HP 6125XLG Installation manual
HP 6125XLG Blade Switch
Fundamentals
Command Reference
Part number: 5998-5359a
Software version: Release 240x
Document version: 6W101-20150515
Legal and notice information
© Copyright 2015 Hewlett-Packard Development Company, L.P.
No part of this documentation may be reproduced or transmitted in any form or by any means without
prior written consent of Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS
MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the furnishing, performance, or
use of this material.
The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained
herein.
i
Contents
Basic CLI commands ···················································································································································· 1
command-alias enable·············································································································································1
command-alias mapping ·········································································································································1
display | { begin | exclude | include }·················································································································2
display | by-linenum ················································································································································3
display > ···································································································································································4
display >>·································································································································································5
display command-alias ············································································································································6
display history-command ·········································································································································6
display history-command all····································································································································7
display hotkey···························································································································································7
hotkey ········································································································································································9
quit ·············································································································································································9
return······································································································································································· 10
screen-length disable············································································································································· 10
system-view ···························································································································································· 11
Login management commands ·································································································································12
activation-key ························································································································································· 12
authentication-mode ·············································································································································· 13
auto-execute command ········································································································································· 15
command accounting············································································································································ 16
command authorization········································································································································ 17
databits··································································································································································· 18
display line····························································································································································· 18
display telnet client················································································································································ 20
display user-interface ············································································································································ 20
display users ·························································································································································· 22
escape-key······························································································································································ 23
flow-control····························································································································································· 24
free line··································································································································································· 25
free user-interface ·················································································································································· 26
history-command max-size ··································································································································· 27
idle-timeout ····························································································································································· 28
line ·········································································································································································· 28
line class································································································································································· 29
lock·········································································································································································· 31
parity······································································································································································· 32
protocol inbound ··················································································································································· 32
screen-length ·························································································································································· 33
send ········································································································································································ 34
set authentication password································································································································· 35
shell········································································································································································· 36
speed ······································································································································································ 37
stopbits···································································································································································· 37
telnet ······································································································································································· 38
telnet client source ················································································································································· 39
telnet ipv6······························································································································································· 40
telnet server acl······················································································································································ 41
ii
telnet server dscp··················································································································································· 41
telnet server enable ··············································································································································· 42
telnet server ipv6 acl············································································································································· 43
telnet server ipv6 dscp ·········································································································································· 44
terminal type ·························································································································································· 44
user-interface·························································································································································· 45
user-interface class ················································································································································ 46
user-role ·································································································································································· 47
RBAC commands ·······················································································································································49
description······························································································································································ 49
display role ···························································································································································· 49
display role feature ··············································································································································· 51
display role feature-group ···································································································································· 55
feature····································································································································································· 57
interface policy deny ············································································································································ 58
permit interface······················································································································································ 59
permit vlan ····························································································································································· 61
permit vpn-instance ··············································································································································· 62
role·········································································································································································· 63
role default-role enable········································································································································· 64
role feature-group·················································································································································· 65
rule ·········································································································································································· 66
super ······································································································································································· 69
super authentication-mode···································································································································· 70
super password ····················································································································································· 71
vlan policy deny ···················································································································································· 72
vpn-instance policy deny ······································································································································ 73
FTP commands····························································································································································75
FTP server commands ···················································································································································· 75
display ftp-server···················································································································································· 75
display ftp-user······················································································································································· 75
free ftp user ···························································································································································· 76
free ftp user-ip ························································································································································ 77
free ftp user-ip ipv6 ··············································································································································· 77
ftp server acl ·························································································································································· 78
ftp server dscp ······················································································································································· 79
ftp server enable···················································································································································· 79
ftp server ipv6 dscp··············································································································································· 80
ftp server ssl-server-policy ····································································································································· 80
ftp timeout······························································································································································· 81
FTP client commands······················································································································································ 82
append ··································································································································································· 82
ascii········································································································································································· 82
binary ····································································································································································· 83
bye ·········································································································································································· 84
cd ············································································································································································ 84
cdup········································································································································································ 85
close········································································································································································ 86
debug ····································································································································································· 86
delete ······································································································································································ 87
dir············································································································································································ 88
