the server
The access panel and the front bezel are both detachable. You need
to remove these system covers before you can remove or replace a
server component.
Removing the access panel

Removing the front bezel
Installing the PCI accessory board
The server supports four PCI bus slots.
•Two 32-bit/33-MHz 3.3V PCI bus slots (J20 to J21)
•One PCI-Express x4 line with x8 slot (J33)
•One PCI-Express x8 line with x8 slot (J32)
Installing mass storage devices
The four lower drive bays on the front panel can accommodate up to
four hard drives. The server supports both SATA and SAS drives.
WARNING! Power down the server before installing hard
drives.
CAUTION: Drives can be damaged by static electricity.
Before handling drives, touch an unpainted metal surface
to discharge static electricity.
Hard drive – shield removal
Hard drive – SATA/SAS
Installing optical drives
The two upper drive bays on the front panel can accommodate up to
two optical drives.
WARNING! Power down the server before installing
optical drives.
CAUTION: Drives can be damaged by static electricity.
Before handling drives, touch an unpainted metal surface
to discharge static electricity.
Optical drive – shield removal
Optical drive – installation
Installing memory
The server has four DIMM slots that support up to 8 GB maximum
system memory (2 GB in each of the four DIMM slots).
The following guidelines must be followed when memory modules
are being added or replaced:
•Use only DDR II 533/667 unbuffered ECC DIMMs in 512 MB,
1 GB or 2 GB module.
•Up to two DIMMs per channel, single-sided and/or double-
sided. Channel A corresponds to the DIMM1 and DIMM2
slots, while channel B corresponds to the DIMM3 and DIMM4
slots.
•For optimal 2 DIMMs configuration, populate slot 1 and slot 3.
Identical DIMMs are recommended.
CAUTION: DIMMs can be damaged by improper
handling. Always use an anti-static wrist strap and
grounding mat, and discharge static electricity before
touching DIMMs.
DIMM slots are structured to ensure proper installation. If you insert a
DIMM but it does not fit easily into the slot, you may have inserted it
incorrectly. Reverse the orientation of the DIMM and insert it again.
Replacing the processor
The LGA775 CPU socket in HP ProLiant ML110 Generation 4 server
supports Intel®Pentium®4, Intel®Pentium®-D, Celeron®-D processors
and Xeon®3000 series processors.
Getting additional documentation
For additional documentation, refer to HP ProLiant ML110
Generation 4 Server Support CD. You can also access additional
information and documentation from the HP website, www.hp.com
either by connecting directly or through the Support CD.
© Copyright 2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Intel, Pentium, Xeon and Celeron are trademarks or registered trademarks of
Intel Corporation or its subsidiaries in the United States and other countries.

Removing the front bezel
Installing the PCI accessory board
The server supports four PCI bus slots.
•Two 32-bit/33-MHz 3.3V PCI bus slots (J20 to J21)
•One PCI-Express x4 line with x8 slot (J33)
•One PCI-Express x8 line with x8 slot (J32)
Installing mass storage devices
The four lower drive bays on the front panel can accommodate up to
four hard drives. The server supports both SATA and SAS drives.
WARNING! Power down the server before installing hard
drives.
CAUTION: Drives can be damaged by static electricity.
Before handling drives, touch an unpainted metal surface
to discharge static electricity.
Hard drive – shield removal
Hard drive – SATA/SAS
Installing optical drives
The two upper drive bays on the front panel can accommodate up to
two optical drives.
WARNING! Power down the server before installing
optical drives.
CAUTION: Drives can be damaged by static electricity.
Before handling drives, touch an unpainted metal surface
to discharge static electricity.
Optical drive – shield removal
Optical drive – installation
Installing memory
The server has four DIMM slots that support up to 8 GB maximum
system memory (2 GB in each of the four DIMM slots).
The following guidelines must be followed when memory modules
are being added or replaced:
•Use only DDR II 533/667 unbuffered ECC DIMMs in 512 MB,
1 GB or 2 GB module.
•Up to two DIMMs per channel, single-sided and/or double-
sided. Channel A corresponds to the DIMM1 and DIMM2
slots, while channel B corresponds to the DIMM3 and DIMM4
slots.
•For optimal 2 DIMMs configuration, populate slot 1 and slot 3.
Identical DIMMs are recommended.
CAUTION: DIMMs can be damaged by improper
handling. Always use an anti-static wrist strap and
grounding mat, and discharge static electricity before
touching DIMMs.
DIMM slots are structured to ensure proper installation. If you insert a
DIMM but it does not fit easily into the slot, you may have inserted it
incorrectly. Reverse the orientation of the DIMM and insert it again.
Replacing the processor
The LGA775 CPU socket in HP ProLiant ML110 Generation 4 server
supports Intel®Pentium®4, Intel®Pentium®-D, Celeron®-D processors
and Xeon®3000 series processors.
Getting additional documentation
For additional documentation, refer to HP ProLiant ML110
Generation 4 Server Support CD. You can also access additional
information and documentation from the HP website, www.hp.com
either by connecting directly or through the Support CD.
© Copyright 2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Intel, Pentium, Xeon and Celeron are trademarks or registered trademarks of
Intel Corporation or its subsidiaries in the United States and other countries.