Hunter Hunter Ceiling Fan User manual

www.HunterFan.com 1.888.830.1326
PAGE
7
PAGE
11
PAGE
5
PAGE
6
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation Ceiling Bracket
Ladder
PAGE
3
Tools Needed
Wiring Canopy
Operation,
Maintenance
& Cleaning Troubleshooting
Downrod
Preparation
Table of Contents
PAGE
12
Congratulations on purchasing
your new Hunter® ceiling fan!
It will provide comfort and
performance in your home
or ofce for many years. This
installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling
fan available anywhere in the
world.
To register your fan please visit:
www.HunterFan.com/register
PAGE
4
Mounting Options
PAGE
15
Blades
Auto Balance™ Switch Housing Light Kit
PAGE
13
PAGE
14
PAGE
16
PAGE
18
?
?
?
PAGE
20
Remote Control
Settings
PAGE
10
1
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
M3500-01 •11/30/12 • © Hunter Fan Company
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
30 inches
from blade tip
to nearest wall
or obstruction 7 feet
from bottom
edge of blade
to the oor
Select a downrod length
Assess ceiling angle
Must be able to
secure the fan to
building structure or
fan-rated outlet box
1
2
3
Standard Downrod
for ceilings 8-10 feet high
Shorter Downrod
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet or higher
2
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS
w.1 - To reduce the risk of re, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage,
use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualied electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
This product may cause interference to radio equipment and
should not be installed near maritime safety communications
equipment, ships at sea, or other critical navigation or
communications equipment operating between 0.45-30 MHz.

www.HunterFan.com 1.888.830.1326
Tools Needed
Ladder
Power Drill
(optional)
9/64” Drill Bit
(optional)
Screwdrivers
Pliers Wire Strippers
If mounting to a support structure, you will also need these tools.
3
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
4
M3500-01 •11/30/12 • © Hunter Fan Company
1.866.268.1936
If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Guide Touches
BOTH Ceiling & Wall
S
I
T
U
A
T
I
O
N
1
Guide Touches Wall
but NOT Ceiling
S
I
T
U
A
T
I
O
N
2
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
Downrod
*most common
If you have a at ceiling:
Hang your fan by a standard downrod (included).
Mounting Options
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
4
34OCEILING
WALL
OPTION
1
Standard
Mounting
OPTION 2
Angled
Mounting
2 3
SLIDE
toward ceiling
PLACE
against wall
1
FOLD
on dotted line
34°
Use the three steps below to determine if your ceiling angle is greater than 34°
Support
Structure
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Standard
Mounting
Style
Support
Structure
Ceiling
Outlet Box
(required)
M3500-01 •11/30/12 • © Hunter Fan Company

1.888.830.1326
www.HunterFan.com
Ceiling Bracket
OFF
Make sure all four (4) bumpers
are still attached.
For angled ceilings, point
opening toward peak.
Refer to warning w.1 on pg. 2
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
Turn Power
5
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Ceiling Bracket (continued) Preparation 1.888.830.1326
www.HunterFan.com
D
I
S
C
A
R
D
K
E
E
P
!
Remove the shipping blocks from the
motor. Save the screws. They will be
needed for blade iron installation.
Time Saver Tip: Get a helper
to insert grommets, found in
the hardware bag, into the
blades while you’re doing the
next couple of steps.
6
M3500-01 •11/30/12 • © Hunter Fan Company

1.888.830.1326
Downrod
Slide
Slide
1 2 3 4 5
678910
Sold Separately
Included
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Standard
Downrod
for ceilings 8-10’ high
Option 1Option 2
Option 3
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Steps 6-10 to reassemble with new pipe
Included (pre-assembled)
www.HunterFan.com
7
M3500-01 •11/30/12 • © Hunter Fan Company

KEEP!
8”
3/8”
C
U
T
&
S
T
R
I
P
(not to scale)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Downrod (continued)
8” 3/8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
If the setscrew is not tightened
securely, the fan may fall.
K
E
E
P
!
1.888.830.1326
www.HunterFan.com
8
M3500-01 •11/30/12 • © Hunter Fan Company

1.888.830.1326
9
M3500-01 •11/30/12 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.

