Hughes DW 3000 One-Way User manual

Satellite Dish Installation
Guide
Model: DW 3000 One-Way
1031361-0202
Revision B
November 19, 2001

Copyright © 2000-2001 Hughes Network Systems, a Hughes Electronics Corporation company
All rights reserved. This publication and its contents are proprietary to Hughes Network Systems, a
Hughes Electronics Corporation company. No part of this publication may be reproduced in any form
or by any means without the written permission of Hughes Network Systems, 11717 Exploration
Lane, Germantown, Maryland 20876.
Hughes Network Systems has made every effort to ensure the correctness and completeness of the
material in this document. Hughes Network Systems shall not be liable for errors contained herein.
The information in this document is subject to change without notice. Hughes Network Systems
makes no warranty of any kind with regard to this material, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose.
Trademarks
All trademarks, marks, names, or product names referenced in this publication are the property of
their respective owners, and Hughes Network Systems neither endorses nor otherwise sponsors
any such products or services referred to herein.

iii
Table of Contents
Satellite Dish Kit Components . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Conventions Used in this Guide . . . . . . . . . . . . . . . . . . . . . . . . . 2
A Word to the Do-It-Yourselfer . . . . . . . . . . . . . . . . . . . . . . . . . 3
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing Software and Locating the Satellite . . . . . . . . . . . . . . 6
Choosing Where to Install the Satellite Dish . . . . . . . . . . . . . . . 7
Cable Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Selecting a Mounting Option . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing The Mount on a Wooden Deck Post . . . . . . . . . . . . . 12
Installing the Mount on a Wood Framed Roof . . . . . . . . . . . . . 15
Installing the Mount on Concrete or Concrete Masonry Walls. 20
Installing the Mount Onto a Metal Pole . . . . . . . . . . . . . . . . . . 22
Installing the Cap Onto the Satellite Dish. . . . . . . . . . . . . . . . . 23
Installing the LNB/Waveguide . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting the Feed Arm to the Satellite Dish. . . . . . . . . . . . . 26
Installing the Satellite Dish/Cap Assembly onto the Mast . . . . 27
Installing and Routing Interior Cable . . . . . . . . . . . . . . . . . . . 28
Installing Exterior Cables and Connecting to Ground Block . 29
Connecting the Coaxial Cable to the LNB . . . . . . . . . . . . . . . . 30
Overview of Grounding the Satellite System . . . . . . . . . . . . . . 31
Grounding the Mast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Grounding the Metal Pole Mount . . . . . . . . . . . . . . . . . . . . . . . 35
Attaching the Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Pointing the Satellite Dish. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

iv

1
SATELLITE DISH KIT COMPONENTS
YOUR SATELLITE DISH KIT SHOULD INCLUDE THE FOLLOWING ITEMS:
PARTS LIST
Your kit also contains assorted hardware. Depending on how you install and ground your system, you may have some
hardware left over when you are done. You will have to supply other items. Go to page 4 to view a table that lists what you will
need to supply.
• M4 Allen screws, Qty: 4
• Red O-ring, Qty: 1 • 5/16-inch Lock washer, Qty: 1 • 1/4-20 Hex-Head Nut, Qty: 1
• Galvanized washers, 3/8-inch Qty: 6
• Allen wrench, 3mm, Qty: 1 • 5/16-18 x 2-inch Hex screw, Qty: 1 • 5/16-18 Wedge nut, Qty: 1
• Lag screws, 1/4-inch x 4-inch, Qty: 4
• Lag screws, 3/8-inch x 2-inch, Qty: 4 • 5/16-inch Flat washer, Qty: 5 • Galvanized washers, 1/4-inch, Qty: 4
• Lag screws, 3/8-inch x 4-inch, Qty: 6
• 5/16-inch Nylock nuts, Qty: 4 • 1/4-20 x 1/2-inch Hex-Head Bolt, Qty: 1 • 1/4-inch Lock washer (star washer for
grounding), Qty: 1
Satellite Dish (rear view) Mast and Base
Plate Feed Arm
Azimuth/Elevation Cap Shroud LNB/Waveguide Assembly
Brace kit
Also included are the indoor
items that are necessary to
connect the satellite dish
and your computer. See the
installation guide that comes
with the software and indoor
components (packaged sep-
arately in the antenna box)
for a complete list.

