Humantec Menopod User manual

®
User Guide
Mode d’emploi

Contents
Chapter 1: Getting to Know Your Menopod®
1 Menopod® Overview
2 Accessories
3 How It Works
Chapter 2: Getting Started
4 Charge Your Menopod®
4 Understanding the LED Indicators
Chapter 3: How to Use Your Menopod®
6 Warnings
6 Instructions For Using Your Menopod®
10 Troubleshooting
Appendix A: Safety, Handling & Support
11 Important Safety Information
12 Important Handling Information
14 Warranty

1
Getting to Know Your
Menopod® 1
Menopod® Overview
This guide describes the features of your Menopod®.
Accessories
LED INDICATORS
POWER SWITCH
MICRO-B USB CONNECTOR
COPPER PLATE

2
The following accessories are included with your
Menopod®.
Charging Cable
Use the Micro-B USB cable to connect any your Menopod®
to any USB power source and charge the battery.
USB Power Adapter
Use the USB power adapter to connect your Menopod® to a
power outlet and charge your Menopod® battery.

3
How It Works
The Menopod® is designed to be used during the onset of
when applied to the back of the neck, will provide relief
with non-hormonal intervention during menopausal
transition.
The Menopod® works by bringing the temperature of the
copper plate down to a cool 5OC (41OF) within four (4)
seconds, for a period of one (1) minute. As this process also
generates heat inside of the Menopod®, the Menopod®
can only be used a few times in rapid succession before
shutting itself down, in order to prevent overheating.
The Menopod® will then be unable to turn on until it has
The Menopod® is designed to operate in temperatures
between 0OC (60OF) and 35OC (90OF). At higher
temperatures, the Menopod® will achieve fewer cycles
before overheating.

4
Getting Started 2
Charge Your Menopod®
Before using your Menopod®, make sure that the battery
is fully charged. Connect your Menopod® to a USB Power
Adapter or USB port using the included Charging Cable,
and allow the Menopod® to charge until all four (4) LED
indicator lights are solid green.
Understanding The LED Indicators
The LED Indicators display the status of your Menopod
when it is in use or charging. Please see the descriptions
below:
• • • •
Solid when turned on or charging: Battery is fully charged.
Blinking while charging: Almost fully charged.
• • • •
Solid when turned on: At least three (3) quarters of battery
remaining.
Blinking while charging: Battery charged to at least 75%.
• • • •
Solid when turned on: At least half of battery remaining.
Blinking while charging: Battery charged to at least 50%.

5
•• • •
Solid when turned on: Battery nearly depleted.
Blinking while charging: 1%-25% of battery remaining.
• • • •
Blinking while operating: Battery too low to operate. Needs
to be recharged
• •••
Blinking while connected to charging cable: Over-
discharged. See Troubleshooting for more details.
• • • •
Blinking while operating: Overheated. Allow up to ten (10)
minutes for Menopod® to cool.
• • • •
No lights when switch is slid sideways: Battery depleted.
Unit must be recharged
No lights when charging: No power. See Troubleshooting
for more details.

6
How to Use Your
Menopod® 3
Warnings
Do not leave your Menopod® in your car on a hot or cold
day. Excessive heat or cold may cause damage to the
operation of the device. The copper plate can become very
hot if left in the heat.
The Menopod® should not be submerged into water. If
unit is submerged, do not use the device.
Instructions for Using Your Menopod®
1. If the Menopod® is currently charging, disconnect the
Menopod® from the Charging Cable.

7
2. Slide the power button to the left of to turn the
Menopod® on.
3. Your Menopod® will cool to 5OC (41OF) within four (4)
seconds.

8
4. Place the Menopod® on the back of your neck for
instant cooling relief.
5. Slide the Menopod® from side to side on the back of
your neck every ten (10) seconds.