HUCK Seiltechnik Swing Bed 4591-50-9 User manual

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
1
AAssembly instructions
“Swing Bed” Easy - Swing
Art.-Nr. 4591-50-9
Operator: _________________________________
Location: _________________________________

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
2
Revision history
Revision 0 –2007- 08-21
First released version
Assembly instruction SP
Revision 5 –2020-05-18 PM
Geräteraufstellmaße komplett geändert nach neuer Norm EN 1176 2017
All rights reserved
© Copyright 2020 Huck Seiltechnik GmbH

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
3
Table of content
AAssembly instructions “Swing Bed” Easy - Swing Art.-Nr. 4591-50-9......................1
1Introduction installation ...............................................................................................4
2Data sheet “Swing Bed“ Easy- Swing Art.-Nr. 4591-50-9.....................................6
3Scope of supply, parts list with part numbers............................................................8
4Abbreviations.............................................................................................................. 11
5Assembly instruction.................................................................................................. 12
6Examination after installation.................................................................................... 20
BMaintenance instructions “Swing Bed” Easy - Swing part no. 4591-50- 9.............. 21
7Introduction maintenance .......................................................................................... 23
8General maintenance information ............................................................................. 24
9Maintenance timetable................................................................................................ 26
10 Regular maintenance.................................................................................................. 27
11 Monthly maintenance ................................................................................................. 28
12 Quarterly maintenance............................................................................................... 28
13 Half-yearly maintenance............................................................................................. 28
14 Annual maintenance................................................................................................... 29
15 Maintenance printout.................................................................................................. 31
16 Hand-over document.................................................................................................. 33
List of Tables
Table 3-1: Scope of supply, parts list with part numbers........................................................ 8
Table 3-2: Scope of supply, parts list with part numbers........................................................ 9

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
4
1 Introduction installation
1.1 General information
This equipment should be installed, inspected, maintained and operated in
accordance with EN1176-7 guidelines.
Before installation work commences, please check that you have all of
the equipment and fixation components in the parts list provided (see
Tables 3-1 and 3-2).
Please consider that the installation has to be carried out only on even
terrain (max.slope up to 3%).
Any spare parts that may be required can be obtained directly from your
supplier or from Fa. Huck Seiltechnik GmbH
Adress: Huck Seiltechnik GmbH
Dillerberg 3
D-35614 Aßlar/Berghausen
Tel. [phone]
Fax [phone]
Please do not hesitate to call your supplier if you have any problems during in-
stallation or with any other questions. You can reach us at the following Tel.
[phone].
Following installation, complete assembly instructions, maintenance
instructions and a maintenance record must be sent to the operator
who must confirm receipt in writing. See the last page of this docu-
ment.
All nuts and bolts are hot-dip galvanised or stainless steel.
One of the characteristics of stainless steel is that uncontrolled cold
welding may occur when the nuts are tightened. To prevent this, it is
necessary to spray the nuts and bolts with Teflon spray or another
similar lubricant.

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
5
Drawings / views
All optical illustrations simply demonstrate the proporti-
ons/dimensions to be followed, but are not binding, technical
equipment images.
Technical modifications supporting the advancement of our
articles are subject to change.
Measurement tolerance / dimensions
Due to the quality and characteristics of equipment parts, mi-
nor dimensional tolerances over drawings data are possible.
This regards all visible dimensions, except for foundation
dimensions respectively dimensions below OK ground
surface/play surface.

