HP Tc2110 - Server - 128 MB RAM User manual

HP Server tc2110
Network Operating System
Installation Guide
For:
Microsoft Windows NT 4.0 Server
Microsoft Windows 2000 Server and Microsoft Small Business Server 2000
Novell NetWare 5.1 and Novell Small Business Suite 5.1
Novell NetWare 6.0 and Novell Small Business Suite 6.0
Red Hat Linux 7.1TurboLinux Server 6.5
HP Part Number P5498-90018
Printed February 2002

Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and fitness
for a particular purpose. Hewlett-Packard shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this material. Hewlett-Packard assumes no
responsibility for the use or reliability of its software on equipment that is not
furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced, or
translated to another language without the prior written consent of Hewlett-
Packard Company.
Intel is a registered trademark of Intel Corporation. Microsoft and MS-DOS are
U.S. registered trademarks of Microsoft Corporation. Windows and Windows NT
are trademarks of Microsoft Corporation. Linux is a registered trademark of Linus
Torvalds. Novell and NetWare are registered trademarks of Novell, Incorporated.
Red Hat is a registered trademark of Red Hat Software, Incorporated. Adaptec is a
trademark of Adaptec, Incorporated. NVidia is a registered trademark of NVIDIA
Corporation in the United States and/or other countries. Turbolinux is a trademark
of Turbolinux, Inc. All other trademarks are the properties of their respective
holders.
Hewlett-Packard Company
Network Server Division
Technical Communications/MS 45SLE
10955 Tantau Avenue
Cupertino, California 95014 USA
© Copyright 2002, Hewlett-Packard Company.
ii

Contents
1HP Server tc2110 Installation Highlights for Experts ...................................1
Section 1. Introduction........................................................................................1
Section 2. Installation Highlights ........................................................................1
2Preparing your HP Server tc2110 for your NOS installation .......................3
Section 1. Hardware Setup ................................................................................3
Preparing your Hard Disk Drives ...................................................................3
Section 2. Updating your Server BIOS...............................................................3
Section 3. Run HP Diagtools..............................................................................4
Section 4. Using the Startup CD ........................................................................4
3Installing Microsoft Windows NT 4.0 Server .................................................5
Prepare the Installation ......................................................................................5
High Level Process Flow....................................................................................5
Section 1. Create the Drivers Diskettes .............................................................5
Section 2. Create Microsoft Windows NT Installation Diskettes ........................6
Section 3. Perform Windows NT Installation......................................................6
PHASE 1 – Drivers Installation ......................................................................7
PHASE 2 – Hard Drive Preparation ...............................................................7
PHASE 3 - System Configuration Details ......................................................8
PHASE 4 – Configure the Network ................................................................9
PHASE 5 – Completing the Installation .......................................................10
PHASE 6 – Install the Service Pack ............................................................11
PHASE 7 – Install HP Video Driver..............................................................12
Section 4. Initialize Hard disk Drive..................................................................12
Section 5. Perform Hardware Status Check ....................................................13
Section 6. Attach Clients to Network and Test Network Link...........................13
Section 7. Installing Additional Adapters Drivers .............................................14
Ethernet Adapter ..........................................................................................14
HP NetRAID-1M Adapter .............................................................................14
Troubleshooting................................................................................................14
Tip #1. Troubleshooting SCSI Host Bus Adapter Configuration..................15
Tip #2. NT Warning About Drives with More than 1024 Cylinders ..............15
Tip #3. Service Pack Files Replaced Without Feedback.............................16
Tip #4. Using the NT Event Log to Diagnose Network Adapter Problems ..16
iii

