Huawei FusionModule2000 V500R003C10 User manual

FusionModule2000 Smart Modular Data Center
V500R002C03
Installation Guide
Issue
02
Date
2018-03-31
HUAWEI TECHNOLOGIES CO., LTD.

Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
i
Copyright © Huawei Technologies Co., Ltd. 2018. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://e.huawei.com

FusionModule2000 Smart Modular Data Center
Installation Guide
About This Document
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
ii
About This Document
Purpose
This document describes the site requirements for installing the FusionModule2000 smart
modular data center (FusionModule2000 for short) as well as the methods for installing
cabinets, devices, and cables, providing installation guidance and technical support for onsite
installation personnel and technical support engineers.
Intended Audience
This document is intended for:
Hardware installation engineers
Commissioning engineers
Maintenance engineers
Technical support engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Indicates an imminently hazardous situation which, if
not avoided, will result in serious injury or death.
Indicates a potentially hazardous situation which, if not
avoided, could result in serious injury or death.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to
personal injury.
Calls attention to important information, best practices
and tips.

FusionModule2000 Smart Modular Data Center
Installation Guide
About This Document
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iii
Symbol
Description
NOTE is used to address information not related to
personal injury, equipment damage, or environment
deterioration.
Change History
Changes between document issues are cumulative. The latest document issue contains all
updates made in previous issues.
Issue 02 (2018-03-31)
Updated the section "(Optional) Installing a 600 mm Wide Air Conditioner Enclosure Frame."
Issue 01 (2017-09-20)
This issue is the first release.

FusionModule2000 Smart Modular Data Center
Installation Guide
Contents
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iv
Contents
About This Document.................................................................................................................... ii
1 Safety Precautions.........................................................................................................................1
1.1 General Safety Precautions...........................................................................................................................................1
1.2 Electrical Safety............................................................................................................................................................2
1.3 Battery Safety ...............................................................................................................................................................4
1.4 Mechanical Safety ........................................................................................................................................................6
1.5 Others............................................................................................................................................................................7
2 Installation Preparations .............................................................................................................8
2.1 Precautions for Transportation and Placing ..................................................................................................................8
2.2 Unpacking and Acceptance...........................................................................................................................................9
2.3 Installation Environment Check .................................................................................................................................10
2.4 Site Requirements.......................................................................................................................................................12
2.5 Documentation Preparations.......................................................................................................................................13
2.6 Tools and Instruments.................................................................................................................................................14
2.7 Personnel Requirements .............................................................................................................................................18
2.8 Scenario Description...................................................................................................................................................18
2.8.1 Power Supply and Distribution Cabinet Scenario (Dual-Row) ...............................................................................19
2.8.2 Power Supply and Distribution Cabinet Scenario (Single-Row).............................................................................20
2.8.3 Smart Busway Scenario (Dual-Row).......................................................................................................................21
2.8.4 Smart Busway Scenario (Single-Row) ....................................................................................................................22
3 Smart Module Layout Requirements......................................................................................24
3.1 Layout Requirements for Standard Dual-Row Aisle Containment.............................................................................24
3.2 Layout Requirements for Standard Single-Row Aisle Containment...........................................................................25
3.3 Layout Requirements for Dual-Row Aisle Containment with a Column ...................................................................27
3.4 Layout Requirements for Single-Row Aisle Containment with a Column.................................................................33
4 (Optional) Installing Bases........................................................................................................40
4.1 Precautions for Installing Bases..................................................................................................................................40
4.2 Installing Bases with Adjustable Dimensions.............................................................................................................41
4.3 Installing Bases with Fixed Dimensions.....................................................................................................................46
4.3.1 (Optional) Adjusting Adjustable Feet of Air Conditioner Bases (300 mm Wide)....................................................46
4.3.2 (Optional) Adjusting Adjustable Feet of Air Conditioner and PDC Bases (600 mm Wide) ....................................48