disconnect ······························································································································································ 89
display ftp client source ········································································································································ 90
iii
ftp ············································································································································································ 90
ftp client source······················································································································································ 91
ftp client ipv6 source············································································································································· 92
ftp ipv6 ··································································································································································· 93
get ··········································································································································································· 94
help ········································································································································································· 95
lcd ··········································································································································································· 96
ls·············································································································································································· 96
mkdir······································································································································································· 98
newer······································································································································································ 98
open········································································································································································ 99
passive···································································································································································· 99
put ·········································································································································································100
pwd·······································································································································································101
quit ········································································································································································102
reget······································································································································································102
rename··································································································································································103
reset ······································································································································································103
restart····································································································································································104
rhelp······································································································································································104
rmdir ·····································································································································································106
rstatus····································································································································································107
status ·····································································································································································109
system ···································································································································································109
user ·······································································································································································110
verbose ·································································································································································111
? ············································································································································································111
TFTP commands······················································································································································· 113
tftp ·········································································································································································113
tftp client source···················································································································································114
tftp ipv6 ································································································································································115
tftp client ipv6 source··········································································································································117
tftp-server acl························································································································································118
tftp-server ipv6 acl ···············································································································································118
File system management commands ····················································································································· 120
cd ··········································································································································································120
copy ······································································································································································121
delete ····································································································································································123
dir··········································································································································································124
file prompt ····························································································································································125
fixdisk····································································································································································126
format····································································································································································126
gunzip···································································································································································127
gzip·······································································································································································128
md5sum ································································································································································128
mkdir·····································································································································································129
more······································································································································································130
move ·····································································································································································130
pwd·······································································································································································131
rename··································································································································································131
reset recycle-bin···················································································································································132
rmdir ·····································································································································································133
sha256sum ··························································································································································133
iv
tar create ······························································································································································134
tar extract ·····························································································································································135
tar list ····································································································································································136
undelete································································································································································136
Configuration file management commands ·········································································································· 138
archive configuration ··········································································································································138
archive configuration interval ····························································································································138
archive configuration location ···························································································································139
archive configuration max··································································································································141
backup startup-configuration······························································································································142
configuration encrypt ··········································································································································142
configuration replace file····································································································································143
display archive configuration·····························································································································144
display current-configuration······························································································································145
display current-configuration diff ·······················································································································146
display default-configuration······························································································································147
display diff ···························································································································································148
display saved-configuration ·······························································································································150
display startup ·····················································································································································151
display this ···························································································································································152
reset saved-configuration····································································································································153
restore startup-configuration·······························································································································154
save·······································································································································································155
startup saved-configuration ································································································································157
Software upgrade commands································································································································ 159
boot-loader file·····················································································································································159
boot-loader update··············································································································································160
bootrom update ···················································································································································161
display boot-loader ·············································································································································162
display install active············································································································································163
display install committed ····································································································································164
install activate ······················································································································································166
install commit ·······················································································································································167
install deactivate··················································································································································167
Emergency shell commands ··································································································································· 169
copy ······································································································································································169
delete ····································································································································································169
dir··········································································································································································170
display copyright·················································································································································172
display install package·······································································································································172
display interface m-eth0 ·····································································································································173
display ip routing-table ·······································································································································175
display ipv6 routing-table···································································································································176
display version·····················································································································································177
format····································································································································································177
ftp ··········································································································································································177
install load····························································································································································178
interface m-eth0···················································································································································179