2
CONVENTIONS USED IN THIS GUIDE
The following conventions are used throughout this guide to help you become familiar with possible safety and equipment hazards.
Note: A note presents additional information.
This safety alert symbol is used to alert you to hazards or
hazardous situations that can result in personal injury. A
signal word,
DANGER, WARNING
,or
CAUTION
, is used
with the alert symbol to indicate the likelihood and
potential severity of injury.
DANGER
Indicates an imminent hazard or unsafe practice which, if
not avoided, will result in death or severe personal injury.
WARNING
Indicates a hazard or unsafe practice which, if not
avoided, could result in death or severe personal injury.
CAUTION
Indicates a hazard or unsafe practice which, if not
avoided, might result in moderate or minor personal injury.
CAUTION
When used without the alert symbol, indicates a hazard or
unsafe practice that might result in property damage.

3
A WORD TO THE DO-IT-YOURSELFER
We recommend you ask a professional satellite installer to mount your satellite dish and run your cables, but we recognize that
some people will elect to do their own installation. If you are one of these people, or if you are undecided about whether or not to
perform your own installation, please consider the following.
• Mounting the satellite dish to a concrete or masonry foundation, exposed deck timber, or metal pole are the best options for the
homeowner because you can see that the fasteners are properly installed.
• Mounting the satellite dish to the house roof is a desirable mounting method only if you are positive that you can drill the holes for
lag screws within 1/16-inch of the center of the rafters or trusses. This requires special tools and expertise. If you must mount to a
roof, pick a location where the roof is unfinished and accessible from the inside so that you can reinforce it if necessary and assure
yourself that the fasteners penetrated the rafters or trusses without splintering them.
• Do not depend on consumer quality stud finders to locate rafters underneath asphalt shingles because they may give false positive
readings or miss rafters entirely.
• Given a choice, it is always best not to penetrate a roof.
• If a lag screw misses the rafter or truss but is securely fastened in the sheathing, the satellite dish could pull the lag screws out of
the sheathing or peel the sheathing away from the rafter or truss during high wind loads.
• If you plan to upgrade to a Two-Way System, which requires that the satellite dish be installed by a professional installer, we sug-
gest you review the copy of its satellite dish installation manual, HNS part number 1031362-0201, on your software installation
CD. The manual can help you understand the Two-Way System installation requirements.
• When cabling, if there is even a remote possibility that you will upgrade to either a DIRECTV®system or a Two-Way System, run
extra cables to save yourself future effort.
• If you plan to or think you may upgrade to a Two-Way System, be sure to install your base plate so that its center is 5 feet above
ground.
• Best grounding results are achieved with quad shielded RG6 coaxial cable with a shield resistance of less than 0.6 ohms per 100
feet.
• If you install the satellite dish yourself, you must supply a number of items. See the following table.

