Hubbell Chalmit ARRAN X ARXI/30/LE Manual

____________________________________________________________________________________________________________
PN KIL00921525 Form NO K1525 09/21 ERO6-073-21
1
IOM –ARRAN X LED
FLOODLIGHT (IND)
0.0 Specification
Type Of Protection
N/A
Standards
EN 60598-1,
Area Classification
Industrial, (Non- Hazardous)
Ambient
-50°C to +55ºC
Ingress Protection
IP66 to EN 60529
Photobiological safety of
Lamps and Lamp Systems
Risk Group 2 LED product to IEC 62471
Vision Advisory Claim
WARNING: Do not look at exposed led in operation especially with optical instruments. Eye
injury can result.
CE Mark
The CE marking of this product applies to "The Electrical Equipment (Safety) Regulations
2006", "The Electromagnetic Compatibility Regulations 2004", the “Waste Electrical and
Electronic Equipment Regulations 2006”. [This legislation is the equivalent in UK law of EU
directives 2014/35/EU, 2014/30/EU, 2012/19/EU respectively].
M Poutney Technical Manager
ARRAN X LED Floodlight Luminaire
Industrial
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
Important: Please read these instructions carefully before installing or maintaining this equipment.
Good electrical practices should be followed at all times and this data should be used as a guide only.

___________________________________________________________________________________________________
PN KIL00921525 Form NO K1525 09/21 ERO6-073-21
IOM –ARRAN X LED FLOODLIGHT (IND)
MEGOHM TEST - DUE TO THE SURGE PROTECTION PROVIDED IN THE LUMINAIRE TO PROTECT THE INTERNAL
ELECTRONICS AND LEDs, A CIRCUIT WITH THE LED FIXTURE MAY GIVE A FALSE MEGOHMMETER (MEGGAR)
READING. IF A MEGOHMETER TEST IS REQUIRED, THE LED FIXTURE SHOULD BE REMOVED FROM THE CIRCUIT.
The fitting’s driver is protected via thermal foldback sensor which reduces the light output of the fitting to prolong
the life of the driver in high ambient service conditions. When the driver reaches temperatures near the
manufacturer’s recommended limits, the foldback sensor will activate and slightly reduce the light output to
decrease the temperature of the fixture. Once the driver temperature reduces from this level, the fitting will
operate at normal levels.
1.0 Introduction –ARRAN X FLOODLIGHT
The ARRAN X LED Floodlight Luminaire operates from mains voltage.
Power Factor >0.95 Power is constant over voltage range.
Table 1 MODEL VARIATIONS
Ambient Range -50°C to +55°C
Tamb Storage -40°C to +50°C
Looping The looping current rating is 16A. 6mm² terminals are standard.
Fuse and MCB Ratings Current consumption, see table above. It is recommended that for selection of MCB's
users should consult the MCB manufacturer. MCB ratings can vary depending on the
manufacturer and type and the size of the installation, i.e. impedance of conductors,
however type ‘C’ breakers are usually suitable. The electronic control gear has an inrush
current of 34A for less than 50µs. These figures are worst case with low resistance
connections with short cables and low impedance supplies.
2.0 Storage
Luminaires should be stored in cool dry conditions preventing ingress of moisture and condensation.
3.0 Installation and Safety
3.1 General
There is no health hazards associated with this product whilst in normal use. However, care should be exercised during the
following operations. Installation should be carried out in accordance with IEE wiring regulations and any local authorised
practices. Any specific installation instructions must be referred to. In the UK the requirements of the 'Health and Safety at
Work Act' must be met. Handling and electrical work associated with this product to be in accordance with the 'Manual
Handling Operations Regulations' and 'Electricity at Work Regulations, 1989'. Your attention is drawn to the paragraphs
(i) 'Electrical Supplies',
(ii) 'Electrical Fault Finding and Replacement' and
(iii) 'Inspection and Maintenance'. The luminaires are Class 1 and should be effectively earthed.
The luminaires are quite heavy and suitable means of handling on installation must be provided.
CHALMIT MODEL
NUMBER
WATTS
Hz
VOLTS
AMPS
ARXI/30/LE
270
50/60
120-270AC/105-250DC
2.3-1.0/2.6-1.1
ARXI/20/LE
180
50/60
120-270AC/105-250DC
1.5-0.7/1.7-0.7
ARXI/14/LE
120
50/60
120-270AC/105-250DC
1.0-0.4/1.1-0.5
ARXI/10/LE
90
50/60
120-270AC/105-250DC
0.8-0.3/0.9-0.4
ARXI/07/LE
60
50/60
120-270AC/105-250DC
0.5-0.2/0.6-0.2
ARXI/07/LE/EM
120
50/60
120-270
1.0-0.4
ARXI/14/LE/EM
60
50/60
120-270
0.5-0.2