www.HunterFan.com 1.888.830.1326
Remote Control Settings
Receiver
DIP
Switches
Transmitter
Jumpers
Battery
CFL Toggle
Switch
Dip Switches
Set to 01110
Dip Switches
Set to 01001
Dip Switches
Set to 01110
Dip Switches
Set to 01001
Receiver 1 Receiver 2
Transmitter 2Transmitter 1
Example DIP Switch Settings
DIP Switches
Set to 0111
DIP Switches
Set to 0100
DIP Switches
Set to 0100
DIP Switches
Set to 0111
4321
4321
4321
4321
4 = off
3 = on
2 = on
1 = on
4 = off
3 = on
2 = off
1 = on
Example Jumpers Settings
Receiver 1 Receiver 2
Transmitter 2Transmitter 1
4321
4321
4321
4321
4 = off
3 = on
2 = on
1 = on
4 = off
3 = on
2 = off
1 = on
Set the DIP switches in the
receiver to match the jumper
settings in the transmitter. If they
don’t match, the controller will
not function.
IMPORTANT! Before you change
the jumper settings, make sure
the battery is not connected to
the transmitter. Then change the
position of the jumpers in the
transmitter.
Note: When two or more fans are
located near each other, you may
desire to have the receiver and
transmitter for each fan set to a
different code, so that the operation
of one fan does not affect the
operation of the other fans.
Set the CFL toggle switch
down in the direction that
reads “CFL.” Install the
included 12-volt battery into
the transmitter.
+_
(Shown with transmitter door removed)
10
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Wiring Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
F
R
O
M
R
E
C
E
I
V
E
R
F
R
O
M
R
E
C
E
I
V
E
R
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
B
R
A
C
K
E
T
Using an orange wire
connector from
the hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
green/yellow stripe (grounding)
green/yellow stripe
green/yellow stripe
white black
blue
white (common out) black (fan out) blue (light out)
Using the blue wire
connectors from the remote
control hardware bag,
connect the white wire
from the receiver (marked
“common out”) to the white
wire from fan. Connect the
black wire from the receiver
(marked “fan out”) to the
black wire from the fan.
Connect the blue wire from
the receiver (marked ”light
out”) to the blue wire from
the fan. The red wire from
the receiver will not be used,
it has a pre-installed wire
terminator.
Using an orange wire
connector from
the hardware bag,
connect the black wire
(ungrounded) from the
ceiling to the black wire
from the receiver (marked
“live in”). Connect the
white wire (grounded)
from the ceiling to
the white wire from
the receiver (marked
“neutral in”).
F
R
O
M
F
A
N
F
R
O
M
F
A
N
F
R
O
M
C
E
I
L
I
N
G
black (ungrounded) white (grounded) white (neutral in)
black (live in)
For Dual Switches
For a Single Switch
11
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
12
M3500-01 •11/30/12 • © Hunter Fan Company
Canopy
Lift the canopy into place so that
the screw holes are aligned.
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Screw
Holes
Insert the two canopy screws
found in the hardware bag.
Note: Fan style may vary.

www.HunterFan.com 1.888.830.1326
M3500-01 •11/30/12 • © Hunter Fan Company
Blades
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the nishes.
13
Insert grommets found in the hardware
bag into the holes in the blades, then
secure each blade to a blade iron with
screws found in the hardware bag.
Remember the screws that
you kept after removing the
shipping blocks (page 6)? You
need them for this step.
Lightly attach the blade irons to the
motor with the blade iron armature
screws, then securely tighten after both
screws are attached.

www.HunterFan.com 1.888.830.1326
Auto Balance™
Retaining
Screw
Notch
Auto Balance
If you are using one of the
enclosed downrod assemblies,
it is now time for you to activate
the Auto Balance system by
removing the ve red retaining
screws. Rotate the blades slowly
until one of the red retaining
screws is visible through the notch
in the mounting plate. Remove
the retaining screw from the
bottom of the fan housing using a
screwdriver. Repeat this process for
all 5 retaining screws.
Note: After the retaining screws
are removed, the blades will feel
loose. This is normal, as loose
blades are a characteristic of the
Auto Balance system.
Note: If you are using a downrod
assembly longer than 6 inches,
leave the retaining screws in
their place and continue the
installation process.
14
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Screw two (2) housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Insert the third screw, found in
the hardware bag, into place and then
tighten all three (3) screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing xture falling.
Switch Housing
15
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Light Kit
Partially install two of the switch housing
screws found in the bag. Connect
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Align the notches in the sides of the lower
switch housing with the upper switch
housing screws. Lift the lower switch housing.
Twist the lower switch housing clockwise
to lock into place. Then thread the fan
pull chain through the hole in the light kit.
Install the third switch housing screw.
Tighten all three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
switch housing screws could result in the light xture falling.
Want to install your fan without a light kit?
Go to www.HunterFan.com/FAQs and click
“How do I install my fan without the light kit?”
Switch
Housing
Screw
Notch
Switch
Housing
Screw
16
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Light Kit (continued)
CONGRATULATIONS!
YOU’RE DONE!
See next page for fan
operation instructions.
Note: Globe style and number of
lights may vary.
Connect the appropriate pull
chain pendant to each of the
short chains coming from the
nial and nial cap. The fan pull
chain controls the speed: high,
medium, low, and off. The light
pull chain controls the light
xture: on and off.
Light
Pull
Chain
Fan
Pull
Chain
Press the globe and globe keeper
ush against the metal plate. Thread
the light pull chain through the hole in
the center of the nial cap and thread
the fan pull chain through the hole in
the side of the cap. Finally, thread only
the light pull chain through the hole
in the nial and screw the nial onto
the threaded rod.
Install a light bulb in each socket.
Finial
Finial
Cap
Globe
Keeper
Metal
Plate
Globe
M3500-01 •11/30/12 • © Hunter Fan Company
17