FusionModule2000 Smart Modular Data Center
Installation Guide
Contents
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
v
4.3.3 Installing Bases with Fixed Dimensions..................................................................................................................50
4.4 Connecting Base Ground Cables ................................................................................................................................52
5 Installing the PDC ......................................................................................................................54
5.1 Moving the PDC.........................................................................................................................................................54
5.2 Installing a Tail Frame ................................................................................................................................................56
5.3 (Optional) Installing a Top Frame...............................................................................................................................56
6 Installing the Network Cabinet, IT Cabinet, and Battery Cabinet ...................................58
6.1 Moving the Network Cabinet, IT Cabinet, and Battery Cabinet.................................................................................58
6.2 (Optional) Installing Side Plates for IT Cabinets........................................................................................................59
6.3 (Optional) Taking out rPDU Cables............................................................................................................................61
6.4 (Optional) Taking out Industrial Connectors ..............................................................................................................61
6.5 (Optional) Adjusting Battery Cabinet Side Plates.......................................................................................................63
6.6 (Optional) Installing a Battery Cabinet Top Frame.....................................................................................................63
6.7 (Optional) Installing a Horizontal Ground Bar...........................................................................................................63
6.8 (Optional) Installing a Vertical Ground Bar................................................................................................................64
6.9 (Optional) Setting a Cabinet Code Lock.....................................................................................................................65
7 Installing Air Conditioners.......................................................................................................69
7.1 (Optional) Installing NetCol5000-A 25 kW Air Conditioners....................................................................................69
7.1.1 (Optional) Installing Top Frames (Top Pipe Routing) .............................................................................................69
7.1.2 (Optional) Installing Top Frames (Bottom Pipe Routing)........................................................................................71
7.1.3 (Optional) Installing a 300 mm Wide Air Conditioner Adaptive Frame..................................................................72
7.1.4 (Optional) Installing a Top Frame for an Adaptive Frame.......................................................................................75
7.2 (Optional) Installing NetCol5000-A 42 kW Air Conditioners....................................................................................76
7.2.1 (Optional) Installing a 600 mm Wide Air Conditioner Enclosure Frame ................................................................76
7.2.2 (Optional) Installing Top Frames (Top Pipe Routing) .............................................................................................80
7.2.3 (Optional) Installing Top Frames (Bottom Pipe Routing)........................................................................................82
7.3 Installing Air Conditioner Outdoor Units and Routing Pipes .....................................................................................82
8 Combining Cabinets...................................................................................................................83
9 Grounding Cabinets ...................................................................................................................88
10 Installing the Aisle Containment...........................................................................................92
10.1 Installing Sealing Plates (Single-Row Scenario) ......................................................................................................92
10.2 Installing Sealing Plates Around a Column (in Scenarios with a Column)...............................................................95
10.3 Installing Skylights...................................................................................................................................................97
10.3.1 Installing Control, Flat, and Rotating Skylights ....................................................................................................97
10.3.2 Installing Adjustable Skylights (in Scenarios with a Column).............................................................................100
10.3.3 (Optional) Grounding Control Skylights .............................................................................................................107
10.4 Installing the Cabinet Bottom Sealing Plate ...........................................................................................................107
10.5 Installing End Doors............................................................................................................................................... 111
10.5.1 Installing Sliding Doors (Dual-Row 2000 mm)...................................................................................................112

