Huawei MAP05A1 User manual

iSitePower-M V100R002C00
(MAP05A1, MAB05B1)
Quick Guide
Huawei Digital Power Technologies Co., Ltd.
Issue: 04
Date: 2022-07-15

1
System Description
Single Product System (Typical Scenario)
Single Product System (Capacity Expansion Scenario)
1

2
Parallel System
Overview
•A maximum of three power modules can be connected in parallel. The following figure
shows two power modules in parallel.
•In parallel connection scenarios, the number of battery modules on the master and slave
products must be the same.
(A) PV string
(B) DC switch
(C) AC Parallel Box
(D)
PDB
(E) Load
(F) DG
(G) Power grid
(H) Power grid
(I)
PDC
Scenario
Number of Power Modules Number of Battery Modules Capacity
Single product
1 1 3kVA/5kW
2 6kVA/10kW
3 6kVA/15kW
Single Product
(Capacity
Expansion
Scenario)
4 6kVA/20kW
5 6kVA/25kW
6 6kVA/30kW
Parallel
products
2 2 10.8kVA/10kW
4 10.8kVA/20kW
6 10.8kVA/30kW
3 3 16.2kVA/15kW
6 16.2kVA/30kW
9 16.2kVA/45kW

3
2Overview
The iSitePower-M is a fuel-free hybrid power solution for areas with no or poor mains supply.
Base
Power module
Battery
modules
Heat sink
LED indicator
Note: The 15 kWh model is used as an example.
(1) PV maintenance
switch (DC SWITCH)
(2) PV inputs
(3) Power parallel ports
for battery modules
(4) COM
-PAR port
(5) COM
-BAT port
(6) Wireless
backhaul module
port
(7)
Maintenance
compartment door
(8)
Ground point
(9) AC input
(10)
AC output
(11) Reserved ports
(12) DIP switch
(13) FE ports
(14) COM port and
dry contacts
(15) WiFi button
(16) Manual ON/OFF
switch
iSitePower-M
2.1
Power Module
2.2
Left view Right view (door opened)
Decorative
cover
Right view

4
(1) Alignment
boss
(2) COM port
(3) Terminals
for battery
module
cascading
(4) Heat sink
(5) Ground
points
Battery Module
2.3
(1) Ground
point on the
door
(2) Ground
bar
(3) Cable bags
(4)
AC input
circuit breaker
(5) N wiring
terminal
(6) AC output
circuit breaker
AC Parallel Box
2.4
Left view Right view
3Installation Preparations
Installation Environment Requirements
3.1
If a battery module is dropped or violently impacted during installation, it may become
faulty and cannot be used. Using a faulty module will cause safety risks such as cell leakage
and electric shock.
Wall and Ground Requirements
3.2
•The product can be mounted on a concrete wall or brick wall and cannot be mounted on a
sandwich panel wall or a wooden wall.
•The bearing capacity of the ground must be greater than or equal to 500 kg/m2.

5
Installation Tools
3.3
Hammer drill Insulated torque socket
wrench (including an
extension bar)
Adjustable torque
wrench
Diagonal pliers Wire stripper
Flat-head insulated
torque screwdriver
Rubber mallet Utility knife Cable cutter
Crimping tool,
model: PV-CZM-
CZM41100
(preferred)/CZM22
100
Cord end terminal
crimping tool
Removal tool
(model: PV-MS-HZ
open-end wrench)
Cable tie Vacuum cleaner
Multimeter (DC voltage
measurement range ≥
600 V DC)
Marker
Heat gun Protective gloves Goggles Anti-dust mask
Work shoes
Steel measuring tape Level Hydraulic pliers
Heat shrink tubing
Phillips insulated
torque screwdriver

6
Installation Dimensions
3.4
Single Product Scenario
Parallel Connection or Capacity Expansion Scenarios
(Top view)
(Top view)

7
4Installing a Mounting Bracket
Ground Mounting
Two marking out templates are required for
ground mounting. A small marking out
template determines holes on the ground, and
a large marking out template determines
holes on the wall.
1. Cut the marking out template along the
dotted line.
3. Mark the mounting holes
for battery modules.
4. Drill holes and install expansion
bolts.
The base must be secured to the ground
using bolts. Otherwise, the device may tip
over, causing personal injury or device
damage.
2. Install the mounting base.
Level
Marking out
template

8
Wall Mounting
3. Install the wall-mounting base.
2. Drill holes and install expansion
bolts.
1. Mark the mounting holes for
the wall-mounting base and
battery modules.

9
5Installing Modules
Installing Battery Modules and Power Modules
5.1
•Two persons are required to move a module.
•Battery modules must be secured to the wall.
1. Install a battery module on the
mounting base.
This section describes how to install
modules in the ground mounting scenario.
2. Secure the battery module to the wall.
3. Install a wall-mounting base cover.
In the wall-mounting scenario,
install battery modules before
installing the wall-mounting
base cover.