Contents
Tip #5. Booting from Another SCSI HDD.....................................................17
Tip #6. Restarting Windows NT installation .................................................17
On-Line Information and Software Sources.....................................................17
4Installing Microsoft Windows 2000 Server and Small Business Server
2000 .....................................................................................................................19
Prepare the Installation ....................................................................................19
High level process flow ....................................................................................19
Section 1. Create the Drivers Diskettes ...........................................................19
Section 2. Perform Windows 20000 Installation ..............................................20
Section 3. Completing the Installation..............................................................22
PHASE 1 – Install the Service Pack ............................................................22
PHASE 2 – Install the Chipset Driver ..........................................................23
PHASE 3 – Install the HP Video Driver .......................................................23
PHASE 4 – Install the HP LAN driver ..........................................................24
PHASE 5 – Install Windows 2000 Recovery Console .................................24
Section 4. Configure the system ......................................................................24
PHASE 1 – Perform Hardware Status Check..............................................24
PHASE 2 - Initialize Hard Disk Drive ...........................................................25
PHASE 3- Adding Terminal Server Services...............................................26
Section 5. Configure the network .....................................................................28
PHASE 1 -- Configure Server IP Address ...................................................28
PHASE 2 -- Attach Clients to Network and Test Network Link....................28
PHASE 3 -- Domain Controller Setup..........................................................29
Troubleshooting ...............................................................................................30
Tip #1. Upgrading from NT 4.0 to Windows 2000 .......................................31
Tip #2. Windows 2000 Installation halts about three minutes after starting to
boot from CD-ROM ......................................................................................31
Tip #3. Configure the Parallel (LPT) Port for ECP Mode.............................32
Tip #4. Installing HP NetRAID-1M Driver After Windows 2000 is Installed 32
Tip #5. Windows 2000 Drivers Signatures...................................................32
Tip #6. Windows 2000 Recovery Options....................................................33
Tip #7. Restarting Windows 2000 installation..............................................35
On-Line Information and Software Sources.....................................................35
5Installing Novell NetWare 5.1 and Novell Small Business Suite 5.1 .........37
Prepare the Installation ....................................................................................37
High level process flow ....................................................................................37
Section 1. Run HP Diagtools (optional) ...........................................................37
iv

Contents
Section 2. Create the Drivers Diskettes ...........................................................37
Section 3. Perform NetWare 5.1 or Novell Small Business Suite 5.1 Installation38
PHASE 1 – Start the Installation ..................................................................38
PHASE 2 – Install HP Drivers ......................................................................40
PHASE 3 – Configure the Network ..............................................................41
Section 4 Install the Support Pack ...................................................................42
Troubleshooting................................................................................................43
Tip #1. Restarting NetWare Installation .......................................................44
On-Line Information and Software Sources .....................................................44
6Installing Novell NetWare 6.0 and Novell Small Business Suite 6.0 .........45
Prepare the Installation ....................................................................................45
High level process flow.....................................................................................45
Section 1. Run HP Diagtools (optional)............................................................45
Section 2. Create the Drivers Diskettes ...........................................................45
Section 3. Perform NetWare 6.0 or SBS 6.0 Installation .................................46
PHASE 1 – Start the Installation ..................................................................46
PHASE 2 – Install HP Drivers ......................................................................48
PHASE 3 – Configure the Network ..............................................................49
Troubleshooting................................................................................................50
Tip #1. Restarting NetWare Installation .......................................................51
On-Line Information and Software Sources .....................................................51
7Installing Red Hat Linux 7.1 ..........................................................................53
Prepare the Installation ....................................................................................53
High level process flow.....................................................................................53
Perform Red Hat Linux Installation ..................................................................53
PHASE 1 – Launch the Installation..............................................................53
PHASE 2 – Configure the Server.................................................................53
PHASE 3 – Complete the Installation ..........................................................54
On-Line Information and Software Sources .....................................................55
8Installing TurboLinux Server 6.5 ..................................................................57
Prepare the Installation ....................................................................................57
High level process flow.....................................................................................57
Perform TurboLinux Installation .......................................................................57
PHASE 1 – Launch the Installation..............................................................57
PHASE 2 – Configure the Server.................................................................57
PHASE 3 – Complete the Installation ..........................................................58
v