FusionModule2000 Smart Modular Data Center
Installation Guide
Contents
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vi
10.5.2 Installing Sliding Doors (Dual-Row 2200 mm)...................................................................................................121
10.5.3 Installing Revolving Doors (Single-Row and Dual-Row 2000 mm)...................................................................128
10.5.4 Installing Revolving Doors (Single-Row and Dual-Row 2200 mm)...................................................................140
10.6 Attaching Cabinet Labels........................................................................................................................................148
11 Installing Cable Troughs and Cable Trays ........................................................................151
11.1 (Optional) Installing Cable Troughs........................................................................................................................151
11.1.1 (Optional) Installing a New Main Way................................................................................................................151
11.1.2 Installing Cable Troughs (600 mm or 800 mm Wide)..........................................................................................151
11.1.3 Installing Cable Troughs (300 mm Wide)............................................................................................................156
11.1.4 Installing End Panels for Cable Troughs..............................................................................................................157
11.2 Installing Cable Trays .............................................................................................................................................158
11.2.1 (Optional) Installing Cable Trays (Dual-Row Aisle Containment)......................................................................158
11.2.2 Installing Cable Trays (in Scenarios with a Column) ..........................................................................................160
11.2.3 (Optional) Installing Indoor Cable Trays .............................................................................................................164
11.2.4 (Optional) Grounding Cable Trays ......................................................................................................................164
12 (Optional) Installing Aisle Lights........................................................................................165
13 (Optional) Installing Dehumidifiers...................................................................................171
14 Installing Power Supply and Distribution Devices.........................................................176
14.1 (Optional) Installing the UPS Outside the Smart Module ......................................................................................176
14.2 (Optional) Installing a Battery Cabinet Outside the Smart Module........................................................................176
14.3 (Optional) Installing Batteries.................................................................................................................................176
14.4 (Optional) Installing an Air Conditioner PDB ........................................................................................................177
15 Installing Monitoring Devices .............................................................................................179
15.1 Equipment Layout in the Network Cabinet ............................................................................................................179
15.1.1 (Optional) Installing an RH2288 Server ..............................................................................................................180
15.1.2 (Optional) Installing a VCN500...........................................................................................................................182
15.1.3 (Optional) Installing a LAN Switch.....................................................................................................................184
15.1.4 Installing an ECC800...........................................................................................................................................185
15.2 (Optional) Installing a Rack Environment Unit......................................................................................................189
15.3 Installing Monitoring Devices on a Control Skylight.............................................................................................190
15.3.1 Installing a Rotating Skylight Magnetic Lock .....................................................................................................191
15.3.2 Installing a Camera..............................................................................................................................................192
15.3.3 (Optional) Installing a Smoke Detector ...............................................................................................................196
15.3.4 (Optional) Installing Multi-Functional Sensors...................................................................................................196
15.4 Installing Monitoring Devices on the End Door.....................................................................................................198
15.4.1 Monitoring Component Layout for the Sliding Door ..........................................................................................198
15.4.2 Monitoring Component Layout for the Revolving Door (Dual-Row Scenario) ..................................................199
15.4.3 Monitoring Component Layout for the Revolving Door (Single-Row Scenario)................................................200
15.4.4 Installing an Actuator or Converter......................................................................................................................200
15.4.5 Installing an Alarm Beacon..................................................................................................................................203

FusionModule2000 Smart Modular Data Center
Installation Guide
Contents
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vii
15.4.6 (Optional) Installing a Revolving Door Magnetic Lock......................................................................................204
15.4.7 (Optional) Installing a Sliding Door Magnetic Lock ...........................................................................................208
15.4.8 Installing a Button................................................................................................................................................210
15.4.9 Installing a Monitoring Device on the Pad Mounting Kit.................................................................................... 211
15.4.9.1 (Optional) Installing a Fingerprint and Card Reader ........................................................................................213
15.4.9.2 (Optional) Installing a Fingerprint and Card Reader with a Keypad ................................................................214
15.4.9.3 (Optional) Installing a Card Reader with a Keypad..........................................................................................215
15.4.9.4 (Optional) Installing an IC Card Reader...........................................................................................................216
15.4.9.5 Installing a Pad Power Connector.....................................................................................................................218
15.4.9.6 Installing a Pad .................................................................................................................................................221
15.4.9.7 Securing the Pad Mounting Kit.........................................................................................................................222
15.5 Installing Monitoring Devices on Cable Troughs...................................................................................................225
15.5.1 Layout of Smart ETH Gateways (Dual-Row Scenario).......................................................................................225
15.5.2 Layout of Smart ETH Gateways (Single-Row Scenario) ....................................................................................226
15.5.3 Installing a Smart ETH Gateway.........................................................................................................................228
15.6 (Optional) Installing Temperature Sensors .............................................................................................................229
15.7 Rules for Deploying T/H Sensors...........................................................................................................................231
15.8 Installing a Temperature and Humidity Sensor.......................................................................................................232
15.9 Installing a WLDS900 Water Sensor ......................................................................................................................234
15.9.1 Laying Out the Water Detection Cable (Dual-Row Scenario).............................................................................235
15.9.2 Laying Out the Water Detection Cable (Single-Row Scenario)...........................................................................237
15.9.3 Connecting a Cable to the WLDS900 Water Sensor............................................................................................238
15.9.4 Routing a Water Detection Cable.........................................................................................................................240
15.10 Installing a GSM Modem .....................................................................................................................................242
16 (Optional) Installing In-Room Access Control Devices and Cameras .........................244
16.1 Layout of the In-Room Access Control System......................................................................................................244
16.2 (Optional) Installing an In-Room Access Actuator.................................................................................................246
16.3 (Optional) Installing an In-Room Double Door Magnetic Lock.............................................................................250
16.4 (Optional) Installing an In-Room Single Door Magnetic Lock..............................................................................253
16.5 (Optional) Installing an In-Room Fingerprint and Card Reader with a Keypad.....................................................257
16.6 (Optional) Installing an In-Room Fingerprint and Card Reader.............................................................................258
16.7 (Optional) Installing an In-Room Card Reader with a Keypad ..............................................................................260
16.8 (Optional) Installing an In-Room Exit Button........................................................................................................261
16.9 (Optional) Installing an In-Room Emergency Door Release Button ......................................................................262
16.10 (Optional) Installing an In-Room Camera ............................................................................................................264
17 Connecting Cables ..................................................................................................................267
17.1 System Cabling Rules.............................................................................................................................................267
17.2 Cable Connection Process ......................................................................................................................................272
17.3 Cable Routes for the Dual-Row Aisle Containment Scenario (Power Supply and Distribution Cabinet)..............273
17.4 Cable Routes for the Single-Row Aisle Containment Scenario (Power Supply and Distribution Cabinet)............274
17.5 Cable Routes for the Dual-Row Aisle Containment Scenario (Smart Busway) .....................................................275