4
Type of installation Parts you must supply Tools you must supply
ALL INSTALLATIONS
• Coaxial cable (see “Cable specifications” on
page 9)
• Weatherproof 360° cable connectors
• Cable ties
• Insulated U-shaped tacks
• F-type ground block and screws
• 1/4-inch washer (for grounding if not using RG-6
quad shielded cable)
• #6 washer (to help with drilling)
• Silicone sealant
• 8AWG aluminum and/or 14AWG copper ground
wire, as required for installation or grounding
scheme
• If not using RG-6 quad shield coaxial cable, one
split bolt with nut for connections at the ground
block
•Compass
• Angle finder or protractor
• Carpenter’s level
• Pencil or chalk
• Ladder or stepladder
• Electric drill
• Ruler and tape measure
• Adjustable wrench (socket preferred)
• Torque wrench (up to 18 ft.-lbs.)
• Open-end or socket wrenches: 3/16, 1/2, 5/16,
7/16, 9/16-inch
• Needle-nose pliers
• Lineman pliers
•String
• #2 Phillips or similar screwdriver
• Flat-blade screwdriver
• Hammer
• Permanent marker
Wood post
All parts supplied • Drill bits: 3/8, 1/4, and 1/8-inch
Wood frame roof
• If you decide to use 5/16-inch x 4-inch lag screws
for this installation,youmust provide them and the
5/16-inch galvanized washers
• Drill bits: 3/8, 1/4, 1/8, and 5/32-inch
Concrete masonry or
concrete wall
• 3/8-inch x 3-inch Hilti sleeve anchor, Qty: 6
• If also installing optional brace kit, 1/4-inch x 2-1/4-
inch Hilti sleeve anchor, Qty: 4
• Hammer drill
• Masonry drill bits: 3/8-inch
Metal pole
• Metal pole, 2-3/8-inch diameter, 9 feet long,
schedule 40 galvanized
• 1-inch x 2-3/8-inch ground clamp for metal pole
• 40-lb. bags quick-setting concrete, Qty: 3
• If not using RG-6 quad-shielded cable, one 5/8-
inch by 10-foot ground rod and ground rod clamp
• Hole-digging tools
• Wheelbarrow or concrete mixing box
•Hacksaw

5
INTRODUCTION
This Satellite Dish Installation Guide Model: DW 3000 One-
Way provides information required to assemble your satellite
dish and establish contact with the satellite.
OTHER USEFUL GUIDES
The installation guide included with the software and indoor
equipment gives an overview of the entire installation process,
including the modem and software installation.
WHAT IS INCLUDED IN THE SATELLITE BROADBAND SYS-
TEM
The satellite broadband system consists of several major com-
ponents:
• The receive modem
• The satellite dish assembly that is installed outside
• Cables for connecting the receive modem and your computer
•Software
• This guide and the installation guide included with the soft-
ware and indoor equipment
This guide is intended for an installer experienced in perform-
ing the various installation tasks. Depending on how you will
install the satellite dish, you may be required to:
• Use a power drill to drill holes into your house.
• Locate rafters or trusses and drill holes in the exact center of
them.
• Determine whether there are water pipes, electrical wiring, or
gas lines hidden in the walls near where you will be drilling.
• Route coaxial cable through the foundation wall, under
floors, and through interior walls.
• Ground the satellite dish and coaxial cable as recommended
in the National Electrical Code (published by the National
Fire Protection Association, Batterymarch Park, Quincy, MA
02269).
If you do not feel comfortable performing these tasks or com-
plying with installation requirements, contact your dealer, or
call 1-866-347-3292 for information on having your system
installed by an authorized professional installer.
INSTALLATION AND YOUR HOME
The Federal Communications Commission (FCC) has a rule
that generally forbids local governments and homeowners
associations from preventing installation of DBS dishes one
meter or smaller in size (in Alaska, the dish size limit does not
apply). For more information, please visit the FCC’s Web site
at www.fcc.gov. Use the site search engine to find the FCC
Fact Sheet on Placement of Antennas.
BASIC STEPS OF SATELLITE DISH INSTALLATION
To install your satellite dish, follow these basic steps:
1. Install the software and receive modem so that you can
determine pointing values for your satellite dish
2. Choose an installation site
3. Select a mounting method
4. Install the mount
5. Assemble the satellite dish
6. Install the satellite dish on the mount
7. Run cable and ground wire to connect and ground the entire
assembly
8. Aim the satellite dish
N
ote: if you think you may later upgrade to th
e
two-way option (both receive and transmit signal
s
via satellite), you should at this time install th
e
antenna assembly in a location or manner no
t
readily accessible to children and at least 5 fee
t
above ground.