Contents
On-Line Information and Software Sources.....................................................58
vi

1 HP Server tc2110 Installation
Highlights for Experts
Section 1. Introduction
This chapter is for expert users only, and assumes they are familiar with the
standard installation process of their NOS.
HP recommends taking into account the following specific information in order to
adapt your usual NOS installation to the particularities of your HP server tc2110.
The detailed instructions relative to each specific step (location of drivers,
workarounds) are provided in the respective NOS chapters.
Section 2. Installation Highlights
*Based on your tc2110 configuration
HP drivers
Video driver
Intel LAN driver
SCSI driver *
Microsoft
Windows NT 4.0
Server
Highlights none
HP drivers
Intel chipset driver
Video driver
Intel LAN driver
SCSI driver *
Microsoft
Windows 2000
Server and Small
Business Server
2000 Highlights none
Novell NetWare
5.1 and Novell
Small Business
Si 51
HP drivers Intel LAN driver
SCSI driver *
1

Chapter 1 HP Server tc2110 Installation Highlights for Experts
Suite 5.1
Highlights
Create NetWare patch file diskette (refer to
Chapter 5 | Section 2)
For Novell SBS, use floppy disk to initialize
the NOS installation (refer to Chapter 5 |
Section 3 | Phase 1)
Install NetWare patch file (refer to Chapter 5
| Section 3 | Phase 1)
Install NW 5.1 Support Pack 3 or above
(refer to Chapter 5 | Section 4)
HP drivers SCSI driver *
Novell NetWare
6.0 and Novell
Small Business
Suite 6.0 Highlights
For Novell SBS, use floppy disk to initialize
the NOS installation (refer to Chapter 6 |
Section 3 | Phase 1)
HP drivers none
Red Hat Linux
7.1 Highlights none
HP drivers none
TurboLinux
Server 6.5 Highlights none
The HP drivers specific to your server are available on the HP Startup CD-ROM.
2

2 Preparing your HP Server tc2110 for
your NOS installation
Section 1. Hardware Setup
Prepare your HP server following the instructions in the HP Server tc2110
Operations and Maintenance Guide.
It is recommended that you do not install any third party adapter until you verify
that the HP equipment is functioning properly and you complete the NOS
installation.
Preparing your Hard Disk Drives
The HP Tower Server tc2110 comes with new hard disk drive(s) that do not need
specific setup. If you install additional and USED hard disk drives in your new
server:
· Note that most NOS installations remove all data from the hard disk they are
installed on. If you wish to use your additional hard disk drives to access
existing data in you new server, HP recommends that you install and
configure this (these) hard disk drive(s) AFTER completing the NOS
installation.
· If you wish to recycle used hard disk drives:
a. Perform a media check
b. Use a utility such as fdisk to erase all data and partitions from your hard
drive.
Section 2. Updating your Server BIOS
HP recommends that you update your server BIOS with the latest system BIOS
version to enjoy the most recent compatibility fixes.
Insert the HP Startup CD in a Windows PC and follow the on-screen instructions.
NOTE If the Windows PC does not auto-start the Startup menu, start it
by opening Startup.htm, found at the root level of the Startup
CD.
3

Chapter 2Preparing your HP Server tc2110 for your NOS installation
Section 3. Run HP Diagtools
To perform HP Diagtools hardware diagnostic on your HP Server tc2110, switch
off your HP server then reboot on the Startup CD and follow the on-screen
instructions. View and save the hardware inventory after the test.
Section 4. Using the Startup CD
The Startup CD included with your HP Server tc2110 system may be used as
follows:
Startup CD Usage
Method 1 Method 2 Method 3
Insert CD in your new
HP server and reboot it.
This will run HP
Diagtools (a DOS
program)
Insert the CD in a PC
that includes a HTML
browser.
Open the file
startup.htm.
This allows you create
drivers diskettes (HTML
menus)
Insert the CD in the server
once the NOS is
running.*
Open the file startup.htm.
This allows you create
drivers diskettes and
provides an automated
installation of Windows
NT or 2000 video drivers
(HTML menus).
* This method is not available on NetWare servers since they don't have an HTML browser.
4

