Hunter Hunter Ceiling Fan User manual

42607-01 • 02/16/06
For Your Records and Warranty
Assistance
Model Name:
_____________________
Catalog/Model No.:
________________
Serial No.:
_______________________
Date Purchased:
___________________
Where Purchased:
_________________
For reference also attach your receipt or a
copy of your receipt to the manual.

2
Hunter Fan Company
42607-01 • 02/16/06
3
Table of Contents
1 • Getting Ready
...................................................
4
2 • Installing the Ceiling Plate
..........................
5
3 • Assembling the Fan
.......................................
6
4 • Hanging and Wiring the Fan
.....................
7
5 • Installing the Canopy and Canopy
Trim Ring
.............................................................
8
6 • Assembling the Blades
.................................
9
7 • Completing Your Installation With
or Without a Light Fixture
.......................
10
8 • Operating and Cleaning
Your Ceiling Fan
............................................
14
9 • Troubleshooting
...........................................
16
Welcome
© 2006 Hunter Fan Company
Your new Hunter
®
ceiling fan is an addition to your home or o ce that
will provide comfort and performance for many years.  is installation
and operation manual gives you complete instructions for installing
and operating your fan.
We are proud of our work. We appreciate the opportunity to supply
you with the best ceiling fan available anywhere in the world.
Before installing your fan, for your records and warranty assistance,
record information from the carton and Hunter nameplate label
(located on the top of the fan motor housing).
Cautions and Warnings
•
Read this entire manual carefully before beginning installation. Save
these instructions.
•
Use only Hunter replacement parts.
•
To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to these instructions,
and use only the hardware supplied.
•
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning o the circuit breakers to the
outlet box and associated wall switch location. If you cannot lock
the circuit breakers in the o position, securely fasten a prominent
warning device, such as a tag, to the service panel.
•
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
quali ed electrician.
•
To reduce the risk of personal injury, do not bend the blade
attachment system when installing, balancing, or cleaning the fan.
Never insert foreign objects between rotating fan blades.
•
To reduce the risk of  re, electrical shock, or motor damage, do not
use a solid-state speed control with this fan. Use only Hunter speed
controls.

2
3
42607-01 • 02/16/06
Hunter Fan Company
Installer’s Choice and Optional Accessories
Low Pro le Mounting
 ts close to the
Low Pro le Mounting  ts close to the Low Pro le Mounting
ceiling, recommended for ceilings less
than 8 feet high
Standard Mounting
hangs from
Standard Mounting hangs from Standard Mounting
the ceiling by a downrod (included),
recommended for ceilings 8 feet or higher
Angle Mounting
recommended for a
Angle Mounting recommended for a Angle Mounting
vaulted or angled ceiling
Understanding Mounting and Installer’s Choice
®
Hunter’s patented 3-position mounting system provides you maximum
installation  exibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Pro le, Standard, or Angle mounting.  e steps in this manual include
instructions for all three Installer’s Choice mounting methods.
Considering Optional Accessories
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
For ceilings higher than 8 feet, you
can purchase Hunter extension
downrods. All Hunter fans use sturdy
3/4” diameter pipe to assure stability
and wobble-free performance.

4
Hunter Fan Company
42607-01 • 02/16/06
5
1 • Getting Ready
To install a ceiling fan, be sure you can do the following:
•
Locate the ceiling joist or other suitable support in ceiling.
•
Drill holes for and install wood screws.
•
Identify and connect electrical wires.
•
Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
•
Electric drill with 9/64” bit
•
Standard screwdriver (magnetic tip recommended)
•
Phillips-head screwdriver (magnetic tip recommended)
•
Wrench or pliers
•
Ladder (height dependent upon installation site)
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326.
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum e ciency, and energy savings.
Installing Multiple Fans?
If you are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in sets,
as they were shipped.