FusionModule2000 Smart Modular Data Center
Installation Guide
Contents
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
viii
17.6 Cable Routes for the Single-Row Aisle Containment Scenario (Smart Busway)...................................................277
17.7 (Optional) Cable Routing for the Air Conditioner PDB .........................................................................................278
17.8 Connecting Cables to the Power Supply and Distribution System .........................................................................278
17.8.1 Connecting Cables to Power Supply and Distribution Devices...........................................................................278
17.8.2 Connecting Battery Cables ..................................................................................................................................279
17.8.3 (Optional) Connecting Cables to Industrial Connectors ......................................................................................284
17.8.4 (Optional) Connecting rPDU Cables ...................................................................................................................285
17.9 Connecting Cables to the Cooling System..............................................................................................................289
17.10 Installing Cables for the Facility Management System ........................................................................................289
17.11 Cable Routes for the Aisle Lighting System.........................................................................................................289
17.12 (Optional) Connecting Cables for the In-Room Access Control and Camera System..........................................290
A Appendix ...................................................................................................................................293
A.1 Installing an Expansion Bolt....................................................................................................................................293
A.2 Cable Routes Inside an IT Cabinet...........................................................................................................................294
A.3 Preparing a Monitoring Cable..................................................................................................................................299
A.4 (Optional) Connecting Linkage Cables Between the Gas Extinguishing Controller and Equipment Room ATS ...300
A.5 (Optional) Connecting Linkage Cables Between the Equipment Room Fire Extinguishing System and Access
Actuator..........................................................................................................................................................................302
B Common Screw Torques.........................................................................................................303
C Installation Verification..........................................................................................................305
D Acronyms and Abbreviations................................................................................................308

FusionModule2000 Smart Modular Data Center
Installation Guide
1 Safety Precautions
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1
1 Safety Precautions
1.1 General Safety Precautions
This section describes safety precautions for installing, operating, and maintaining a smart
module.
Declaration
Huawei will not be liable for any consequences of the following scenarios:
Running in conditions not specified in this manual.
Installation or use in environments which are not specified in related international
standards.
Unauthorized modifications to the product or software code.
Operations not complying with the operation instructions and safety precautions in this
document.
Device damage due to abnormal natural factors.
Overview
To ensure safety of humans and the equipment, pay attention to the safety symbols on the
equipment and all the safety instructions in this document.
The "NOTICE", "WARNING", "CAUTION", and "DANGER" marks in this document do not
represent all the safety instructions. They are only supplements to the safety instructions.
Local Safety Regulations
When operating the equipment, you must follow local laws and regulations. The safety
instructions in this document are only supplements to the local laws and regulations.
Personal Requirements
Only trained and qualified personnel are allowed to install, operate, and maintain Huawei
equipment, and they must understand basic safety precautions to avoid hazards.
Only trained and qualified personnel are allowed to install, operate, and maintain the
equipment.