3 Installing Microsoft Windows NT 4.0
Server
Prepare the Installation
Please refer to the Chapter 1 "Preparing your HP Server tc2110 for your NOS
installation" for our recommendations on the server preparation.
Then gather the following material:
· HP Server tc2110 Startup CD
· Microsoft Windows NT4 CD-ROM as well as the latest Microsoft NT
Service Pack (#6a or above)
· Seven blank formatted 3.5-inch diskettes
· Two or more clients for testing purpose (Optional)
To avoid problems use only hardware that appears on the Windows NT Hardware
Compatibility List. (HCL) You can access the latest HCL via Microsoft's Web site
at http://www.microsoft.com/ntworkstation/
High Level Process Flow
1. Create the drivers diskettes using HP Startup CD.
2. Create Microsoft Windows NT installation diskettes.
3. Perform Windows NT installation.
4. Initialize Hard Disk Drives.
5. Perform Hardware status check with "Windows NT Diagnostic Tool".
6. Attach clients to network and test network link.
7. Install additional HP accessories.
Section 1. Create the Drivers Diskettes
1. Locate three blank, formatted 3.5" diskettes.
2. Insert your HP Startup CD in a Windows PC and follow the on-screen
instructions to create the following diskettes:
5

Chapter 3Installing Microsoft Windows NT 4.0 Server
o HP Server tc2110 Windows NT SCSI driver (HP disk NT SCSI)
o HP Server tc2110 Windows NT LAN driver (HP disk NT LAN #1 and #2)
NOTE If the Windows PC does not auto-start the Startup menu, start it
by opening Startup.htm found at the root level of the Startup
CD.
Section 2. Create Microsoft Windows NT
Installation Diskettes
Three installation diskettes are required to install Microsoft Windows NT 4.0 on
your server. Follow these steps to create these installation diskettes:
1. Locate three blank, formatted 3.5" diskettes.
2. Insert your Microsoft Windows NT 4.0 CD-ROM into a desktop PC.
3. From a DOS prompt, type:
C:\D:\i386\winnt32 /ox
(where Dis the drive letter for the CD-ROM)
4. Follow the prompt and insert the diskettes in the order described.
Section 3. Perform Windows NT Installation
The installation of Windows NT contains several phases:
· Phase 1 – Driver(s) Installation
· Phase 2 – Hard Drive Preparation
· Phase 3 – System Configuration Details
· Phase 4 – Configuring the Network
· Phase 5 – Completing the Installation
· Phase 6 – Install the Service Pack
· Phase 7 – Install the HP Video Driver
6

Chapter 3Installing Microsoft Windows NT 4.0 Server
NOTE Do not try to install Windows NT 4.0 via booting from the
Windows NT CD-ROM. This method of installation does not
work properly on most servers. The installation procedure will
prompt you to insert the Windows NT CD-ROM at a later
time.
PHASE 1 – Drivers Installation
1. Insert the Windows NT Setup/Boot Diskette #1 and boot the system.
2. Replace the diskette when prompted and press Enter.
3. Once under Windows NT Server Setup menu, press Enter to continue.
4. Press Enter to launch the automatic detection of mass storage device. It will
detect the IDE CD-ROM and propose the appropriate driver.
5. If you have a SCSI model:
a. Press S to to specify additional SCSI adapters. The Windows NT installer
will display a scrolling list of options.
b. Press Enter to select the default option "Other (Requires Disk provided
by a hardware manufacturer)".
c. When prompted to insert the "Manufacturer-supplied hardware support
disk", insert the HP Server tc2110 Windows NT SCSI driver (HP disk NT
SCSI) into floppy drive then press Enter.
d. Press Enter to select the "Adaptec Ultra160 Family PCI SCSI controller".
6. ""Ensure that both the PCI SCSI (if applicable) and CD-ROM IDE
controllers are properly detected by checking the status at the top of the
screen. The installation will not be successful if these two drivers are not
properly installed.
7. If you have any more mass storage device drivers to install, you may do so at
this time by pressing S.
8. When completed, press Enter to continue.
PHASE 2 – Hard Drive Preparation
1. Press Enter to continue if you are warned about your hard disk containing
more than 1024 cylinders. Your HP system can indeed handle this correctly.
2. Press C when prompted, to continue with the installation.
7