4
5
42607-01 • 02/16/06
Hunter Fan Company
2 • Installing the Ceiling Plate
CAUTION:
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning o the circuit breakers to the outlet box
and associated wall switch location. If you cannot lock the circuit breakers
in the o position, securely fasten a prominent warning device, such as a
tag, to the service panel.
2-1.
Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box.  e pilot holes should be 9/64”
in diameter.
For Angled Ceilings:
Be sure to orient the ceiling plate so that the
two tabs are pointing towards the ceiling peak.
2-2.
Your fan comes with four preinstalled noise isolators. Check to
make sure all four isolators are in place and were not removed
during shipment.
2-3.
Place a  at washer on each of the two 3” wood screws.
2-4.
 read the supply wires from the outlet box in the ceiling through
the hole in the center of the ceiling plate.
2-5.
Align the slotted holes in the ceiling plate with the pilot holes you
drilled in the wood support structure. For proper alignment use
slotted holes directly across from each other.
Note:
 e isolators should be  ush against the ceiling.
2-6.
Pass the screws through the slotted holes in the ceiling plate into
the pilot holes you drilled.
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Flat Washer
3” Wood
Screw
Steps 2-3 – 2-6
Ceiling
Ceiling
Plate
Plate
For Angled Ceilings:
Be sure to orient
the ceiling plate so that the two tabs
are pointing towards the ceiling peak.
Towards
Ceiling Peak

6
Hunter Fan Company
42607-01 • 02/16/06
7
3 • Assembling the Fan
Steps 3-2 – 3-3
Low Pro le
Washer
Downrod
Canopy
Set Screw
Low Pro le Screw
WARNING:
Fan may fall if not assembled as directed in these
installation instructions.
3-1.
Unbundle the wires from the fan.
For Standard or Angle mounting:
3-2.
Insert the downrod through the canopy and canopy trim ring.
Feed the wires from the fan through the downrod on one side of
the pin in the ball.
3-3.
Loosen the square head set screw on the adapter to install the
pipe and ball assembly.
Note:
When the pipe and ball assembly
is fully installed, 2-3 threads on the pipe will still be visible; this is
normal. Securely retighten the set screw with a wrench or pliers.
Go to
4 • Hanging and Wiring the Fan
.
CAUTION:
 e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
For Low Pro le mounting:
Note:
For low pro le mounting, the downrod is replaced with the
low pro le washer.
3-4.
Remove the set screw from the adapter.
3-5.
Place the low pro le washer into the canopy with the lip down.
3-6.
Align the holes in the washer with the holes in the adapter.
Assemble securely with three low pro le screws.
Go to
4 • Hanging and Wiring the Fan
.
Canopy
Trim Ring
Green
Ground
Wire
Standard or Angle Mounting
Low Pro le Mounting
Low Pro le
Screws
Canopy
Canopy
Trim Ring
Adapter
Adapter
Low Pro le
Low Pro le
Washer
Low Pro le Screw
Low Pro le Screw
Adapter
Steps 3-5 – 3-6
Step 3-6 (Detail)

6
7
42607-01 • 02/16/06
Hunter Fan Company
4 • Hanging and Wiring the Fan
4-1.
Raise the fan and align the slots in the canopy with the hooks on the
ceiling plate.
Note:
To hang the fan, you must tilt the canopy to an almost vertical
position so that the canopy slots sit on the ceiling plate hooks.
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
quali ed electrician.
Wall switches are not included. Select an acceptable general-use switch in
accordance with national and local electrical codes.
4-2.
Make sure the power to the outlet box and associated wall switch
location is still OFF.
To connect the wires, hold the bare metal leads together and place a
wire nut over them, then twist the wire nut clockwise until tight.
CAUTION:
Be sure no bare wire or wire strands are visible after
making connections.
Single Switch Wiring:
If you want to, you can control both fan and light with one switch. To
do so connect the wires as follows:
•
 e bare or green ground wire from the ceiling to the green
ground wire from the ceiling plate and the green ground wire
from the fan
•
 e white wire from the ceiling to the white wire from the fan
•
 e black wire from the ceiling to the black and the black/white
wire from the fan
Dual Switch Wiring:
•
 e bare or green ground wire from the ceiling to the green
ground wire from the pipe ball assembly
•
 e white wire from the ceiling to the white wire from the fan
•
 e black wire from the ceiling to the black wire from the fan
•
 e black/white wire from the fan to the wire for the wall switch
4-3.
Push all wires and wire nuts into the outlet box.
Single Switch Wiring
Dual Switch Wiring
Wire Nut

