Hummer H-120 User manual

H-120, H-240 &
H-360 ARGB

EN - Warning
Improper installation will result in damage to the processor. Never switch the computer system on until the cooler and the
fans are connected to the motherboard power connector.
Always use the included screws. Screw the radiator with care to avoid damaging it.
Electrostatic discharge (ESD) can damage system components. Use and ESD-controlled workstation. If a worksation is not
available, wear an antistatic wrist strap or touch an earthed surface before handling any PC components.
PT - Atenção
Uma instalação imprória poderá danicar o processador. Nunca ligue o computador sem vericar se o cooler e as ventoinhas
estão ligadas na motherboard.
Utilize sempre os parafusos fornecidos. Aparafuse o radiador com cuidado de forma a evitar possíveis danos.
Descargas eletroestáticas (ESD) poderão danicar componentes do PC. Use uma bancada com controle de ESD. Caso não
tenha uma bancada disponível, utilize uma pulseira anti-estática ou toque uma superfície aterrada antes de manusear
qualquer componente do PC.
ES - Advertencia
Una instalación inapropriada puede provocar daños al procesador. Nunca encienda el ordenador antes de que el cooler y los
ventiladores estén conectados al conector de corriente de la placa madre.
Utilice siempre los tornillos originales. Cuidado con no dañar el radiador al atornillar.
Descargas electrostáticas (ESD) pueden dañar componentes en el sistema. Use una estación de trabajo con control de ESD.
Si no tiene disponible dicho lugar de trabajo, colóquese una muñequera antiestática o toque una supercie conectada a tierra
antes de tocar cualquier componente en el PC.
FR - Advertissement
Une installation incorrecte endommagerait le processeur. N’allumez jamais l’ordinateur avant que le ventilateur e le
refroidisseur ne soit connecté au connecteur d’alimentation de la carte mère. Ne mettez jamais le système sous tension
jusqu’à ce que le refroidisseur et les ventilateurs soient connectés au connecteur d’alimentation de la carte mère.
Utilisez toujours les vis fournies. Vissez le radiateur avec précaution pour éviter de l’endommager.
Une décharge électrostatique (ESD) peut endommager les composants du systéme. Utilisez une station de travail protégée
contre l’ESD. Si vous ne disposez pas d’une telle station de travail, portez un bracelet antistatique ou touchez une surface
connectée à la masse avant de manipuler les composants du PC.
DE - Warnung
Fehler bei der Installation können zu Schäden am Prozessor führen. Schalten Sie das Computersystem niemals ein, bis der
Kühler und die Lüfter an den Netzanschluss angeschlossen sind.
Verwenden Sie immer die mitgelieferten Schrauben. Schrauben Sie den Kühler sorgfältig, um eine Beschädigung zu
vermeiden.
Die Systemkomponenten können durch elektrostatische Entladung beschãdigt werden. Benutzen Sie einen for ESD
schützenden Arbeitsplatz. Sollte ein solcher Arbeitspaltz nicht verfügbar sein, tragen Sie ein antistatisches Armband or
berühren Sie eine geerdete Oberãche vor dem hantieren mit PC Komponenten.
IT - Avvertimento
L’installazione non corretta si tradurrà in danni al processore. Non accendere il sistema informatico no al dispositivo di
raffreddamento ei ventilatori sono collegati al connettore di alimentazione della scheda madre.
Usare sempre le viti in dotazione. Avvitare il radiatore con cura per evitare di danneggiarla.
Le scariche elettrostatiche (ESD) possono danneggiare i componenti del sistema. Uso e workstation ESD-controllato. Se un
worksation non è disponibile, indossare un bracciale antistatico o toccare una supercie messa a terra prima di maneggiare
qualsiasi componente del PC.