Chapter 3Installing Microsoft Windows NT 4.0 Server
NOTE Windows NT setup will prompt a different menu if you have
reconfigured your new HP server to use a hard drive already
containing data.
3. Insert the Windows NT CD-ROM when prompted then press Enter.
NOTE Your CD-ROM drive needs few seconds to detect the newly
inserted CD-ROM. You may need to press Enter again if you
pressed Enter too quickly the first time.
4. Press Page Down to read the Licensing Agreement then F8 to agree and
proceed with the installation.
5. The Windows NT Server Setup screen will display the system hardware and
software components it detected. Press Enter if the configuration matches
your computer.
6. The setup then shows a list of hard drives on your server, along with the
partitions proposed on each drive. The default partition on which to install
Windows NT on the first drive (Drive 0) is highlighted. Select Cto create a
partition in the unpartitioned space.
7. Enter the appropriate size for your NOS partition. HP recommends 2000MB.
Press Enter to validate the partition size.
8. Press Enter to Install Windows NT on the "New (Unformatted)" partition.
9. Select a file system format: FAT (DOS type file system) or NTFS (Windows
type file system) for this NOS partition. HP recommends using NTFS. Then
press Enter to proceed with formatting the partition (this operation may take
time, depending on your partition size).
10. Specify the directory for Windows NT (default = \WINNT)then press Enter
11. Press Enter to have Setup examine your hard disks.
12. Insert the HP Server tc2110 Windows NT SCSI driver (HP disk NT SCSI)
when prompted for a disk, then press Enter
13. Remove the above disk and Windows NT CD-ROM from their drives before
pressing Enter to restart your computer.
PHASE 3 - System Configuration Details
1. Insert Windows NT Server CD-ROM when prompted then press Enter.
8

Chapter 3Installing Microsoft Windows NT 4.0 Server
NOTE Your CD-ROM drive needs few seconds to detect the newly
inserted CD-ROM. If the window "Files Needed" appears,
press Enter again.
2. Click Next at the Windows NT Server Setup screen to gather information
about your computer.
3. You can now proceed through the customization of your installation using
the graphical interface.
NOTE You can later promote your "Backup domain controller" to
"Primary domain controller" and vice versa. "Stand Alone
Server" cannot be promoted to "Primary Domain Controller" or
demoted to "Backup Domain Controller".
4. Emergency repair disk: HP recommends you create this disk because it saves
your Windows NT Server Setup configuration. Prepare a blank formatted
floppy diskette to create this disk then click Next. You do not need to insert
the blank floppy diskette at this time as Windows NT Setup will actually
perform the disk creation at the end of you configuration phase.
PHASE 4 – Configure the Network
1. Click Next at the Windows NT Setup screen to install Windows NT
Networking.
2. Click Next at the following window to use the network adapter embedded
with your HP Server tc2110.
3. Click Next to accept installing the Microsoft Internet Information Server.
4. When you reach the Network Adapters screen, do NOT select Start Search.
Instead, click the Select from list… button to load the HP LAN driver:
a. Select the Have Disk button when given a list of Network Adapter
drivers, to use HP specific driver
b. Insert the HP Server tc2110 Windows NT LAN driver (HP disk NT LAN
#1) then press Enter
c. Press Enter to validate the selection of the "Intel® PRO Adapter", then
Enter again to confirm the Network Adapters selection.
d. When prompted, insert the second driver disk (HP disk NT LAN #2).
5. Follow the on-screen instructions to complete the selection of the Network
Protocols and Network Services.
9