FusionModule2000 Smart Modular Data Center
Installation Guide
1 Safety Precautions
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
2
Only trained and qualified personnel are allowed to remove safety facilities and inspect
the equipment.
Only personnel certified or authorized by Huawei are allowed to replace or change the
equipment or components (including software).
Installation personnel must report faults or errors that might cause serious safety issues
to related owners.
Grounding Requirements
Equipment to be grounded must meet the following requirements:
When installing the equipment, always ground the device first. Disconnect the ground
cable at the end of removing the device.
Do not damage the ground conductor.
Do not operate the device in the absence of a properly installed ground conductor.
Conduct the electrical inspection carefully.
The device (or system) must be connected permanently to the protection ground before
an operation. Before operating the device, check the electrical connection of the device
to ensure that it is securely grounded.
Human Safety
Before operating a device, wear electrostatic discharge (ESD) clothes, ESD gloves, and
an ESD wrist strap. Do not wear jewelry or watches when you operate the device.
In the case of fire, immediately leave the building or the equipment room, and turn on
the fire alarm bell or make an emergency call. Do not enter a building that is on fire.
Wear a helmet and safety belt when working at heights. Ensure that the safety belt is
properly connected when working at heights over 2000 mm above the ground. Set the
warning zone and place warning signs under the working spot.
Equipment Safety
The device must be fixed securely on the floor or to other immovable objects such as
walls and mounting racks before operation.
Do not block the ventilation vents while the system is operating.
Tighten the thumbscrews by using a tool after initial installation and subsequent access
to the panel.
After the installation, remove packing materials from the equipment area.
1.2 Electrical Safety
This section describes the precautions to be taken in terms of electrical safety.
High Voltage

FusionModule2000 Smart Modular Data Center
Installation Guide
1 Safety Precautions
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3
Devices are powered by high-voltage power source. Direct or indirect contact (through
damp objects) with the power source may result in serious injury.
Non-standard and improper operations under high voltage may result in fire and electric
shocks.
High Electrical Leakage
Ground the device before powering it on. Otherwise, personal injury or device damage may
be caused by high leakage current.
If a "high electrical leakage" tag is present on the power terminal of the device, you must
ground the device before powering it on.
Power Cable
Do not install or remove power cables when the device is on. Transient contact between the
core of the power cable and the conductor may generate electric arcs or sparks, which may
cause fire or hurt human eyes.
Before installing or removing the power cable, turn off the power switch.
Before connecting a power cable, verify that the label on the power cable is correct.
Electrostatic Discharge
The static electricity generated by human bodies may damage the electrostatic-sensitive
components on boards, for example, the large-scale integrated (LSI) circuits.
Human body movement, friction between human bodies and clothes, friction between
shoes and floors, or handling of plastic articles causes static electromagnetic fields on
human bodies. These static electromagnetic fields cannot be eliminated until the static is
discharged.
To prevent electrostatic-sensitive components from being damaged by the static on
human bodies, you must wear a well-grounded ESD wrist strap when touching the
device or handling boards or application-specific integrated circuits (ASICs).

FusionModule2000 Smart Modular Data Center
Installation Guide
1 Safety Precautions
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4
Figure 1-1 Putting on an ESD wrist strap
Neutral-Ground Voltage
It is recommended that the three-phase loads be equalized and the neutral-ground voltage be
kept at less than 2 V to meet power distribution requirements.
1.3 Battery Safety
This section describes the safety precautions for operating batteries.
Before operating batteries, read the safety precautions for battery handling and battery
connection methods carefully.
Any incorrect operation of batteries may cause danger. When operating batteries, avoid
short circuits and electrolyte overflow or leakage.
Electrolyte overflows may damage the device. It will corrode metal parts and circuit
boards, and ultimately damage the device and cause short circuits of circuit boards.
Batteries have a high power capacity. Short circuits caused by incorrect operations of
batteries can result in serious personal injury.
Preventive Measures
When installing and maintaining batteries, pay attention to the following:
Use special insulated tools.
Wear protective goggles and take other necessary protective measures.
Wear rubber gloves and a protective coat to guard against electrolyte overflow.