Important announcement
Please read this user’s manual carefully before installation to get the water cooler’s best
performance by optimized installation. Nox Xtreme is not responsible for any damage to the product
or injury caused by incorrect installation or user’s carelessness. The water cooler may cause
interference with some motherboards. If you face an interference between Hummer cooler and
your motherboard, please stop installing it. Be careful not to hurt yourself by the radiator while
installating & disassembling the water cooler. Do not move the water cooler around after the
installation to prevent CPU damage. Please, do not use the water cooler for any other usage apart
from the original purpose.
Warranty
For your warranty claims, please contact Nox Xtreme overseas distribution partners in your
country. Find the distribution partner list at www.nox-xtreme.com
Warranty: 2 years from purchasing date. (Depending on the laws of each country)
URL: www.nox-xtreme.com
E-mail: [email protected]
Components description
EN
1) Radiator mounting screws [x8]
2) Fan mounting screws [x8]
3) Intel LGA2066/11 Standoff [x4]
4) AMD TR4 Standoff [x4]
5) Thermal Grease [x1]
6) Insulative Washer [x4]
7) Knurled Treaded Nut [x4]
8) Tightening Nut [x4]
9) Backplate [x1]
10) Long Screw [x4]
11) Intel Bracket [x1]
12) AMD Bracket [x1]
1
5
9
2
6
10
3
7
11
4
8
12

AB
Backplate mounting holes illustration
Intel mounting
Intel mounting: LGA1150 / 1151 / 1155 / 1156 / 1366 / 1200 installation
Intel bracket mounting
LGA 1366
LGA 1150 / 1151 / 1155 / 1156
Socket
AM3+ / AM3 / AM2+ / FM2+ / FM2 / FM1
Socket AM4
Align the arrows on the bracket and the pump
base, turn the bracket clockwise to secure it to
the pump base.
Choose the right mounting holes
according to CPU Socket. Insert the
long screws through the backplate and
then through the motherboard.
9
10
* Intel bracket is universal for
LGA2066 / 2011 / 1150 / 1151 / 1155 / 1156 / 1366
7
6
Put the washer onto the long screws
rst, and then fasten the knurled
threaded nuts into the screws.
continues in next page

CD
A
B
C
Put the pump onto the CPU. Secure the
block using the tightening nuts.
Clean the CPU surface and apply a
thin layer of thermal grease onto
the surface.
Thread the LGA20XX standoff into the
mounting holes on the motherboard.
Clean the CPU surface and apply a
thin layer of thermal grease onto
the surface.
Put the pump onto the CPU. Secure the
block using the tightening nuts.
5
Intel mounting: LGA2066 / 2011 installation
8
3
5
8
AMD mounting
AMD bracket mounting
Align the arrows on the bracket and the pump
base, turn the bracket clockwise to secure it to
the pump base.
* AMD bracket is universal for
TR4 / AM4 / FM2(+) / FM1 / AM3(+) / AM2(+)
comes from previous page

A
B
C
D
A
B
C
AMD mounting: AM4 / FM2(+) / FM1 / AM3(+) / AM2(+) installation
AMD mounting: TR4 / TRX4 installation
Choose the right mounting holes
according to CPU Socket. Insert the
long screws through the backplate and
then through the motherboard.
Thread the TR4 standoff into the
mounting holes on the motherboard.
7
6
Put the washer onto the long screws
rst, and then fasten the knurled
threaded nuts into the screws.
Clean the CPU surface and apply a
thin layer of thermal grease onto
the surface.
Put the pump onto the CPU. Secure the
block using the tightening nuts.
Clean the CPU surface and apply a
thin layer of thermal grease onto
the surface.
Put the pump onto the CPU. Secure the
block using the tightening nuts.
9
10
4
5
5
8
8

Fan & radiator mounting
HUMMER H-240 ARGB lighting connection guide
Connection through motherboard RGB control
Connection through internal RGB controller
Use the fan mounting screws to secure
the fan(s) onto the radiator.
ASUS: ADD_HEADER
MSI: JRAINBOW
GIGABYTE: D_LED
ASROCK: ADDR_LED
Use the radiator mounting screws to
secure the radiator to the case panel.
2
1
A) Download RGB Sync software compatible with your motherboard from
its manufacturer’s ofcial website to adjust RGB color / mode.
Switch lighting modes with "M" button
B) Use RGB Splitter to Connect Pump / Fans’
RGB Cables.
M
C
S
Switch color modes with "C" button
Change color speed with "S" button
CAUTION!
Wrong connection
will damage the
device and cause
malfunction!