___________________________________________________________________________________________________
PN KIL00921525 Form NO K1525 09/21 ERO6-073-21
IOM –ARRAN X LED FLOODLIGHT (IND)
Guard and Reflector can be supplied with or fitted retrospectively, the guard is to protect glass if there is a higher than normal
risk of mechanical damage. The guard and reflector can be fitted together.

___________________________________________________________________________________________________
PN KIL00921525 Form NO K1525 09/21 ERO6-073-21
IOM –ARRAN X LED FLOODLIGHT (IND)
3.2 Tools
M8 hex socket
4mm flat blade screwdriver
Suitable spanners for installing cable glands
Pliers, knife, wire strippers/cutters
3.3 Electrical Supplies
A maximum voltage variation of +6%/-6% on the nominal is expected.
3.4 Light Source
The luminaire is fitted with LEDS that can last 80,000 hours depending on ambient temperatures. Therefore depending on
the functionality of the fitting replacement of LED’s will be rare /unnecessary. If the LED assembly needs replaced refer to 4.2
LED Replacement.
3.5 Mounting
Luminaires should be installed where access for maintenance is practical and in accordance with any lighting design
information provided for the installation. This will usually consist of aiming points and aiming angles. Mounting ARRAN X
arrangements should be secured with lock washers or self-locking nuts and bolts.
3.5.1 AIMING DESIGNATIONS
In environments with high dust, the dust will cover the lens and increase the temperature of the fixture. In a high dust
environment use the aiming diagram shown below as directed on the nameplate. The angle shown below will keep dust
from accumulating on the lens.
Figure A Figure B
3.6 Cabling and Cable Glands
3.6.1 Cable
The maximum conductor size is 6mm². Open the fixture by loosening the swing bolts. Using the terminal blocks supplied,
run supply wire to fixture through applicable hub. Make watertight joint using sealing fittings at appropriate hole.
The holes through the cast metal in the driver compartment are for an M20 cable gland.
The terminal block shown is with battery back up. Non
back up fixtures will not have the “L2” terminal. Mains
wiring should be brought into the corresponding marked
terminal. Looping wiring can be accomplished by using
the adjacent connection port. A small screwdriver can be
inserted in the slot near the connection port to ease the
force required to insert the wire.The external ground is
located next to the gland/hub opening where the mains
wires exit the fixture.
Reattach the swing bolts. Torque the cover bolts until the cover touches the housing. Approximately 3 N-m. Re-
energized the circuit to verify the fixture is operating properly
IMPORTANT: To turn the fixture completely off, an un-switched AC power source of 120VAC to 277VAC is required for the
Line Maintained (yellow) and neutral (white) leads. A locally switched line must be attached to the Line Switched (black)
terminal. If the Line Switched terminal is attached to continuous power, the fixture will go into battery backup mode if the
power is turned off.