6
INSTALLING SOFTWARE AND LOCATING THE SATELLITE
Before you can install the satellite dish, you must select an installation site. Before you can select an installation site, you must deter-
mine the direction you will aim the satellite dish. You determine that direction by installing the system software, which will tell you
the direction.
The satellite is located approximately 22,300 miles in geostationary orbit above the equator. The satellite travels above Earth’s equa-
tor from west to east at a speed matching that of Earth’s rotation, thus appearing stationary in relation to the Earth’s surface. To aim
the satellite dish at the satellite, you need to know the azimuth, elevation, and polarization angles. As shown in the figures below, you
set the satellite dish to the correct azimuth angle by turning it from side to side, and set the elevation by tilting the dish up or down.
You set the polarization by rotating the satellite dish. The polarization setting rotates the satellite dish to the correct orientation for
your geographic location. This varies from one part of the country to another and is different for different satellites. Polarization is
positive in the eastern United States and negative in the western United States. Remember that it is important to pay attention to pos-
itive (+) and negative (-) signs when recording and using pointing values.
Before you install the satellite dish, the receive modem and software must be installed. To install the software, see the installation
guide that came with your software and indoor equipment for specific instructions. After you install the modem and software, run the
software program. It will take you to an Antenna Pointing screen, where you will be asked to enter your location or zip code. The
software will provide the azimuth, elevation, and polarization angles. Write them below. The pictures below will help you visualize
these terms.
Elevation: Azimuth: Polarization:
Elevation Down
Azimuth Right
Polarization
Positive
Elevation Up
Azimuth Left
Polarization
Negative

7
CHOOSING WHERE TO INSTALL THE SATELLITE DISH
TOOLS NEEDED
• Hand-held magnetic compass
• Angle finder or protractor
• Carpenter’s level or straight edge
Perform the following steps to select the best site to install the
satellite dish.
1. Go to the location where you plan to install the satellite
dish. It should be a close as possible to the computer, to
minimize the length of the cable run. If the total cable length
required is more than 150 feet see the cable specifications
on page 9.
2. Face south and hold the compass level so the needle can
rotate freely. When the needle stops rotating, it will be
pointing north. Carefully, so as not to disturb the needle,
rotate the body of the compass so that the 0° or Nmark
printed on the compass aligns with the painted end of the
needle. The compass is now aligned with magnetic north.
Note: Metal near the compass may affect your reading. If you are
standing near a metal structure, such as a shed or air conditioning
unit, move several feet away and repeat the measurement. Holding the
compass too close to a large metal belt buckle can have the same
effect.
3. Draw an imaginary line from the center of the compass to
the azimuth value you recorded on page 6. This is the direc-
tion to point the satellite dish. Use a rock or some other
object to mark the location where you are standing. Then
pick a landmark in the distance that aligns with the mag-
netic azimuth bearing, or mark the azimuth direction in
some other way.
.
CAUTION
• People can trip, fall into or otherwise bump into the sat-
ellite dish.
• Lacerations, bruises, or other impact injuries could
occur.
• Choose an installation site away from where people
are likely to work, ride, or play.
Figure 1
0
330
300
270
240
210
180
150
120
90
60
30
N
W
S
E
NW
SW
SE
NE
Example 2
160° Azimuth
Example 1
225° Azimuth

8
CHOOSING WHERE TO INSTALL THE SATELLITE DISH
4. Using the angle finder and a carpenter’s level or straight
edge, verify that there is an unobstructed line-of-sight
toward the satellite as shown in the diagram below. To do
this, align the level along the azimuth bearing. Then, using
the angle finder, lift the front end of the straight edge to cor-
respond to the elevation angle you recorded on page 6. Sight
along the straight edge to verify that there are no obstruc-
tions (such as buildings or trees) blocking the view. Take
into account future tree growth; if you are installing during
the fall or winter, take into account spring and summer leaf
growth. Also, avoid installing the satellite dish next to elec-
trical equipment such as air-conditioning units, because they
can cause signal interference.
Figure 2
Good View
(Clear line-of-sight, no
obstru tions in the way)
Poor View
(Obstru ted line-of-
sight, trees are blo k-
ing the signal)
123
2 1
90
45
0
45
90
45
0
45
123
2 1
90
45
0
45
90
45
0
45

