
3
a brand of Hugo Lahme GmbH
Stand 04/2013 Art.-Nr.: 578173
Einbauanleitung
1. Vom Technikgang aus den Abschlussdeckel des Unterwasserfensters öffnen.
2. Den Einschub-Scheinwerfer in das Unterwasserfenster stellen, positionieren und bis zur Glasscheibe vorschieben.
3. Die zwei Anschlusskabel durch die Kabelverschraubungen am Abschlussdeckel führen. Ausreichend Kabel im Unter-
wasserfenster aufgerollt lassen, um Wartungsarbeiten durchführen zu können.
Achtung: Beim Einbau in einem Unterwasserfenster Ø 250 mm sind die Füße am Einschub-Scheinwerfer zu demontieren!
Bei der Montage ist zwingend darauf zu achten, dass die Anschlusskabel nicht beschädigt werden!
4. Versorgungseinheit an der Wand im Technikgang anbringen.
5. Anschlüsse an der Versorgungseinheit laut Anschlussplan ausführen.
6. Abschlussdeckel der Fensteröffnung wieder korrekt positionieren und befestigen.
Achtung: Bei einer einfachen Verglasung des Unterwasserfensters muss der Abschlussdeckel wieder korrekt positioniert
und befestigt werden, um bei einem Glasbruch an der Fensterfront ein Einströmen des Schwimmbadwassers in den
Technikgang zu verhindern!
Installation instruction:
1. Open the locking cover of the underwater window from the technical passage.
2. Put the floodlight insertion into the underwater window, position it and move it towards the glass plate.
3. Put the two connection cables through the cable gland on the locking cover. Keep sufficient cable in the underwater
window for being able to do maintenance work.
Attention: When installing into an underwater window Ø 250 mm the feet of the floodlight insertion module have to
be disassembled! During installation it has to be ensured that the connection cables do not get damaged!
4. Attach the supply unit on the wall in the technical passage.
5. Conduct the connections on the supply unit according to the wiring diagram.
6. Reposition the locking cover of the aperture correctly and re-fix it.
Attention: In case of single pane windows the locking cover has to be correctly repositioned and re-fixed for avoiding
an influx of the pool water into the technical passage in case of a glass breakage.
Montage dans le bassin
1. De la galerie technique ouvrir le couvercle de la fenêtre subaquatique.
2. Pose du module dans la fenêtre subaquatique et positionner celui-ci jusqu’à la vitre de fermeture.
3. Introduire les deux câbles dans les presses étoupes du couvercle, prévoir assez de câble dans le boîtier pour
maintenance.
Attention:
En cas d'utilisation d'un fenêtre subaquatique avec Ø 250 mm les deux pieds en équerre sont à démonter !
Pour le remontage il est important que le couvercle soit bien positionné et de faire très attention que les câbles ne soit
pas endommagés !
4. Fixer l’alimentation au mur de la galerie technique.
5. Branchement à effectuer suivant le schéma.
6. Mise en place du couvercle de fermeture de fenêtre et fixation.
Attention: En cas de fenêtre de projecteur avec un verre simple de fermeture bien repositionner le couvercle de
fermeture de manière qu’en cas de rupture d’étanchéité l’eau de piscine ne puisse pas s’écouler dans la galerie technique.
Montage / Installation / Installation
Bei der Installation sind die geltenden Sicherheitsvorschriften zu beachten. Betrieb nur in trockener Umgebung! Empfohlene
Einbautiefe 600 bis 800 mm unterhalb des Wasserspiegels im Unterwasserfenster. Minimale Abmessungen des Unterwasserfensters
Ø 250 mm oder Ø 285.
During installation follow the applicable safety regulations. Operation only in dry places! Recommended installation depth is 600
up to 800 mm below the water level in the underwater window. Minimal dimensions of the underwater window are Ø 250 mm or
Ø 285 mm.
Pour installation de ce module projecteur de piscine respecter les normes applicables. Le module projecteur de piscine ne doit être
mis en service qu’en situation non-immergée dans le corps d’une fenêtre subaquatique de dimension minimum Ø 250 mm ou
Ø 285 mm. La profondeur de montage recommandée est de 600 à 800 mm au-dessous de niveau d'eau.
30er POWER LED 2.0 Einschub-Scheinwerfer
für Unterwasserfenster
30 POWER LED 2.0 floodlight insertion module
for underwater windows
30 POWER LED 2.0 projecteur
pour hublot local technique