FusionModule2000 Smart Modular Data Center
Installation Guide
1 Safety Precautions
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5
When handling a battery, ensure that its electrodes are upward. Placing the battery upside
down or tilting the battery is prohibited.
Switch off the power supply during installation and maintenance.
Battery Short Circuit
Battery short circuits may cause personal injury. The high transient current generated by a
short circuit may release a surge of power and cause fire.
To avoid battery short circuits, do not replace batteries online.
Harmful Gas
Do not use unsealed lead-acid batteries. Place and secure lead-acid batteries horizontally to
prevent inflammation or device corrosion due to flammable gas emitted from batteries.
Lead-acid batteries emit flammable gas when used. Therefore, store these batteries in
well-ventilated areas, and take fire-prevention measures.
Battery Temperature
High temperatures may result in battery distortion, damage, and electrolyte overflow.
When the battery temperature is higher than 60°C, check the battery for electrolyte overflow.
If the electrolyte overflows, handle the leakage immediately.
Electrolyte Leakage
When the electrolyte leaks, absorb and neutralize the electrolyte immediately.
When moving or handling a battery whose electrolyte leaks, note that the leaked electrolyte
may hurt human bodies. If the electrolyte leaks, immediately use the following substances to
neutralize and absorb the leaked electrolyte:

FusionModule2000 Smart Modular Data Center
Installation Guide
1 Safety Precautions
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6
NaHCO3
Na2CO3
When using substances to neutralize and absorb electrolytes, strictly follow the guidelines
provided by the battery manufacturer.
If your body comes in contact with the leaked electrolyte, wash with clean water immediately
and seek medical advice if the situation is serious.
1.4 Mechanical Safety
This section describes the precautions be taken when moving sharp and heavy objects.
Drilling Holes
Do not drill holes on the rack without permission. Non-standard drilling may deteriorate
electromagnetic shielding performance and damage the internal cables, and metal scraps
generated during drilling may short-circuit a circuit board.
Before drilling holes on the rack, first remove the cables inside the rack.
To protect your eyes from metal shavings, wear a pair of goggles when drilling holes.
Before drilling holes, wear protective gloves.
When drilling holes, prevent metal shards from dropping into the cabinet.After drilling,
clean up metal shards immediately.
Moving Sharp Objects
Wear protective gloves when moving sharp objects.
Fan
When replacing a component, place the component, screws, and tools in a safe place.
Otherwise, if any of them fall into the operating fans, the fans may be damaged.
When replacing a component near fans, do not insert your fingers or boards into the
operating fans until the fans are switched off and stop running.
Moving Heavy Objects

FusionModule2000 Smart Modular Data Center
Installation Guide
1 Safety Precautions
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7
Be careful to prevent injury when moving heavy objects.
To prevent injury, when moving the chassis outwards, be aware of unfixed or heavy
objects on the chassis.
At least two persons are required to move the chassis. When lifting it, keep your back
straight and move smoothly to avoid injury.
Move or lift the chassis by holding its lower edge. Do not hold the handles on certain
modules such as power supply, fans, and boards because they cannot support the weight
of the device.
1.5 Others
This section describes the precautions to be taken when binding signal cables and laying out
power cables at a low temperature.
Binding Signal Cables
Signal cables must be bound separately from strong-current cables and high-voltage cables.
Routing Power Cables
When the temperature is low, violent strike or vibration may damage the cable sheathing. To
ensure safety, comply with the following requirements:
Cables can be laid or installed only when the temperature is higher than 0°C.
Before laying out power cables which have been stored in a temperature lower than 0°C,
move the power cables to an environment of the ambient temperature and store them at
the ambient temperature for at least 24 hours.
Handle cables with caution, especially at a low temperature. Do not drop the cables
directly from the vehicle.

FusionModule2000 Smart Modular Data Center
Installation Guide
2 Installation Preparations
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8
2 Installation Preparations
2.1 Precautions for Transportation and Placing
Precautions for Transportation
Only trained personnel are allowed to move the cabinet. Use a pallet truck to transport
the cabinet secured to a wooden support to the installation position. Insert the forks of
the pallet truck in the middle position to ensure balance.
Transport devices by railway, sea, or good road. No excessive tilt or jolt is allowed
during the transportation. The device can only be tilted for at most 15°during loading
and unloading, as shown in Figure 2-1.
To prevent the cabinet from falling over, secure it to a pallet truck using ropes before
moving it.
Move the cabinet with caution.Any bumping or falling may damage the device.
Unpack the device after moving it to the installation position.Avoid damaging the device
during unpacking. Take down the device from the pallet only immediately before
installation.
Figure 2-1 Cabinet tilt