9
CABLE SPECIFICATIONS
Note: Coaxial cables with copper clad steel center conductor are not recommended.
Note: Do not use splitters.
Note: Line amplifiers are required for Receive cable runs of more than 150 ft.
You must use plenum grade cable if the cable is to be run in plenum space which is carrying return air for the air circulation system,
Check local laws to see if plenum grade cable is required in other locations.
If the Receive cable run length is less than 150 ft., then no line amplifier is required. If the Receive cable run length is greater than
150 ft., but less than 300 ft., then install a line amplifier in the Receive cable only, a minimum of 25 ft. and up to 30 ft. from the LNB.
A line amplifier, if needed, can be installed only in the Receive cable, not in the Transmit cable. (There is no Transmit cable in the
one-way product.)
Line amplifier specification: Channel Master 5113 IFD or equivalent.
Grounding and Cable Choice
Your choice of grounding scheme may affect your choice of cable; see “Overview of
Grounding the Satellite System” on page 31 for information about grounding. Note that
meeting the National Electrical Code grounding requirements is easier if you use RG-6 with
solid copper center conductor and quad shield. However, you can also meet the
requirements by using RG-6 with solid copper center conductor only and grounding the
mast as described in the Overview.
Recommended cable specifications for Two-Way and One-Way Systems
Cable length from satellite
dish to computer Type of cable to be used
Receive Transmit
Up to 300 ft. RG6 with solid copper
center conductor
(CommScope 5729 or
equivalent)
RG6 with solid copper
center conductor
(CommScope 5729 or
equivalent)
300 ft. to 420 ft. RG6 with solid copper
center conductor
(CommScope 5729 or
equivalent)
RG6 with solid copper
center conductor and quad
shield (CommScope 5781
or equivalent)
Important: A higher grade of cable can be used for an installation where a lower grade is
specified. For example, an RG6 cable with solid copper center conductor and quad shield
can be used for installations where the cable length is less than 300 ft. Never use a lower
grade of cable than specified. Be sure to record the grade of the cable used for your
installation. The grade is printed on the cable every few feet. Never use a cable which
does not have the manufacturers name and its grade clearly printed on it!

10
SELECTING A MOUNTING OPTION
Based on the satellite dish installation site, decide on the best
surface for mounting your satellite dish. The base plate and
mast assembly that came with your satellite dish is called a uni-
versal mount. Some mounting options require only the univer-
sal mount. Other mounting options require that you also use
the two struts (called a brace kit) that came assembled with
your satellite dish kit. The struts slip over the mast and provide
addition support.
Note: If you plan to later upgrade your system to two-way (both
receive and transmit signals via satellite), you must install the satellite
dish in a location not readily accessible to children and at least 5 feet
above ground to avoid any risk of harm from radio frequency energy
emitted when transmitting signals to the satellite.
Note: Professional installation of your one-way satellite dish is
strongly recommended. If you do install the satellite dish yourself, you
must:
• Follow the instructions in this manual precisely
• Install the satellite dish no higher than 30 feet above grade
• Install the satellite dish only on approved surfaces, and NOT on
any other surfaces
• If necessary, be able to locate wood members from behind the roof
• If necessary, install lag screws in the center of wood members
INSTALLING THE SATELLITE DISH ON A WOOD DECK POST
You can use the universal mount to install the satellite dish on a
6-inch x 6-inch Southern Pine wood deck post.
See “Installing The Mount on a Wooden Deck Post” on
page 12.
INSTALLING THE SATELLITE DISH ON TYPICAL WOOD
ROOF CONSTRUCTION
You can use the universal mount and brace kit to install the sat-
ellite dish on typical wood roof construction.
See “Installing the Mount on a Wood Framed Roof” on
page 15.
CAUTION
• Before installing the universal mount brace kit, you
should obtain an analysis from a structural engineer to
confirm that the installation site is suitable for mounting
your satellite dish using the brace kit.
• Failure to ensure that the installation site is capable of
supporting the weight of the satellite dish could result
in personal injury or property damage.
CAUTION
The satellite dish should not be installed on a wood frame
roof unless the interior of the roof is unfinished so that
placement of lag screws can be verified and the roof
reinforced if necessary.
Figure 3
Figure 4
G-218
12/18/