___________________________________________________________________________________________________
PN KIL00921525 Form NO K1525 09/21 ERO6-073-21
IOM –ARRAN X LED FLOODLIGHT (IND)
IMPORTANT: Fixtures are shipped with a jumper between the Line Maintained and Line Switched terminals. Remove the
wire link (jumper) and attach the Line Switched terminal to a local switched source when local switching is required. The
battery must be charged for at least 12 hours prior to testing. The battery switch must be turned to the “ON” position for the
fixture to operate correctly. The fixture will not light up in battery backup mode until AC power is supplied once while the
battery switch is in the “ON” position. Thereafter, the fixture will operate in battery backup mode when the AC power is off.
SELF-DIAGNOSTIC INSTRUCTIONS/OPERATION: The self-diagnostic feature is set from the factory. The emergency LED
driver will conduct a self-check for thirty (30) minutes every thirty (30) days; and ninety (90) minutes or one hundred eighty
(180) minutes self-check every 12 months. After every self-check the LED indicator light will indicate a status signal.
3.6.2 Cable Glands
The installer and user must take responsibility for the selection of cables, cable glands and seals. Cable glands and sealing
plugs when installed must reliably maintain the IP rating of the enclosure IP66. Sealing plugs are provided and a tool must be
used for their removal. Where brass cable glands are used in a corrosive environment, cadmium or nickel plating should be
used. Two tapped cable entries are provided, one with a plug and seal suitable for permanent use, the other has a travelling
plug. M20 entries are standard, other sizes are available on request up to M25.
4.0 Inspection and Maintenance
Visual inspection should be carried out at a minimum of 12 monthly intervals and more frequently if conditions are severe.
Maximum Insulation Resistance Test 500V dc.
1 Check if any LED’s have failed (not lit).
2 The LEDs are mounted on boards, if there is 3 or more LED's not working on one board the light output will have
dropped to a level where the LED board may need replaced. Refer to 4.2 LED Replacement.
3 Check for mechanical damage/corrosion.
4 Check for loose connections including earthing.
5 Check for undue accumulations of dust or dirt.
6 Verification of tightness of fixing, glands, blanking plugs etc.
7 Check for unauthorised modifications.
8 Check condition of enclosure gaskets and fastenings.
9 Check for any accumulation of moisture.
10 Clean the lamp glass.
11 Check that mountings are secure.
12 If there is suspicion that the luminaire has suffered mechanical damage, a stringent workshop check should be made.

___________________________________________________________________________________________________
PN KIL00921525 Form NO K1525 09/21 ERO6-073-21
IOM –ARRAN X LED FLOODLIGHT (IND)
Important: Where spares are needed, these must be replaced with manufacturer parts. No modifications should be made
without the knowledge and approval of the manufacturer.
4.1 Electrical Fault Finding and Replacement
Any fault finding must be done by a competent electrician with the luminaire isolated and if carried out with the luminaire in
place, under a permit to work. Fault finding is by substitution with known good components.
4.2 LED Replacement.
The need and frequency of replacing LED’s be dependent on the functionality of the fitting. If it is continually running at high
ambient temperatures it will affect the frequency of LED replacement. If it is necessary to replace the LED’s, the LED’s are
mounted on boards that can be replaced individually. (The boards with LED's supplied by Chalmit ). Remove cover
assembly.
Removal of LED assembly is as follows:
1. Unscrew the screws that secure the board to the casting.
2. Carefully lift the plate and disconnect push in connector.
Replacement of LED assembly is the reverse of the removal.
Replace Front cover and fully tighten all bolts.
4.3 Battery Replacement
1. Make sure that the circuit is de-energized
2. Remove the housing cover.
3. Remove wires from lever nuts as necessary. To remove a wire from a lever nut, fully push up the lever and remove the
conductor.
4. Remove the two screws that hold the driver to the housing.
5. Remove the two screws that hold the battery compartment cover to the driver.
6. Disconnect the connector and replace the new battery (part number VM-BATT).
7. Reassemble
New fixtures with batteries can be stored for 2 years in a -20°C to 30°C ambient without a need of recharge. A fully
discharged unit should not be stored more than 6 months without being recharged. There is low voltage disconnect of the
battery to the emergency drivers, however as the batteries still have self-discharge they should be recharged within 6 months
to prevent the cells from permanent capacity loss. For long term storage, turn the battery switch to the “off” position to
prevent the cells from permanent capacity loss.
5.0 Disposal of Material
The unit is mostly made from incombustible materials. The control gear contains electronic components and synthetic resin.
All these may give off noxious fumes if incinerated. Care must be taken to render these fumes harmless and avoid
inhalation. Any local regulations concerning disposal must be complied with. Any disposal must satisfy the requirements of
the WEEE directive [2012/19/EU] and therefore must not be treated as commercial waste.
To comply with the Waste Electrical and Electronic Equipment directive 2012/19/EU the
apparatus cannot be classified as commercial waste and as such must be disposed of or
recycled in such a manner as to reduce the environmental impact.