Chapter 3Installing Microsoft Windows NT 4.0 Server
NOTE The network settings need to be customized to your
environment. Please refer to Microsoft NT Server manuals
should you need further details on the networking settings.
6. Click Next to install all above selected components when prompted by
Windows NT Server Setup.
NOTE If you choose to specify an IP address and skip the installation
of the DHCP component, Windows NT Server installation will
open Microsoft TCP/IP Properties window where you should
enter your IP address. You may configure this IP address again
after completion of the Windows NT install by selecting Start |
Settings | Control Panel | Network | Protocols | TCP/IP Protocol
Properties.
7. Click Next at the Network Bindings window to keep the default services.
8. Click Next to start the Network.
9. Click Next to confirm the Domain your server will operate in.
PHASE 5 – Completing the Installation
1. Choose Finish to perform the last installation step.
2. Windows NT Server 4.0 will then proceed with the installation of Microsoft
Internet Information Server 2.0:
a. Press Enter to keep default setup options then Enter again to confirm
creating the corresponding installation directory.
b. Press Enter to keep default publishing directories then Enter again to
confirm their creation.
c. Read the information related to setting-up a Internet Domain then press
OK.
d. Select appropriate ODBC drivers (select at least the default SQL Server
Drivers) then press OK
3. Set the Time zone, Date, and Time then select Close.
4. You will be notified that a standard VGA video driver has been installed. Do
not attempt to install the HP high-resolution video driver at this time because
they would be overwritten by the service pack installation. We will help you
perform this operation later. Click OK to leave this window, then OK again
to close the "Display Properties" window.
10

Chapter 3Installing Microsoft Windows NT 4.0 Server
5. When prompted, insert the blank formatted disk to create the Emergency
Repair Disk then click OK.
6. When prompted, remove the Emergency Repair disk and the Windows NT
Server CD-ROM from their drives and reboot the system by pressing Enter.
7. The Windows NT logon screen will show after the POST, as the basic
Windows NT installation is now complete.
NOTE Windows NT installation may take a while at this step if you
selected NTFS and the system has to convert the boot partition
from FAT to NTFS.
PHASE 6 – Install the Service Pack
1. How to get a copy of Windows NT 4.0 Service Packs:
o If your HP server is already connected to internet, you can download the
latest Service Pack from Microsoft website at
http://www.microsoft.com/ntserver/nts/downloads/recommended
o If you have access to a PC connected to internet and equipped with a
CD-RW drive, you may download the latest Service Pack from Microsoft
website at
http://www.microsoft.com/ntserver/nts/downloads/recommended then
copy the Service Pack on a CD-ROM. It allows you to install the Service
Pack from the CD-ROM drive of your HP server.
o You may contact Microsoft Support at [phone] or [phone]
to have a Service Pack CD-ROM shipped to you.
2. To install the Service Pack, login on your HP server as the Administrator,
then run the Service Pack.
3. Select "Accept the License Agreement" then click Install.
4. When prompted, click Restart to reboot your system (remember to remove all
diskettes and CD-ROM from their respective drives).
NOTE When installing the service pack, answer No if prompted to
overwrite drivers files, to keep the HP drivers you have
previously installed.
11