11
SELECTING A MOUNTING OPTION
INSTALLING THE SATELLITE DISH ON CONCRETE OR CON-
CRETE MASONRY WALLS
You can use the universal mount to install the satellite dish on
concrete masonry or concrete walls. The brace kit can also be
installed for greater stability, but is not required.
See “Installing the Mount on Concrete or Concrete
Masonry walls” on page 20.
INSTALLING THE SATELLITE DISH ON A METAL POLE
You can install the satellite dish directly on a 9-foot metal pole.
If you choose this mount option you will not need the universal
mount or universal mount brace kit. Store them for possible
future use.
See “Installing the Mount Onto a Metal Pole” on page 22.
Figure 5 Figure 6

12
INSTALLING THE MOUNT ON A WOODEN DECK POST
The satellite dish can be installed on a 6-inch x 6-inch Southern Pine wood deck support post. The post can be no more than 8 feet
tall. It must be adequately attached at top and bottom. Posts made of other species of wood may be used as long as their material
properties match or exceed those of Southern Pine. Posts made of other species of wood whose material properties do not match or
exceed those of Southern Pine require engineering evaluation and approval before being used. The satellite dish may not be installed
on an unsupported wooden post.
PARTS NEEDED TOOLS NEEDED
•Lag screws, 3/8-inch x 4-inch, Qty: 6
•Washers, 3/8-inch, Qty: 6
•Silicone sealant
•Carpenter’s level
•Pencil
•Ruler
•9/16 and 1/2-inch socket wrench
•Electric drill
•Drill bits, 3/8, 1/4, and 1/8-inch
•Torque wrench
(capable of torquing
up to 18 ft-lbs)
•Ladder
Figure 7

13
INSTALLING THE MAST ONTO A WOODEN DECK POST
INSTALLATION PROCEDURE
Note: for an installation to be successful, the mast must be plumb. Re-
plumb the mast whenever instructed to do so, and re-plumb it when-
ever you feel it is necessary.
1. Orient the universal mount so the square hole in the base
plate is at the top as in Figure 8 before installation.
2. Use a 1/2-inch socket wrench to loosen the adjustment nuts
and swing the mast so that it is oriented as in Figure 9.
3. Mark the centerline of the deck post.
4. With an assistant place the base plate on the centerline at the
spot you plan to install it (see Figure 8).
5. Loosen the pivot bolt and adjustment nuts and plumb the
mast in two perpendicular directions (see Figure 9). If you
successfully plumb the mast proceed to step 6. If you cannot
plumb the mast find another location to install the satellite
dish. Note: it is essential that the mast be plumb. If you can-
not make the mast plumb at this point, find another installa-
tion site.
6. Mark the center of the base plate’s top center hole.
7. Drill a hole on the center mark in the manner described
below. Note: to avoid drilling too deeply, wrap a piece of
masking tape around the drill bit shank at the proper depth
so that you can see when you should stop drilling.
Drill a 1/8-inch pilot hole 2 inches deep.
Going into the pilot hole, drill a 1/4-inch hole 4 inches deep.
Going into the 1/4-inch hole, drill a 3/8-inch hole to a depth
equal to the unthreaded portion of the 3/8-inch x 4-inch lag
screw.
8. Fill the holes with silicone sealant and apply silicone sealant
to the entire back side of the base plate. Apply enough so
that it will press out around the edges when it is fastened
down (see Figure 10). Doing this will help prevent water
from seeping into the wood.
DANGER
•If the satellite dish contacts electric power lines, you
will be killed or seriously injured.
•Before starting the installation procedure, make sure
there are no power lines nearby.
CAUTION
•The satellite dish cannot be installed on an unsup-
ported wood post of any size.
•Install the satellite dish only on a wooden deck post.
•Install the satellite dish only as described in this man-
ual.
Figure 8
Figure 9
Figure 10
Top left center Top
Bottom
Top center
Top right center
Bottom right
center
Bottom center
Bottom left center
All lag screws
3/8-inches x 4-inches Center line
G-21848
11/16/00
Mast
(top view)
Level
Mast
Plumb vial
Adjustment nut
(2 places)
Pivot bolt
Bubble must
be centered
between
marks
Carpenter's level
Bubble
Sealant

