HP ProLiant DL100 G2 DPSS User manual

Page 1
*372017-004*
About this document
This document provides procedures for rack installation of an HP
ProLiant DL100 G2 1TB, 3TB, or 6TB Data Protection Storage
Server (DP Storage Server). Instructions for installing optional HP
StorageWorks Modular Smart Array (MSA) storage systems are
included with the MSA storage system. HP assumes that you are
qualified in servicing computer equipment, and trained in
recognizing hazards in products with hazardous energy levels.
Safety information
Before installing this product, read the Important Safety
Information document provided.
Regulatory notice
The rating label on the device gives the class (A or B) of the
equipment. Class B devices have an FCC logo or ID on the label.
Class A devices do not have an FCC logo or ID on the label. After
you have determined the device class, see the HP ProLiant Data
Protection Storage Server user guide for complete regulatory
compliance notices. This guide is printed, and also provided in the
product kit as a file on the documentation CD.
Kit contents
1HP ProLiant DL100 G2 1TB,
3TB, or 6TB DP Storage
Server (Microsoft®System
Center Data Protection
Manager (DPM) software and
OS preloaded)1
1. HP StorageWorks MSA20 and cables are shipped separately.
2HP ProLiant Data Protection
Storage Server
Documentation CD (includes
HP ProLiant Data Protection
Storage Server user guide, HP
ProLiant Data Protection
Storage Server expansion
guide, and Microsoft DPM
Planning and Deployment
guide)
3Quick Restore DVD 4HP Storage Server Service
Release 5.5 DVD; use only
Multi-lingual User Interface
(MUI) updates
5Bezel 6Power cord
7Slide rail assembly2
2. Slide rail assemblies vary. The click-and-snap assemblies hook onto the
rack. The hardware-mounted assemblies attach to the rack using supplied
screws, star washers, and locator washers.
8Thumbscrew brackets and
screws
6
5
1
7
2
3
4
8
5200a
HP ProLiant DL100 G2 1TB,
3TB, and 6TB Data Protection
Storage Server
installation instructions
© Copyright 2005 Hewlett-Packard Development Company, L.P.
First edition September 2005
Product names mentioned herein may be trademarks of their
respective companies as reflected by an associated footnote. The
information in this document is subject to change without notice.
Printed in the US.
www.hp.com

Page 2
Front panel
Back panel
Installing the server into the rack
NOTE: Depending on the rail assembly provided, your slide
rails may vary slightly from those in the following illustrations.
CAUTION: Always install the heaviest item first, and continue
to populate the rack from bottom to top.
1. Install the slide rails:
a. Attach the slide rails, as shown:
• For hardware-mounted assemblies (A), mount the slide
rails onto the rack using the supplied screws and star
washers. For square-hole racks, use the provided locator
washers.
• For click-and-snap assemblies (B), hook the slide rails onto
the rack. At both ends of the slide rail, push the outer
spring latch 1, and then slide the spring mechanism
toward the rail end until the rail is secure 2.
IMPORTANT: For hardware-mounted rails, HP
recommends leaving the screws loose until the server is completely
installed. This eases installation by preventing binding of the server
in the rack.
1Slim DVD-ROM
2Individual HDD status LED
32 USB ports
4Overall HDD activity LED
5Overall HDD fault LED
6NIC LEDs
7UID LED
8Power LED
9UID button
10 Power button
11 HDD bays (0-3)
1Dual USB port
2PS/2 mouse port
3NIC connectors (RJ45) (1-2)
4UID LED
5Low profile, half length PCI-X
slot
6Full height, full length PCI-X slot
7AC power connector
8PS/2 keyboard port
9Serial port
10 D-sub VGA port
10699
3 4 8 10
6
5 7 9
1 2
11
10700
8 9
531 42 6 7
10
5201 A
1
2
A
B

Page 3
b. Locate the inner slide rails:
• On hardware-mounted assemblies, remove the inner slide
rails from the outer slide rails. To do so, extend the inner
slide rails from the front of the rack until they lock in place.
Then, press the inner slide lock down, as shown, and pull
the inner slide rails straight out.
• On click-and-snap assemblies, the inner slide rails arrive
separate from the outer slide rails.
2. Prepare the server:
a. Attach the two thumbscrew brackets to the server using the
supplied bracket screws, as shown 1.
b. Attach a slide rail (lock facing out) to each side of the server,
insert the slide rail screws through the slide rails, and then
tighten, as shown 2.
c. Attach the bezel 3to the thumbscrew brackets, and then lock
(if desired).
3. Install the server:
a. With the outer slide rails extended a short distance from the
rack, insert the inner slide rails (with the server attached) into
the outer slide rails, as shown 1. Press the inner slide lock 2,
and then push the server all the way into the rack, making
sure that the inner slide rails lock into place.
b. Slide the server in and out of the rack several times, allowing
the slide rails to position properly 1.
c. Lock the server in place using the thumbscrews 2.
10685
5202
1
1
2
32
5203A
2
1
5204
2
1

Page 4
d. If installing a hardware-mounted assembly, tighten all the
slide rail screws.
4. Install the MSA cable:
• For the 3TB model, install the MSA cable, as shown.
• For the 6TB model, install the cable for the second MSA in the
adjacent slot.
5. Connect the power cord to the back of the server.
Starting the DP Storage Server
To begin the first-time startup procedure:
•Ensure that the server is safely installed in an adequate
environment.
•Ensure that the power cables and peripheral devices are
plugged in, and that AC power is supplied to the server.
•See the DP Storage Server startup chapter in the HP ProLiant
Data Protection Manager Server user guide.
5205