HUCK Seiltechnik 4591-81-BM User manual

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
1
AAssembly Instructions
Slowworm, Art.-No. 4591-81-BM
Attention, Only use the instructions included in the scope of delivery for the as-
sembly, installation and maintenance of the respective equipment!
Operator: _________________________________________________________
Location: _________________________________________________________

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
2
Revisionshistorie
Revision 0 –2021-11-12
Erste freigegebene Version: FH
Wartungsanleitung
Alle Rechte vorbehalten
© Copyright 2021 Huck Seiltechnik GmbH

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
3
Please note the explanations and abbreviations and notes.
For any queries please contact the manufacturer
Contents
AAssembly Instructions Slowworm, Art.-No. 4591-81-BM ...........................................1
1Introduction Assembling..............................................................................................4
2Datasheet: Slowworm Art.-Nr.4591-81-BM..................................................................6
3Delivery contents (parts list with part numbers) ........................................................7
4Explanation of abbreviations and signs....................................................................10
5Assembly instructions................................................................................................12
6Post installation checks .............................................................................................17
BMaintenance instructions Slowworm, Art.-Nr. 4591-81-BM......................................19
7Introduction Maintenance...........................................................................................21
8General maintenance information .............................................................................22
9Maintenance timetable................................................................................................24
10 Regular maintenance..................................................................................................25
11 Monthly maintenance .................................................................................................26
12 Quarterly maintenance...............................................................................................26
13 Half yearly maintenance.............................................................................................27
14 Annual maintenance...................................................................................................27
15 Maintenance printout..................................................................................................29
16 Hand over document ..................................................................................................31
List of Tables
Table 3-1: Delivery contents, in words...................................................................................7
Table 3-2: Delivery contents, in symbols................................................................................9

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
4
1 Introduction Assembling
1.1 General information
This equipment should be installed, inspected, maintained and operated
in accordance with EN1176-7 guidelines.
Before installation work commences, please check that you have all of
the equipment and fixation components in the parts list provided (see
Tables 3-1 and 3-2).
Please consider that the installation has to be carried out only on even
terrain (max.slope up to 3%).
Any spare parts that may be required can be obtained directly from your
supplier or from Fa. Huck Seiltechnik GmbH
Adress: Huck Seiltechnik GmbH
Dillerberg 3
D-35614 Aßlar/Berghausen
Tel. [phone]
Fax [phone]
Please do not hesitate to call your supplier if you have any problems during in-
stallation or with any other questions. You can reach us at the following Tel.
[phone].
Following installation, complete assembly instructions, maintenance in-
structions and a maintenance record must be sent to the operator who
must confirm receipt in writing. See the last page of this document.
All nuts and bolts are hot-dip galvanised or stainless steel.
One of the characteristics of stainless steel is that uncontrolled cold
welding may occur when the nuts are tightened. To prevent this, it is
necessary to spray the nuts and bolts with Teflon spray or another simi-
lar lubricant.

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
5
Drawings / Views
All optical drawings are showing only the measurements/dimensions and are
no mandatory technical views of the complete item.
We reserve the right to change technical details of our articles which are serv-
ing for the further development of our articles and are reasonable for the cus-
tomer.
Measurement tolerances
Because of the properties and characteristics of the components, minor meas-
urement tolerances compared to the indication on the sketches are possible.
This concerns all shown measurements except the foundation
measurements resp. measurements below upper edge ground level/play
area.

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
6
2 Datasheet: Slowworm
Art.-Nr.4591-81-BM
Space requirement: 4.25 m x 4.12 m
Safety zone: 7.10 x 7.05 m
Height of equipment: 0.60 m
Height of fall: 0.60 m
Fall protection area: 32.2 m²
1. Required safety surface
Name and size of the largest part of the device:
PP-Rope pos. 01 / 900mm x 11900mm long
2. Name and weight of the heaviest part of the equipment:
PP-Rope pos. 01 / ca. 283 kg
3. Intended age group: from 3 years
Attention! Device for embedding + for setting in concrete:
Excavation size:
Lifting 800 mm deep, size see drawing
4. assembly time approx. 1.5 hours after completion of the excavation of the respective ex-
cavation sizes
Needed persons: 3
5. Possibly required spare parts can be obtained directly from your supplier or from the com-
pany Huck Seiltechnik GmbH
Adress: Huck Seiltechnik GmbH
Dillerberg 3
D-35614 Aßlar/Berghausen
Tel. [phone]
Fax.[phone]
6. We hereby confirm that this play equipment has been tested
and certified in accordance with the play equipment standard EN 1176-1.
Surface material
Description / mm
Minimum thickness
of layer / mm
Maximum height of
fall / mm
Lawn / topsoil
-
-
≤ 1000*
Bark mulch
20 –80 Particle size
300
≤ 2000
400
≤ 3000
Wood chips
5 –30 Particle size
300
≤ 2000
400
≤ 3000
Sand
0,25 –2 Grain size
300
≤ 2000
400
≤ 3000
Gravel
0,25 –8 Grain size
300
≤ 2000
400
≤ 3000
Other floor materi-
als
As per HIC audited
Critical drop height
as tested
Sand and gravel must be well rounded to remove most of the silty or clayey particles. Washed sand or gravel is considered to be
alluvial and free from silty or clayey particles. With gravel this is generally described as "pearl gravel". Degree of non-uniformity
D60/D10 < 3.0. The grain size can be determined by using a sieve method.

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
7
3 Required safety surface:
Delivery contents (parts list with part numbers)
3.1. In words
Table 3-1: Delivery contents, in words
Pos.
Quantity
Element /
Description
Size
O.K.
Mis-
sing
1.0
1x
PP-Rope,square
Ø 160mm ca.L=4,0m
1.1
11x
Hexagon head screw DIN
933 full thread vz + U-Sch.
DIN 9021 Vz.
M16 x 30 + U-Sch.
1.2
22x
Hexagon head screw gal-
vaized DIN 931 partial
thread
M10 x 75 mm
1.3
22x
Galvanized cap nut DIN
986 with stop function
M10
2.0
4x
Steelpost galv.
Ø 51 x 2,9mm L=1,05m
2.1
3x
Steelpost galv
Ø 51 x 2,9mm L=1,18m
2.2
4x
Steelpost galv
Ø 51 x 2,9mm L=0,89m
3.0
3x
Anchor flat zinc plated
500 x 500 mm

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
8
3.2. In symbols
Pos.
Quantity
Symbol
1.0
1x
L= ca.11.90 m
1.1
11x
M16 x 30mm + M16 / Ø50mm
1.2
22x
M10 x 75mm
1.3
22x
M10
2.0
4x
Ø 51mm x 2,9mm L= 1,05m
2.1
3x
Ø 51mm x 2,9mm L= 1,18m

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
9
Pos.
Quantity
Symbol
2.2
4x
Ø 51 mm x 2,90 mm L = 0,89 m
3.0
3x
500 x 500mm

HUCK Seiltechnik GmbH • Dillerberg 3 • D-35614 Asslar-Berghausen
[e-mail] - www.huck.net
\\CAD1\Standard\4591-81-BM\Montageanleitung\4591_81_BM_Blindschleiche_ST_E_L_01_GBR.doc
10
Explanation of abbreviations and signs
See drawings!
Abbreviations
Ka.O
Edge points upwards
Sp-Gr.
Put the play equipment on the tubes
Aus.v.v.
Thoroughly recompact the excavated material
G
Seepage layer 10 cm
PS
Security area
Wa.A.b
Observe the maintenance instructions!!!