14
INSTALLING THE MAST ONTO A WOODEN DECK POST
9. Install a 3/8-inch washer on a 3/8-inch x 4-inch lag screw.
10. Use a 9/16-inch socket wrench to screw the lag screw into
the top center hole of the base plate (see Figure 11). You
may need to swing the mast out of the way temporarily.
Tighten the screw snugly so that the base plate can barely
move.
Do not pound the lag screws into the post with a hammer or mallet.
Doing so may split the wood and render the post unusable.
11. Re-plumb the mast in two perpendicular directions as you
did in step 5. You may need to make adjustments to the mast
and/or the base plate.
12. Tighten the lag screw snugly so that the base cannot move.
13. Use a 1/2-inch socket wrench to tighten the adjustment nuts.
14. Re-plumb the mast. (Tightening the nuts can move the mast
off plumb.) Note: the mast must be plumb before proceed-
ing.
15. Repeat step 6 and step 8 to drill holes for the top left center,
top right center, bottom left center, and bottom right center
holes. See Figure 11.
Note: You must mark the center of all remaining screw holes
accurately. A Stanley Jumbo Self Centering Nail Set or similar
product will produce the best results. A #6 washer can also be
used to guide your pencil as it marks the hole center
Note: the base plate must not move when you drill the holes.
16. Fill the holes with silicone sealant.
17. Install a 3/8-inch washer on each of the 3/8-inch x 4-inch
lag screws.
18. Use a 9/16-inch socket wrench to screw the lag screw into
the four holes. Do not tighten the screws fully.
19. Re-plumb the mast and snug down the four screws firmly.
20. Use a 1/2-inch socket wrench to loosen the mast adjustment
nuts and swing the mast down so you have access to the bot-
tom center hole.
21. Repeat steps 6 and 7 to drill holes for the bottom center
hole.
Note: the base plate must not move when you drill the hole.
22. Fill the hole with silicone sealant.
23. Install a 3/8-inch washer on the final 3/8-inch x 4-inch lag
screw.
24. Use a 9/16-inch socket wrench to screw the lag screw into
the lower center hole. Do not tighten the screw fully.
25. Re-plumb the mast and snug down the lag screw.
26. Use a torque wrench to sung down the mast adjustment nuts
to 18 ft.-lbs. Confirm the mast is plumb after torquing.
Note: The mast must be plumb before you can proceed. If you cannot
plumb the mast, repeat the installation or find another installation site.
Continue with section “Installing the Cap Onto the Satellite
Dish” on page 23.
Figure 11
Top left center Top
Bottom
Top center
Top right center
Bottom right
center
Bottom center
Bottom left center
All lag screws
3/8-inches x 4-inches Center line