ip address ····························································································································································179
ip gateway ···························································································································································180
ipv6 address ························································································································································181
ipv6 gateway·······················································································································································181
mkdir·····································································································································································182
v
more······································································································································································182
move ·····································································································································································183
ping·······································································································································································183
ping ipv6······························································································································································185
pwd·······································································································································································185
quit ········································································································································································186
reboot ···································································································································································186
reset ssh public-key··············································································································································186
rmdir ·····································································································································································187
shutdown ······························································································································································188
ssh2·······································································································································································188
system-view ··························································································································································189
telnet ·····································································································································································190
tftp ·········································································································································································190
Device management commands ···························································································································· 191
clock datetime······················································································································································191
clock protocol ······················································································································································192
clock summer-time ···············································································································································192
clock timezone·····················································································································································194
command······························································································································································195
copyright-info enable ··········································································································································196
display clock ························································································································································197
display copyright·················································································································································198
display cpu-usage················································································································································198
display cpu-usage configuration························································································································199
display cpu-usage history ···································································································································200
display device······················································································································································202
display device manuinfo·····································································································································203
display diagnostic-information ···························································································································204
display memory ···················································································································································205
display memory-threshold···································································································································206
display scheduler job··········································································································································207
display scheduler logfile·····································································································································208
display scheduler reboot ····································································································································209
display scheduler schedule·································································································································209
display system-working-mode·····························································································································210
display transceiver alarm ···································································································································211
display transceiver diagnosis·····························································································································213
display transceiver interface ······························································································································214
display transceiver manuinfo ·····························································································································215
display version·····················································································································································216
display version-update-record ····························································································································216
header ··································································································································································217
job·········································································································································································219
memory-threshold ················································································································································219
memory-threshold usage ·····································································································································220
monitor cpu-usage enable ··································································································································221
monitor cpu-usage interval ·································································································································222
monitor cpu-usage threshold ······························································································································223
password-recovery enable ·································································································································223
reboot ···································································································································································224
reset scheduler logfile ·········································································································································225
reset version-update-record ································································································································226
restore factory-default··········································································································································226
vi
scheduler job ·······················································································································································227
scheduler logfile size···········································································································································228
scheduler reboot at ·············································································································································228
scheduler reboot delay ·······································································································································229
scheduler schedule ··············································································································································230
shutdown-interval·················································································································································231
sysname································································································································································232
system-working-mode ··········································································································································232
time at···································································································································································233
time once······························································································································································234
time repeating······················································································································································235
user-role ································································································································································237
Tcl commands·························································································································································· 239
tclsh·······································································································································································239
tclquit ····································································································································································239
Python commands ··················································································································································· 241
python···································································································································································241
python filename ···················································································································································241
Support and other resources ·································································································································· 243
Contacting HP ······························································································································································243
Subscription service ············································································································································243
Related information······················································································································································243
Documents····························································································································································243
Websites·······························································································································································243
Conventions ··································································································································································244
Index ········································································································································································ 246
1
Basic CLI commands
command-alias enable
Use command-alias enable to enable the command keyword alias function.
Use undo command-alias enable to disable the command keyword alias function.
Syntax
command-alias enable
undo command-alias enable
Default
The command keyword alias function is disabled.
Views
System view
Predefined user roles
network-admin
Usage guidelines
Configured command keyword aliases take effect only when the command keyword alias function is
enabled.
Disabling the command keyword alias function does not delete configured aliases.
Examples
# Enable the command keyword alias function.
<Sysname> system-view
[Sysname] command-alias enable
Related commands
•command-alias mapping
•display command-alias
command-alias mapping
Use command-alias mapping to configure a command keyword alias.
Use undo command-alias mapping to delete a command keyword alias.
Syntax
command-alias mapping cmdkey alias
undo command-alias mapping cmdkey
Default
A command keyword has no alias.
2
Views
System view
Predefined user roles
network-admin
Parameters
cmdkey: Specifies the first keyword of a non-undo command or the second keyword of an undo
command. You must enter the keyword in its complete form.
alias: Specifies an alias for the keyword, a string of 1 to 20 characters. It must be different from the first
keyword of any non-undo command and the second keyword of any undo command.
Usage guidelines
You can configure an alias for the first keyword of a non-undo command or the second keyword of an
undo command. Then, when you execute a command that starts with the keyword or the undo keyword
plus the keyword, you can use the alias. For example, if you configure show as the alias for the display
keyword, you can enter show clock to execute the display clock command.
To use configured command keyword aliases, make sure the command-alias enable command is
configured.
Examples
# Define show as the alias of the display keyword.
<Sysname> system-view
[Sysname] command-alias mapping display show
Related commands
•command-alias enable
•display command-alias
display | { begin | exclude | include }
Use display | { begin | exclude | include } to filter the output from a display command with a regular
expression.
Syntax
display command |{ begin | exclude | include } regular-expression
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
command: Specifies the keywords and arguments of a display command. To display available keywords
and arguments, enter display ?.
begin: Displays the first line matching the specified regular expression and all subsequent lines.
exclude: Displays all lines not matching the specified regular expression.
3
include: Displays all lines matching the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Usage guidelines
Use the | { begin | exclude | include } regular-expression option with a display command to filter the
command output. For more information about regular expressions, see Fundamentals Configuration
Guide.
Examples
# Display the lines that contain "vlan" in the running configuration.
<Sysname> display current-configuration | include vlan
vlan 1
vlan 999
port access vlan 999
display | by-linenum
Use display | by-linenum to number each output line for a display command.