www.HunterFan.com 1.888.830.1326
M3500-01 •11/30/12 • © Hunter Fan Company
18
To turn on fan, press a fan speed
button. Speeds range from off (0) to
high (3). The light button turns the
light on to full brightness. To dim
the light, hold the light button
down until you reach your desired
brightness. Push the light button
again to turn off the light.
To install the transmitter cradle, remove
the two screws holding the switch
cover plate. Do not remove the cover
plate. Orient the cradle by lining up
the two mounting holes with those on
the cover plate. Insert and tighten the
screws. Do not over tighten. Note: For
rocker-style cover plates, break off the
tabs by pushing outward.
Medium
Speed
Light
High
Speed
Install one (1) 12-Volt, type 23A,
MN-21 battery (included) into
the transmitter. Clean the battery
contacts and also those of the
device prior to battery installation.
Ensure the battery is installed
correctly with regard to polarity
(+ and -). Please contact your local
battery recycling center for proper
battery disposal information.
12 V Battery
(Type 23A)
Fan
Off
Low
Speed
+
Operation, Maintenance, & Cleaning
Rocker-
Style
Plate
Switch
Cover
Plate
Removed
Tabs
ON
Turn Power
Note: Remove the battery from
the remote control transmitter if
the product is to remain unused
for an extended period of time.
To remove the battery, remove
the back cover of the remote
control transmitter. Remove used
batteries promptly.

www.HunterFan.com 1.888.830.1326
Changing the direction of air ow -
move the reverse switch to the opposite
position.
Cleaning the fan - use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the nishes.
Reverse
Switch
Changing the bulbs - unscrew the nial
and remove it from the threaded rod.
Remove the nial cap and unscrew the
globe keeper while supporting the globe
with your other hand. Carefully remove
the globe. Unscrew bulbs and replace with
bulbs of same type and wattage. Reinstall
the globe assembly.
Finial
Finial
Cap
Globe
Keeper
Metal
Plate
Globe
Operation, Maintenance, & Cleaning (continued)
19
M3500-01 •11/30/12 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
M3500-01 •11/30/12 • © Hunter Fan Company
20
Troubleshooting
Excessive wobbling
• Tighten all of the blade and
blade iron screws until they
are snug.
• Use the provided balancing
kit and instructions to balance
the fan.
Noisy Operation
• Tighten the blade and blade
iron screws until they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
Remote control of fan is erratic
• Make sure battery is installed
correctly.
• Install a fresh battery.
Fan doesn’t work
• Make sure power switch is on.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
rmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 11.
• Check the plug connection in
the switch housing.
2-YEAR ENERGY STAR LIGHT KIT WARRANTY
The Hunter Fan Company makes the following warranty to the original user or consumer purchaser of each Hunter Energy Efcient
Light Kit:
If your Hunter Energy Efcient Light Kit fails at any time within two years after the date of sale due to a defect in material or
workmanship, labor to repair the defect will be provided free of charge at our nearest service center or our service department in
Memphis, TN. You will be responsible for all labor costs after this two-year period.
This warranty is voided if this product is not purchased in the U.S.A. or Canada.
This warranty excludes and does not cover defects, malfunctions or failures of any product which were caused by repairs by
persons not authorized by us, use of parts or accessories not authorized by us, mishandling, improper installation, modications or
damage to the light xture while in your possession, or unreasonable use, including failure to provide reasonable and necessary
maintenance. IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.