15
INSTALLING THE MOUNT ON A WOOD FRAMED ROOF
You can install the satellite dish onto a wood framed roof. You must use the brace kit. The minimum size for roof truss members is 2
inches x 4 inches. Roof rafters must be nominal 2x material (2x4, 2x6, etc.) Either size roof rafters or trusses must be16 to 24 inches
on center. The roof surface must consist of relatively thin, resilient materials, such as asphalt or composite shingles, sheet metal, or
similar materials, over wood sheathing with a thickness of 3/4 inch or less. Satellite dishes cannot be installed on flat roofs, slate
roofs, or Spanish tile roofing made of clay or other brittle materials. The roof pitch (or slope) must be between 3:12 and 12:12.
All center hole lag screws must be centered in the rafter or truss to which they are attached. For this reason, you must be able to
locate rafters and trusses and the center of rafters and trusses with a high degree of accuracy, which can be difficult to do. Home con-
struction varies a great deal. Construction styles, materials, and dimensions can all vary widely. In addition, stud finders give false
readings on multilayered surfaces, such as a roof. Also, you need experience in home construction to be able to determine the exact
location of rafters and trusses and their centers. The satellite dish should not be installed on a wood frame roof unless the interior of
the roof is unfinished so that placement of lag screws can be verified and the rafters or trusses reinforced if necessary.
If you do not have the knowledge and experience to accurately locate rafters and trusses and the center of rafters and trusses with a
high degree of reliability, you should contact a professional satellite dish installer for installation.
Large-timber roofs with frequent spacing of members are also permitted. These are constructed of wood members larger than the
nominal 2x sizes, and include post and beam structures with members from 4 inches x 4 inches and larger. The members cannot be
spaced more than 24 inches on center. Their physical properties must match or exceed those of Spruce-Pine-Fir #2.
PARTS NEEDED TOOLS NEEDED
•Lag screws, 3/8-inch x 4-inch, Qty: 2
•Lag screws, 1/4-inch x 4-inch, Qty: 4 (5/16-inch x
4-inch recommended if available)
•Lag screws, 3/8-inch x 2-inch, Qty: 4
•Washers, 3/8-inch, Qty: 6
•Washers, 1/4-inch, Qty: 4 (5/16-inch if needed)
•Silicone sealant
•Carpenter’s level
•Pencil or chalk
•Ruler
•Socket wrenches, 7/16, 1/2, and 9/16-
inch
•Electric drill
•Drill bits, 3/8-, 1/4-, 1/8, and 5/32-inch
•Torque wrench (can torque up to 18 ft-
lbs)
•Ladder
Figure 12

16
INSTALLING THE MOUNT ON A WOOD FRAMED ROOF
INSTALLATION INSTRUCTIONS
Before you begin, make sure the rafters or trusses (called mem-
bers) in your house are located 16 to 24 inches on center.
Remember that 2 x 4 and 2 x 6 inch members are actually
1-1/2 inches thick.
Note: for an installation to be successful, the mast must be plumb. Re-
plumb the mast whenever instructed to do so, and re-plumb it when-
ever you feel it is necessary.
1. Orient the universal mount so the square hole in the base
plate is at the top as in Figure 13 before installation.
2. Use a 1/2-inch socket wrench to loosen the adjustment nuts
and swing the mast so that it is oriented as in Figure 14.
3. Mark the centerline of the rafter or truss.
.
DANGER
•If the satellite dish contacts electric power lines, you
will be killed or seriously injured.
•Before starting the installation procedure, make sure
there are no power lines nearby.
CAUTION
•Rafters or trusses must be located 16 to 24 inches
apart on center, except for large-timber roofs, which
can be located no more than 24 inches apart on cen-
ter.
•The roof surface must consist of relatively thin, resilient
materials, such as asphalt or composite shingles,
sheet metal, or similar materials, over wood sheathing
with a thickness that must not exceed 3/4 inch.
•Satellite dishes cannot be installed on slate roofs or
Spanish tile roofing made of clay or other brittle materi-
als.
•The roof pitch (also called slope) must be between
3:12 and 12:12.
•The satellite dish cannot be installed on a flat roof.
•Center hole lag screws
must
be centered in the rafter
or truss.
•The satellite dish should not be installed on a wood
frame roof unless the interior is unfinished so that
placement of lag screws can be verified and the roof
reinforced if necessary.
•Install the satellite dish only as described in this man-
ual.
CAUTION
If you do not have the knowledge and experience to
accurately locate rafters and the center of rafters with a
high degree of reliability, you should contact a professional
satellite dish installer for installation.
Figure 13
Figure 14
Corner holes
Corner holes
Top center hole
Bottom center hole
Centerline
Rafter or truss
Center hole lag
screws are 3/8 inches
by 4 inches
Corner lag screws
are 3/8 inches
by 2 inches
Mast
(top view)
Level
Mast
Plumb vial
Adjustment nut
(2 places)
Pivot bolt
Bubble must
be centered
between
marks
Carpenter's level
Bubble
T0
0