Syntax
display command |by-linenum
Views
Any view
Predefined user roles
network-admin
Parameters
command: Specifies the keywords and arguments of a display command. To display available keywords
and arguments, enter display ?.
Usage guidelines
By numbering each output line from a display command, you can easily identify the lines of interest.
Each line number is displayed as a 5-character string and might be followed by a colon (:) or hyphen (-).
If you specify the | by-linenum option and the | begin regular-expression option for a display command,
a hyphen is displayed for all lines that do not match the regular expression.
Examples
# Display VLAN 999 settings, with each output line identified by a number.
<Sysname> display vlan 999 | by-linenum
1: VLAN ID: 999
2: VLAN type: Static
3: Route interface: Configured
4: IP address: 192.168.2.1
5: Subnet mask: 255.255.255.0
6: Description: For LAN Access
7: Name: VLAN 0999
8: Tagged ports: None
9: Untagged ports:
4
10: Ten-GigabitEthernet1/1/5
# Display the first line that begins with "user-group" in the running configuration and all of the following
lines.
<Sysname> display current-configuration | by-linenum begin user-group
114: user-group system
115- #
116- return
display >
Use display >to save the output from a display command to a separate file.
Syntax
display command > filename
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
command: Specifies the keywords and arguments of a display command. To display available keywords
and arguments, enter display ?.
filename: Specifies the name of the file that is used to save the output, a string of 1 to 63 characters.
Usage guidelines
The display commands show the configuration, statistics, and states of the device. You can use the
display >command to save the output to a file.
If the specified file does not exist, the system creates the file and saves the output to the file. If the file
already exists, the system overwrites the file.
Examples
# Save VLAN 1 settings to a separate file named vlan.txt.
<Sysname> display vlan 1 > vlan.txt
# Verify the content of the vlan.txt file.
<Sysname> more vlan.txt
VLAN ID: 1
VLAN type: Static
Route interface: Not configured
Description: VLAN 0001
Name: VLAN 0001
Tagged ports: None
Untagged ports:
Ten-GigabitEthernet1/1/6
5
display >>
Use display >> to append the output from a display command to the end of a file.
Syntax
display command >> filename
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
command: Specifies the keywords and arguments of a display command. To display available keywords
and arguments, enter display ?.
filename: Specifies the name of the file that is used to save the output, a string of 1 to 63 characters.
Usage guidelines
The display commands show the configuration, statistics, and states of the device. You can use display >>
to save the output to a file.
If the specified file does not exist, the system creates the file and saves the output to the file. If the file
already exists, the system appends the output to the end of the file.
Examples
# Append the VLAN 999 settings to the end of the vlan.txt file.
<Sysname> display vlan 999 >> vlan.txt
<Sysname>
# Check the content of the vlan.txt file.
<Sysname> more vlan.txt
VLAN ID: 1
VLAN type: Static
Route interface: Not configured
Description: VLAN 0001
Name: VLAN 0001
Tagged ports: None
Untagged ports:
Ten-GigabitEthernet1/1/6
VLAN ID: 999
VLAN type: Static
Route interface: Configured
IP address: 192.168.2.1
Subnet mask: 255.255.255.0
Description: For LAN Access
Name: VLAN 0999
Tagged ports: None
Untagged ports:
6
Ten-GigabitEthernet1/1/5
display command-alias
Use display command-alias to display the status of the command keyword alias function and the
configured command keyword alias.
Syntax
display command-alias
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display command keyword alias information.
<Sysname> display command-alias
Command alias is enabled
Index Alias Command key
1 ping1 ping
2 ssh1 ssh
Related commands
•command-alias enable
•command-alias mapping
display history-command
Use display history-command to display all commands that are saved in the command history buffer for
the current CLI session.
Syntax
display history-command
Views
Any view
Predefined user roles
network-admin
network-operator
Usage guidelines
The system automatically saves commands you have successfully executed to the command history buffer
for the current CLI session. You can view them and execute them again.
By default, the system can save up to 10 commands in the buffer. You can use the history-command
max-size command to change the buffer size.
7
Examples
# Display all commands saved in the command history buffer for the current CLI session.
<Sysname> display history-command
system-view
vlan 2
quit
Related commands
history-command max-size
display history-command all
Use display history-command all to display all commands saved in the command history buffer for all
CLI sessions.
