HP SA3150 Manual

hewlett-packard
vpn server appliance sa3150
regulatory information,
hardware installation,
and safety notices
Hewlett-Packard Company
HP: 5971-0871
P/N: A55305-001
March 2001

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information i
Disclaimer
Information in this document is provided in connection
with Hewlett-Packard Company products. No license,
express or implied, by estoppel or otherwise, to any
intellectual property rights is granted by this document.
Except as provided in Hewlett-Packard Company’s Terms
and Conditions of Sale for such products, Hewlett-Packard
Company assumes no liability whatsoever, and Hewlett-
Packard Company disclaims any express or implied
warranty, relating to sale and/or use of Hewlett-Packard
Company products including liability or warranties relating
to fitness for a particular purpose, merchantability, or
infringement of any patent, copyright or other intellectual
property right. Hewlett-Packard Company products are not
intended for use in medical, life saving, or life sustaining
applications.
Hewlett-Packard Company may make changes to
specifications and product descriptions at any time,
without notice.
This Hewlett-Packard VPN Server Appliance SA3150
Regulatory Information, Hardware Installation, and
Safety Notices document, as well as the software described
in it, is furnished under license and may only be used or
copied in accordance with the terms of the license. The
information in this manual is furnished for informational
use only, is subject to change without notice, and should
not be construed as a commitment by Hewlett-Packard
Company. Hewlett-Packard Company assumes no
responsibility or liability for any errors or inaccuracies that
may appear in this document or any software that may be
provided in association with this document.

ii Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
Except as permitted by such license, no part of this
document may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means without the
express written consent of Hewlett-Packard Company.
Copyright © Hewlett-Packard Company 2001.

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information iii
Contents
INTRODUCTION..........................................................................................................1
SPECIFICATIONS.................................................................................................................1
HARDWARE INSTALLATION..............................................................................................1
REGULATORY AND SAFETY..............................................................................................1
PHYSICAL SPECIFICATIONS....................................................................................2
ENVIRONMENTAL SPECIFICATIONS......................................................................3
ELECTRONIC AND ELECTRICAL SPECIFICATIONS.............................................4
VAC ELECTRICAL AND CONNECTOR SPECIFICATIONS...............................................4
LITHIUM BATTERY USAGE STATEMENT........................................................................4
COOLING REQUIREMENTS.......................................................................................5
HARDWARE INSTALLATION.....................................................................................6
MOUNTING OPTIONS..........................................................................................................6
CABLING REQUIREMENTS................................................................................................7
INSTALLING A PCI ADD-IN CARD.....................................................................................8
REGULATORY STATEMENTS FOR THE HP VPN SERVER APPLIANCE SA315011
FEDERAL COMMUNICATIONS COMMISSION WARNINGS AND SERVICE
REQUIREMENTS.......................................................................................................12
FCC WARNINGS.................................................................................................................12
SERVICE REQUIREMENTS...............................................................................................13
CANADIAN REGULATIONS .....................................................................................14
CANADIAN EQUIPMENT IDENTIFICATION REQUIREMENTS....................................14
EUROPEAN REGULATIONS.....................................................................................15
EUROPEAN COMMUNITY (CE) MARK OF CONFORMITY STATEMENT....................15
EUROPEAN POWER NOTICES.........................................................................................16
EUROPEAN REGULATORY INFORMATION...................................................................17
NOTICE TO UNITED KINGDOM USERS..........................................................................17

iv Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
JAPANESE REGULATIONS......................................................................................18
JAPANESE VOLUNTARY CONTROL COUNCIL FOR INTERFERENCE (VCCI)
STATEMENT.......................................................................................................................18
GERMAN REGULATIONS.........................................................................................19
WARNUNGEN.....................................................................................................................19
ELEKTROSTATISCHE ENTLADUNG...............................................................................19
UMGANG MIT KABELN.....................................................................................................20
INTERAKTION MIT ANDEREN GERÄTEN .....................................................................20
VENTILATION IM INSTALLATIONSUMFELD.................................................................20
SAFETY NOTICES.....................................................................................................21

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information 1
Introduction
This guide contains safety and regulatory information for
the HP VPN Server Appliance SA3150 as well as hardware
installation instructions. Read through this information
before installing the HP VPN Server Appliance SA3150.
Specifications
This guide contains the following specifications:
•Physical Specifications
•Environmental Specifications
•Electronic and Electrical Specifications
•Cooling Requirements
Hardware Installation
This guide contains the following hardware installation
topics:
•Mounting Options
•Installing a PCI Add-in Card
•Cabling Requirements
•Connecting the Cables
Regulatory and Safety
This guide contains the following regulatory and safety
information:
•Regulatory Statements
•Safety Notices

2Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
Physical Specifications
The following table contains the physical specifications for
the HP VPN Server Appliance SA3150.
Feature Measurement
U.S. or Imperial
Units Metric Units
Width 16.8 in. 42.67 cm
Length 20.5 in. 52.07 cm
Height 1.7 in. 4.32 cm
Weight
(maximum
configuration)
16 lbs. 7.26 kg

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information 3
Environmental Specifications
The following table contains the environmental
specifications for the HP VPN Server Appliance SA3150.
Feature Measurement
U.S. or Imperial
Units Metric Units
Altitude Up to 15,000 ft. Up to 4,572 m
External operating
temperature 5°to 104°F 10 °to 40°C
Relative humidity 20% to 80%,
noncondensing 20% to 80%, noncondensing
Storage
temperature 32°to 122°F 0°C to 50°C

4Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
Electronic and Electrical
Specifications
VAC Electrical and Connector Specifications
The following table contains the VAC electrical and
connector specifications for the HP VPN Server Appliance
SA3150.
Feature Specifications
Power
requirements 100 – 240 VAC
2.0 – 1.0 amps, 125 watts (max), 50/60 Hz
CAUTION: When installing multiple units
in a rack, do not overload the power circuit
to the rack.
Connectors 1 power cord connector
1 or 2 twisted-pair (10BaseT, 100BaseTX,
RJ-45) Ethernet connectors
The front panel has one RS232 DB-9 male
connector for a serial cable to a terminal
(console)
The rear panel has one asynchronous
(Comm) module RS232 DB-9 male
connector for a modem with rates up to
115.2 Kbps
Lithium Battery Usage Statement
There is danger of explosion if the battery is incorrectly
replaced. Replace only with the same or equivalent type of
battery, as recommended by the manufacturer. Discard
used batteries according to the manufacturer's
instructions.

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information 5
Cooling Requirements
To provide proper cooling, the HP VPN Server Appliance
SA3150 has air vents on the rear panels, and a cooling fan
located inside the front panel and the power supply. Plan
to leave a minimum clearance area of 2 inches (5
centimeters) around the side and rear panels. When you
route cables from the HP VPN Server Appliance SA3150, be
sure to avoid blocking the air vents and fan.

6Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
Hardware Installation
Mounting Options
The HP VPN Server Appliance SA3150 has the following
mounting options:
•Standalone device
•Stationary rack
Standalone Device
You can place the HP VPN Server Appliance SA3150 on a
secure surface as a standalone unit.
Stationary Rack
The HP VPN Server Appliance SA3150 ships with rack
mounting ears. Install the ears in the appropriate position
for your communications rack and mount the unit.
WARNING: The rack must be bolted to the floor, or anti-
tipping legs must be put in place before you install the rack
option.
The HP VPN Server Appliance SA3150 is 1U in height. If
the unit is mounted in an enclosed communications rack,
the recommended maximum rack ambient temperature
should be no greater than 40 degrees Celsius.
Installation of the equipment in the rack should be such
that the amount of airflow required for safe operation for
the equipment is not compromised.
Mounting of the equipment in the rack should be such that
a hazardous condition is not achieved due to uneven
mechanical load.

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information 7
Reliable earthing (grounding) of the unit should be
maintained. Particular attention should be given to supply
connection other than direct connections to the branch
circuit (such as power strips).
CAUTION: Ensure that a reliable earth ground is provided
for the rack.
Cabling Requirements
The HP VPN Server Appliance SA3150 is shipped with a
power cable and a DB-9 admin cable. The power cable is
6.5 feet (198 centimeters) in length, and the DB-9 Admin
cable is 65 inches in length (160 centimeters). Use the
following information to plan for the additional cables that
you need.
The HP VPN Server Appliance SA3150 also comes with two
ferrite bead cables that attach to your 10BaseT/100BaseTX
Ethernet connection.
Ethernet Cable Requirements
The HP VPN Server Appliance SA3150 supports twisted-
pair 10BaseT/100BaseTX Ethernet connections. Category
5 or better, 26 AWG cable must be used.
Safety Precautions
WARNING: Turn the power off, disconnect the power
cable, and disconnect all other cables before you perform
this procedure. Do not reattach any cables until you
replace the cover of the unit chassis and tighten the cover
screws on the chassis.
CAUTION: Attach the disposable grounding wrist strap to
your wrist and an exposed portion of the HP VPN device
chassis as indicated in the instructions on the wrist strap
packaging.

8Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
Installing a PCI Add-in Card
The vertically mounted riser card accommodates one
standard (left side) and one low-profile (right side) PCI
add-in card.
The following procedures describe how to install the add-
in card(s) in the server board:
•Removing the Cover
•Removing the Riser Card
•Removing the Rear I/O Filler Panel(s)
•Installing the Riser/Add-in Card(s)
•Closing the Cover
Note: Set the add-in card jumpers or switches according
to the manufacturer’s instructions.
Removing the Cover
1. Loosen and remove the release screw located on the
top panel of the HP VPN Server Appliance SA3150
chassis.
2. Slide the top cover back and lift to remove it.
Removing the Riser Card
Perform the following steps to remove the riser card from
the server board.
1. Grasp the riser card at each end and gently rock and
lift the riser card until it is loose from the server board
connector.
2. Remove the riser card from the server board
connector.

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information 9
Removing the Rear I/O Filler Panel(s)
Perform the following steps to remove the I/O filler
panel(s) from the rear panel of the server:
1. Use a Phillips screwdriver to remove the two screws
securing the filler panel retention bracket to the top
edge of the rear panel.
2. Remove the retention bracket.
3. Remove the filler panel from the expansion slot for the
type of add-in card(s) you are installing.
Installing the Riser/Add-in Card(s)
Perform the following steps to install the riser, with the
add-in card(s) attached, on the server board:
1. Align the riser card edge connector with the mating
riser connector on the server board. (The connectors
are keyed to mate in only one direction.)
Note: If you installed a low-profile card on the riser,
ensure that the right side of the low-profile card
bracket fits into the narrow slot on the right side of the
add-in card expansion slot.
2. Firmly press the riser/add-in card(s) straight down all
the way into the mating connector on the server board.
3. Use the Phillips screwdriver and the two screws
removed in the preceding procedure, “Removing the
Rear I/O Filler Panel(s),” to securely attach the filler
panel retention bracket to the top of the server rear
panel.
CAUTION: If you installed only one add-in card, ensure
that the empty expansion slot has a filler panel
installed before you attach the filler panel retention
bracket. An open expansion slot reduces the cooling
and EMI integrity of the server.

10 Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
Closing the Cover
Perform the following steps to close the cover after you
have installed the internal components.
1. Orient the cover with the recessed edge facing the front
panel of the server. The sides of the cover fit inside the
server chassis.
2. Slide the cover forward until the recessed edge is all
the way under the front edge of the server front panel.
3. Using a Phillips screwdriver, replace the screw
removed in the procedure, “Removing the Cover,” to
attach the server top cover securely.

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information 11
Regulatory Statements for the HP
VPN Server Appliance SA3150
The following sections describe safety and regulatory
information for the HP VPN Server Appliance SA3150.
Read through the regulatory information before installing
the HP VPN device in your network.
•FCC Warnings and Service Requirements
•Canadian Regulations
•European Regulations
•German Regulations
•Japanese VCCI Statement
•Safety Notices

12 Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
Federal Communications
Commission Warnings and Service
Requirements
FCC Warnings
The HP VPN Server Appliance SA3150 has been tested and
found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. The HP VPN device generates,
uses, and can radiate radio-frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio and
television communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.

Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information 13
Service Requirements
Do not attempt to repair or modify the HP VPN Server
Appliance SA3150. In the event of equipment malfunction,
all repairs to the HP VPN device should be performed by
Hewlett-Packard Company or a Hewlett-Packard
Company-authorized representative. It is the responsibility
of users requiring service to report the need for service to
Hewlett-Packard Company.

14 Hewlett-Packard VPN Server Appliance SA3150 Regulatory Information
Canadian Regulations
Canadian Equipment Identification
Requirements
This digital apparatus does not exceed the Class B limits
for radio noise emissions from digital apparatus set out in
the interference-causing equipment standard entitled:
Digital Apparatus, CES-003 of Industry Canada.
Cet appareil numérique respecte les limites de bruits
radioelectriques applicables aux appareils numérique de
Class B prescrites dans le norme sur le matérial broullier:
Apparell numérique, NMB-003 édictée par industrie
Canada.