8
Hunter Fan Company
42607-01 • 02/16/06
9
5 • Installing the Canopy and Canopy Trim Ring
WARNING:
Failure to complete the following steps could cause the fan
to fall.
Note:
It is recommended you use a magnetic tip screwdriver for the
following steps.
5-1.
Rotate the hanger ball so the tab in the canopy is secure in the
hanger ball groove.
Note:
Your fan may have multiple tabs and
grooves that must be aligned.
5-2.
Swing the fan up to align the canopy screw holes with the
mounting holes on the ceiling plate.
WARNING:
 e slots in the canopy must remain engaged while
swinging the canopy for alignment.
5-3.
Holding the canopy up with the screw holes aligned, partially
install two canopy screws into the holes opposite the ceiling plate
tabs.
5-4.
Partially install a canopy screw between the slots in the canopy.
When all the holes are properly aligned, securely tighten all three
canopy screws.
5-5.
Verify that the tabs in the canopy are still in the grooves of the
hanger ball.
5-6.
Align the tabs on the trim ring opposite the grooves in the hanger
ball. Using both hands, push the canopy trim ring up to the top of
the canopy.  e canopy trim ring will snap and lock into place.
Note:
Should you need to remove the trim ring, press  rmly on
opposite sides of the trim ring directly above the groove in the
hanger ball.  e tabs will  ex out releasing the canopy trim ring.
Step 5-1
Step 5-1
Step 5-2
Groove
Tab
Step 5-3
Canopy Screw
Canopy
Trim
Ring
Canopy

8
9
42607-01 • 02/16/06
Hunter Fan Company
6 • Assembling the Blades
Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).
6-1.
Your fan may include blade grommets. If your fan has grommets,
insert them by hand into the holes on the blades.
6-2.
Attach each blade to a blade iron using three blade assembly
screws. If you used grommets, the blades may appear slightly loose
after screws are tightened.  is is normal.
6-3.
Some blade mounting screws are installed in the motor to
secure shipping blocks. Remove the blade mounting screws and
rubber bumpers from the motor. Save the screws and discard the
bumpers.
6-4.
For each blade, insert one blade mounting screw through the
blade iron, and attach lightly to the fan. Insert the second blade
mounting screw, then securely tighten both mounting screws.
Step 6-1 (Detail)
Grommet
Blade Assembly
Screws
Use with grommet
Use without grommet
Blade
Mounting
Screw
Steps 6-1 – 6-2
Step 6-4

10
Hunter Fan Company
42607-01 • 02/16/06
11
7 • Completing Your Installation With or Without a Light Fixture
Steps 7-1 – 7-3
Housing
Assembly
Screw
Upper
Switch
Housing
Your Hunter fan comes with an optional light  xture assembly.  is
feature gives you the option of installing the fan with OR without the
included light  xture.  e steps below direct you whether or not you
are installing a light  xture.
WARNING:
Use only the light  xture supplied with this fan model.
7-1.
To attach the upper switch housing, partially install two housing
assembly screws into the switch housing mounting plate.
7-2.
Feed the upper plug connector through the center opening of the
housing.
7-3.
Align the keyhole slots in the housing with the housing assembly
screws.
7-4.
Turn the housing counterclockwise until the housing assembly
screws are  rmly situated in the narrow end of the keyhole slots.
Install the remaining housing assembly screw into the housing.
Tighten all three screws  rmly.
CAUTION:
Make sure the upper switch housing is securely
attached to the switch housing mounting plate. Failure to properly
attach and tighten all three assembly screws could result in the
switch housing and light  xture falling.
7-5.
If you want to install the light  xture
, proceed with step 7-6 on
page 12 now.
If you do not want to install the light  xture
, you need to
uninstall it now. See “Uninstalling the Light Fixture” on page 11.
Once you have uninstalled the light  xture, continue with step
7-6.
Step 7-4