Syntax
display history-command all
Views
Any view
Predefined user roles
network-admin
network-operator
Usage guidelines
The system automatically saves commands successfully executed by users to the command history buffer
for all CLI sessions. Users can view them and execute them again.
Up to 1024 commands can be saved in the command history buffer. When this number is reached, the
system deletes the earliest commands to make room for newly executed commands.
Examples
# Display all commands saved in the command history buffer for all CLI sessions.
<Sysname> display history-command all
Date Time Terminal Ip User
03/16/2012 20:03:33 vty0 192.168.1.26 **
Cmd:dis his all
03/16/2012 20:03:29 vty0 192.168.1.26 **
Cmd:sys
Related commands
display history-command
display hotkey
Use display hotkey to display hotkey information.
Syntax
display hotkey
8
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display hotkey information.
<Sysname> display hotkey
----------------- Hotkeys -----------------
-Defined command hotkeys-
CTRL_G display current-configuration
CTRL_L display ip routing-table
CTRL_O undo debugging all
-Undefined command hotkeys-
CTRL_T NULL
CTRL_U NULL
-System-reserved hotkeys-
CTRL_A Move the cursor to the beginning of the line.
CTRL_B Move the cursor one character to the left.
CTRL_C Stop the current command.
CTRL_D Erase the character at the cursor.
CTRL_E Move the cursor to the end of the line.
CTRL_F Move the cursor one character to the right.
CTRL_H Erase the character to the left of the cursor.
CTRL_K Abort the connection request.
CTRL_N Display the next command in the history buffer.
CTRL_P Display the previous command in the history buffer.
CTRL_R Redisplay the current line.
CTRL_V Paste text from the clipboard.
CTRL_W Delete the word to the left of the cursor.
CTRL_X Delete all characters from the beginning of the line to the cursor.
CTRL_Y Delete all characters from the cursor to the end of the line.
CTRL_Z Return to the User View.
CTRL_] Kill incoming connection or redirect connection.
ESC_B Move the cursor back one word.
ESC_D Delete all characters from the cursor to the end of the word.
ESC_F Move the cursor forward one word.
ESC_N Move the cursor down a line.
ESC_P Move the cursor up a line.
ESC_< Move the cursor to the beginning of the clipboard.
ESC_> Move the cursor to the end of the clipboard.
Related commands
hotkey
9
hotkey
Use hotkey to assign a command to a configurable hotkey.
Use undo hotkey to restore the default.
Syntax
hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U } command
undo hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U }
Default
•Ctrl_G: display current-configuration (display the running configuration).
•Ctrl_L: display ip routing-table (display the IPv4 routing table information).
•Ctrl_O: undo debugging all (disable all debugging functions).
•Ctrl_T: No command is assigned to this hotkey.
•Ctrl_U: No command is assigned to this hotkey.
Views
System view
Predefined user roles
network-admin
Parameters
CTRL_G: Assigns a command to Ctrl+G.
CTRL_L: Assigns a command to Ctrl+L.
CTRL_O: Assigns a command to Ctrl+O.
CTRL_T: Assigns a command to Ctrl+T.
CTRL_U: Assigns a command to Ctrl+U.
command: Specifies the command to be assigned to the hotkey.
Usage guidelines
The system defines some hotkeys and provides five configurable command hotkeys. Pressing a hotkey
executes the command assigned to the hotkey.
To display system-defined and configurable hotkeys, use the display hotkey command.
Examples
# Assign the display tcp status command to the hotkey Ctrl+T.
<Sysname> system-view
[Sysname] hotkey ctrl_t display tcp status
Related commands
display hotkey
quit
Use quit to return to the upper-level view.
10
Syntax
quit
Views
Any view
Predefined user roles
network-admin
network-operator
Usage guidelines
Executing this command in user view disconnects you from the device.
Examples
# Return from Ten-GigabitEthernet 1/1/5 interface view to system view and then to user view.
[Sysname- Ten-GigabitEthernet1/1/5] quit
[Sysname] quit
<Sysname>
return
Use return to return to user view from any other view.
Syntax
return
Views
Any view except user view
Predefined user roles
network-admin
network-operator
Usage guidelines
Pressing Ctrl+Z has the same effect as the return command.
Examples
# Return to user view from Ten-GigabitEthernet 1/1/5 interface view.
[Sysname- Ten-GigabitEthernet1/1/5] return
<Sysname>
screen-length disable
Use screen-length disable to disable pausing between screens of output for the current session.