Chapter 3Installing Microsoft Windows NT 4.0 Server
PHASE 7 – Install HP Video Driver
The Microsoft Windows installation process has installed the standard VGA video
driver. If you would like to make use of the high-resolution video driver, follow
these steps:
1. Ensure Microsoft Windows NT Service Pack (version #6a or above) is
installed. This is a REQUIREMENT.
2. Logon as the Administrator on your HP server then insert HP Startup CD in
the CD-ROM drive. The Startup CD will automatically start and a menu will
display.
NOTE Your HP server should auto-detect the presence of the Startup
CD and start the Startup menu. If your HP server does not
auto-start the Startup menu, start it by opening Startup.htm
which can be found at the root level of the Startup CD.
3. Select ""the NT 4.0 video driver in the "Drivers summary table / accessing hp
drivers" page.
4. The HP video driver setup program will open. Click Next to start the
installation.
5. Select “NVIDIA Vanta”.
6. Click Finish when prompted to restart your system at the end of the
installation.
7. After your logon, you will be notified that default display resolutions are
being used. Click OK. You can now configure your settings and test them.
Section 4. Initialize Hard disk Drive
To manage your different drives and partitions:
1. Click Start | Programs | Administrative Tools | Disk Administrator.
2. Click OK to proceed when notified you have a new hard disk to configure.
3. Select available hard disk space on the graphic and use menus to create
additional partitions.
4. Exit the Disk Administrator.
5. To complete formatting of new partitions, open My Computer, right click on
a new partition(s) to be formatted and select format.
12

Chapter 3Installing Microsoft Windows NT 4.0 Server
Section 5. Perform Hardware Status Check
This section will provide a simple way to verify your installation of Windows NT.
Note that Windows NT Resource Guide CD-ROM (available from Microsoft)
provide utilities to generate activities to stress the system. The following steps use
standard tools provided with the Windows NT Server installation.
1. Inspect the error log in the event viewer (Start | Programs | Administrative
Tools | Event Viewer) to verify that no errors were detected. If any errors are
found please refer to the troubleshooting section of this document and
Windows NT Reference Manual for help.
NOTE Windows NT Event Viewer may have recorded network errors
if your HP server was not connected prior to your login.
If you can not resolve the problem please contact your HP
service representative or use HP website for additional
troubleshooting resources.
2. Run the "Windows NT Diagnostic Tool" (Start | Programs | Administrative
Tools | Windows NT Diagnostic) to gather information about system BIOS,
resources, physical memory and video.
3. Check that your different adapters are correctly installed:
a. Open the control panel (Start | Settings | Control Panel)
b. Check the status of the Network adapter. You may perform the
diagnostics by selecting the Diagnostics tab then click on Run Tests.
Upon completion, close the window (if you performed the diagnostics,
Windows will recommend that you reboot the system).
c. Check the status of your SCSI adapter by selecting SCSI Adapters in the
Control Panel and click Properties for each device.
Section 6. Attach Clients to Network and Test
Network Link
1. Create shares: create a folder on your hard drive then share it (right click on
folder and the select Sharing).
2. Create users using Windows NT utility: Start | Programs | Administrative
Tools | User Manager - DOMAIN
3. Connect clients PC to the network your HP server operates on.
13

Chapter 3Installing Microsoft Windows NT 4.0 Server
4. Open a command prompt window on your HP server (Start | Program |
Command Prompt) and verify the TCP/IP configuration you have set during
Windows NT installation by entering:
ipconfig /all
5. To verify the server and clients can communicate properly:
a. From one of the clients, open a command prompt and type:
ping computername
Where computername is the server name you entered during Windows
NT installation. You should get four reply's from your new server. If
there is a link problem it must be fixed before going any further.
You may test the link further by doing a ping between two clients at the
same command prompt, type:
ping other_client_IPaddress
You should get four replies from the second client.
b. Copy files back and forth from the clients to the server.
Section 7. Install Additional HP Accessories
The hp server tc2110 Startup CD includes the drivers for the following HP
accessories:
· HP-Intel 10/100 LAN
· HP NetRAID-1M adapter
· HP Surestore DAT24i
Please refer to the product manual enclosed with your accessory for the detailed
installation procedures.
Troubleshooting
This section will help you resolve some of the most common installation
problems.
14