FusionModule2000 Smart Modular Data Center
Installation Guide
2 Installation Preparations
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9
Precautions for Placing
Place cardboard boxes in sequence based on their numbers.
Figure 2-2 Arranging components
2.2 Unpacking and Acceptance
Context
Unpack and inspect all cabinets, mechanical parts, and components. Check that all the items
are intact and comply with the packing list on the presence of both the project supervisor and
customer.
Procedure
Step 1 Unpack the carton labeled Contain Packing List and take out the Packing List.
Step 2 Check all items against the Packing List.
Step 3 If an item is incorrect or missing, contact Huawei technical support.
Step 4 If any item is damaged, fill in the Cargo Replacement Application Form and report it.

FusionModule2000 Smart Modular Data Center
Installation Guide
2 Installation Preparations
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10
Step 5 Sign on the Packing List with the customer after verifying that all required items are
delivered.
Step 6 Store the items properly.
----End
Follow-up Procedure
Put the items to be installed immediately onto an ESD surface, such as a polyethylene
(PE) bag or an expandable polyethylene (EPE) foam.
Pack the items not to be installed immediately with their original packing materials. Put
them in a dry and cool environment without exposure to sunlight or sources of strong
electromagnetic radiation.
2.3 Installation Environment Check
Ensure that the installation environment meets the requirements before installation.
Table 2-1 Installation environment checklist
Check Item
Criteria
Check Result
Floor load bearing
capacity
Standard live load of the main
equipment room: 8–12 kN/m2(If the
battery cabinet is placed inside the
module, use the standard live load of
the main equipment room as a
reference.)
Suspended load of the main
equipment room: 1.2 kN/m2
Standard live load of the
uninterruptible power system (UPS)
room: 8–10 kN/m2
Standard live load of the battery
room: 16 kN/m2
Standard live load of the monitoring
center: 6 kN/m2
□ Passed □ Failed
Equipment room net
height
2000 mm high cabinets (without
bases): > 2800 mm
2200 mm high cabinets (without
bases): > 3000 mm
NOTICE
Equipment room net height (with bases) =
Equipment room net height (without bases)
+ Base height
□ Passed □ Failed
Device passage and
door height and
width
Height ≥ 2.2 m and width ≥ 1.2 m (If a
2200 mm high cabinet cannot go
through, tilt the cabinet.)
□ Passed □ Failed

FusionModule2000 Smart Modular Data Center
Installation Guide
2 Installation Preparations
Issue 02 (2018-03-31)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11
Check Item
Criteria
Check Result
Floor levelness
Allowed deviation: 2000±3 mm
□ Passed □ Failed
Elevator
Elevator load bearing capacity > 1.5
t
Elevator internal size: height > 2.4 m
or depth > 2.7 m
□ Passed □ Failed
Cable tray
Cable trays are preinstalled in the
equipment room for routing signal
cables and power cables.
□ Passed □ Failed
Power supply
380–415 V AC, 3 Ph, 50/60 Hz
□ Passed □ Failed
Fire extinguishing
Indoor gas-extinguishing system
□ Passed □ Failed
Floor drain
DN50 or larger, made of cast iron or
stainless steel
□ Passed □ Failed
Grounding
The equipment room grounding
system is a TN-S or TN-C-S system.
The equipment room ground grid has
a ground resistance no greater than
10 ohms. (If the ground resistance
exceeds 10 ohms, ensure that the
equivalent ground radius of the
ground grid exceeds 5 meters.)
Ground bars are deployed over the
cable tray or under the raised floor.
□ Passed □ Failed
Monitoring port
One LAN switch Ethernet port:
connects to the customer subnet to
monitor devices inside the module.
(Optional) Two fire control dry
contacts (access actuator and PDC
fire control terminal): connect to the
fire extinguishing system of the
equipment room for linkage.
(Optional) SIM card: supports 3G
(WCDMA) communication and is
compatible with 2G (GSM)
communication. If the collector
supports the SMS alarm function,
configure a SIM card.
NOTE
If there are multiple modules, configure a
collector for each module. For the collectors
that support the SMS alarm function,
configure a SIM card for each collector.
IP address: Each collector, camera,
and VCN requires an IP address,
respectively.
□ Passed □ Failed