Use undo screen-length disable to enable pausing between screens of output for the current session.
Syntax
screen-length disable
undo screen-length disable
11
Default
The default depends on the configuration of the screen-length command in user line view.
The following are default settings for the screen-length command:
•Pausing between screens of output.
•Displaying up to 24 lines on a screen.
Views
User view
Predefined user roles
network-admin
Usage guidelines
If you disable pausing between screens of output, all output is displayed. The screen is refreshed
continuously until the final screen is displayed.
This command takes effect only for the current session. When you are logged out, the default is restored.
Examples
# Disable pausing between screens of output for the current session.
<Sysname> screen-length disable
Related commands
screen-length
system-view
Use system-view to enter system view from user view.
Syntax
system-view
Views
User view
Predefined user roles
network-admin
network-operator
Examples
# Enter system view from user view.
<Sysname> system-view
System View: return to User View with Ctrl+Z.
[Sysname]
12
Login management commands
The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features,
commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about
FIPS mode, see Security Configuration Guide.
Some login management commands are available in both user line view and user line class view:
•A setting in user line view is applied only to the user line. A setting in user line class view is applied
to all user lines of the class.
•A non-default setting in either view takes precedence over a default setting in the other view. A
non-default setting in user line view takes precedence over a non-default setting in user line class
view.
•A setting in user line view takes effect immediately and affects the online user. A setting in user line
class view does not affect online users and takes effect only for users who log in after the
configuration is completed.
Some login management commands are not supported in some user line views but can be configured in
the corresponding user line class views. However, the commands do not take effect. This chapter provides
only remarks about commands that are not supported in user line view.
activation-key
Use activation-key to define a shortcut key for starting a terminal session.
Use undo activation-key to restore the default.
Syntax
activation-key character
undo activation-key
Default
Pressing Enter starts a terminal session.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
character: Specifies the shortcut key. It can be a string of 1 to 3 characters, or an ASCII code value in the
range of 0 to 127. If you enter a number that is greater than 127, or enter a string that is not a number,
the first character is used as the shortcut key. For example, if you configure activation-key 987, the
shortcut key is 9. If you configure activation-key abc, the shortcut key is a.
Usage guidelines
This command is not supported in VTY line view or VTY line class view.
This command is available in both user line view and user line class view:
Other manuals for 6125XLG
36
Table of contents
Other HP Switch manuals
HP
HP 12500 Series User instructions
HP
HP 10500 series User manual
HP
HP 1405-16 Specification sheet
HP
HP ProCurve 6600-24XG Assembly instructions
HP
HP PROCURVE 6120 User manual
HP
HP Aruba Instant On 1430 5G Assembly instructions
HP
HP A5800-48G User instructions
HP
HP ProCurve 8108fl User manual
HP
HP StorageWorks 2/8-EL - SAN Switch Instruction Manual
HP
HP 571956-B21 User manual
HP
HP 2520 Series User instructions
HP
HP A-RPS800 Instruction Manual
HP
HP ProCurve 4148 User manual
HP
HP aruba 9300-32D Series User manual
HP
HP P2361AA #ABA User manual
HP
HP HP 2530 User manual
HP
HP bh5700 User manual
HP
HP StorageWorks 8/40 - SAN Switch Quick user guide
HP
HP StorageWorks edge switch 2/32 User manual
HP
HP PROCURVE 2910AL User manual
Popular Switch manuals by other brands
Hydropa
Hydropa HYDROSTAR DS-4 7 Series manual
ZooZ
ZooZ ZEN15 800LR user manual
METRObility Optical Systems
METRObility Optical Systems CenturyStack 8124-01-M Installation and user guide
GE Zenith Controls
GE Zenith Controls ZTX Operation and maintenance manual
IBM
IBM RackSwitch G8264CS installation guide
Edge-Core
Edge-Core ES4005V installation guide
Plexxi
Plexxi 2 Getting started guide
Extreme Networks
Extreme Networks Alpine 3802 Hardware installation guide
Nortel
Nortel WLAN 2300 Series Installation and configuration guide
D-Link
D-Link DGS-1008T reference guide
LevelOne
LevelOne GEP-0823 user manual
ANTAIRA
ANTAIRA LMX-1600G Series Quick installation guide