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
6
2 Data sheet “Swing Bed“ Easy- Swing
Art.-Nr. 4591-50-9
1. Space requirement: 2650 x 2600 mm
safety zone:: 7050 x 2250 mm
Height of equipment: 2450 mm
Height of Fall: 1250 mm
Fall protection area: 15,86 m²
2. Required safety surface:
Surface material
Description / mm
Minimum thick-
ness of layer /
mm
Maximum height
of fall / mm
Lawn / topsoil
-
-
≤ 1000*
Bark mulch
20 –80 Particle size
300
≤ 2000
400
≤ 3000
Wood chips
5 –30 Particle size
300
≤ 2000
400
≤ 3000
Sand
0,25 –2 Grain size
300
≤ 2000
400
≤ 3000
Gravel
0,25 –8 Grain size
300
≤ 2000
400
≤ 3000
Other floor
materials
As per HIC audited
Critical drop
height as tested
Sand and gravel must be well rounded to remove most of the silty or clayey particles. Washed sand or gravel is considered
to be alluvial and free from silty or clayey particles. With gravel this is generally described as "pearl gravel". Degree of non-
uniformity D60/D10 < 3.0. The grain size can be determined by using a sieve method.
*In Germany, lawn is a sufficient ground surface in the safety zone for
heights of up to 1500 mm.
3. Name and size of the largest part of the device:
Steel post Pos. 01 / Ø102 mm –3400 mm length
4. Name and weight of the heaviest part of the equipment:
Steel post Pos. 01 / ca. 24,5 kg
5. Intended age group: 2 years and up
6. Attention! Device for embedding + for setting in concrete:
Foundation
Concrete: C25/30
Concrete requirements: 1,41 m³
Foundation size: 2600 x 900 x 600 mm
Quantity: 2x
Concrete upper edge: 400 mm below upper edge (O.K.) of play level
Excavation size:
1x 2600 x 900 x 1100 mm (inclusive 100 mm drainage layer)

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
7
7. Required accessories: Small excavator, ladder of about 2m length baromet-
ric level, water balance, various drills (Ø11, Ø13, Ø17), various wrenches resp.
Allen wrenches, compactor (Frosch), screw driver.
Upper edges of concrete are rounded! Foundation sizes apply for regular
soil classification 4-5 (grown surface).
Soil classification 4: Light up to medium plasticity, interlaced, with little
sediment (proportion < 30 % larger than 63 mm grain size in diameter)
Soil classification 5: Grounds of soil classification 3 and 4 with more sed-
iment (proportion > 30 % larger than 63 mm grain size in diameter)
For safety reasons, foundations of sandy, soft grounds should be lay-
ered with a larger surface of at least 50%.
8. Assembly time approx. 45 minutes after the steel posts
have been set in concrete
Needed persons: 3
9. Possibly required spare parts can be obtained directly from your supplier or
from the company Huck Seiltechnik GmbH
Adress: Huck Seiltechnik GmbH
Dillerberg 3
D-35614 Aßlar/Berghausen
Tel. [phone]
Fax.[phone]
10. We hereby confirm that this play equipment has been tested and certified
according to the new play equipment standard EN 1176.

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
8
3 Scope of supply, parts list with part numbers
3.1 in letters
Table 3-1: Scope of supply, parts list with part numbers
Pos.
Quantity
Element /
description
Size
O.K.
Missing
01
4
Steel posts
Ø102 mm
lg. 3400 mm
02
4
cover caps
Ø102 mm
03
4
pipe clamps
Ø102 mm
04
4
pipe clamps with
threaded bolt + nuts
Ø102 mm
M10 x 150 mm
05
1
Play equipment with 4 sus-
pension ropes (chains + safety
chains. (pre-assembled)
900 x 1350 mm
06
4
Screws
M10 x 35 mm
07
12
self-tapping screw
5,5 x 25 mm
08
1
Loctite
3 ml
09
4
Pavement slab
(on-site customer)
Ca. 300 x 300 mm

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
9
3.2 in symbols
Table 3-2: Scope of supply, parts list with part numbers
Pos.
Quantity
Symbol
01
4
Ø102 mm / lg. 3400 mm
02
4
Ø102 mm
03
4
Ø102 mm
04
4
Ø102 mm / M10 x 150 mm
05
1
900 x 1350 mm

HUCK Seiltechnik GmbH - Dillerberg 3 –35614 Asslar-Berghausen
[email protected] - www.huck.net
\\CAD1\Standard\4591-50-9\Montageanleitung\Easy_Swing_Schaukelbett_4591_50_9_ST_B_L_1_GBR.doc
10
06
4
M10 x 35 mm
07
12
5,5 x 25 mm
08
1
3 ml
09
4
Ca. 300 x 300 mm (on-site customer)