___________________________________________________________________________________________________
PN KIL00921525 Form NO K1525 09/21 ERO6-073-21
IOM –ARRAN X LED FLOODLIGHT (IND)
Directions for Installation of Accessories
WARNING: Ensure the supply circuit is off before starting installation.
Conditions for Safe Use:
1. To prevent ignition of hazardous atmospheres, disconnect ballast/fixture from supply circuit before
opening. keep tightly closed when in operation.
2. Do not open, maintain or service in an area where an explosive atmosphere may be present.
3. When Polycarbonate lens is in use, clean lens with damp cloth to avoid static discharge.
4. The luminaire shall only be installed where there is a low risk of mechanical damage.
Wire Guard Installation
Place wire guard over lens area, placing loops over holes
behind LED Housing. Attach guard to housing using two
screws provided through bosses in housing.
Both guard and reflector can be used on a fixture
simultaneously.
Dark Skies Reflector Installation
Place reflector over LED Housing. Hook tab on bottom of
reflector over boss going from Driver Housing to LED
Housing. Attach reflector to LED Housing using two
screws provided through bosses in LED Housing.

___________________________________________________________________________________________________
PN KIL00921525 Form NO K1525 09/21 ERO6-073-21
IOM –ARRAN X LED FLOODLIGHT (IND)
EU-Declaration of conformity
UE-Déclaration de conformité
EU-Konformitätserklärung
Manufacturer
Chalmit
Address
388 Hillington Road, Glasgow. G52 4BL Scotland UK
Product
ARRAN X LED Floodlight Industrial
Catalogue
ARXI/30L/LE/** see Table 1
Area Classification
Industrial, (Non- Hazardous)
Ingress Protection
IP66
Ambient
-50°C to +55°C
Terms of the directive:
Standard & Date Certified to
Standards Date Declared to
2014/30/EU
Electromagnetic compatibility
EN 55015 : 2013
2014/30/UE
Compatibilité électromagnétique
EN 61547 : 2009
2014/30/EU
Elektromagnetische Verträglichkeit
EN 61000-3-2 : 2014
2014/35/EU
Low voltage equipment
EN 60598-1 : 2015
2014/35/UE
Équipements électriques à bas voltage
EN 60598-2-5 : 2015
2014/35/EU
Niederspannungsgeräte / -systeme
EN 60529 : 1992
2012/19/EU
Waste of electrical and electronic equipment
2012/19/UE
Déchets d'équipements électriques et électroniques
2012/19/EU
Entsorgung der elektrischen und elektronischen Geräte
/ Systeme
2011/65/EU
RoHS II Directive
On behalf of the Chalmit, I declare that, on the date the equipment accompanied by this declaration is placed on the market, the equipment
conforms to all technical and regulatory requirements of the above listed directives.
En tant que représentant du fabricant Chalmit, je déclare qu'à la date où les équipements accompagnant cette déclaration sont mis sur le
marché, ceux-ci sont conformes à toutes les dispositions réglementaires et techniques des directives énumérées ci-dessus.
Hiermit bestätige ich, im Namen von Chalmit, dass am Tag der Lieferung des Produkts/der Produkte zusammen mit dieser Erklärung das
Gerät/die Geräte alle technischen und regulativen Anforderungen der oben aufgeführten Direktiven erfüllt.
Name and Date
Mark Poutney
02/09/2021
Technical Manager
Nom et Date
Directeur technique
Name und Datum
Technischer Leiter
Quality Management System Acreditation:
ISO 9001
Système de Management Qualité Accréditation:
Qualitätsmanagementsystem Akkreditierung:
Environmental Management System.
ISO 14001
Système de gestion de l'environnement.
by/par/durch
Umwelt kontroll system.
Loyd's Register
Certificate No./Certificat N°/Zertifikat Nr.
LRQ 4005876