Hunter 72016 User manual

English
Model

Digital Ceramic HeaterDigital Ceramic Heater
With Remote Control

2ZQHU V0DQXDO
g
g
g

2
7$%/(2)&217(176
81614-01 R20200301
Assembly Instructions
8
6
8

3
,1752'8&7,21
Thank you for choosing the Hunter Ceramic Heater. This manual
gives you complete instructions for using your heater.
6$)(7<$1':$51,1*6
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE,
INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL
SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE!
SAVE THESE INSTRUCTIONS FOR REFERENCE.
odors. Make sure that the room in which the appliance is located is well
ventilated during this operation. It is normal for the appliance to emit
small cracking sounds when you turn it on the first time. Do not be
alarmed.
NOTE: When switching on the appliance for the first time, allow it to run
at full power for approximately two hours to remove any manufacturing
When using electrical appliances, basic precautions should always
be followed to reduce the risk of fire, electric shock and injury to
persons or property, including the following:
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. Use handles when moving this heater. Keep
combustible materials, such as furniture, pillows, bedding, papers,
clothes and curtains at least 3' (0.9 m) from the front and top of the
heater and keep them away from the sides and rear. Keep the rear
grille away from walls or drapes so it does not block the air intake.
3. Extreme caution is necessary when any heater is used by or near
children or invalids, and whenever the heater is left operating and
unattended.
4. Always unplug heater when not in use.
5. Do not operate heater with a damaged cord, plug, or after the
heater malfunctions, or has been dropped or damaged in any
manner. Discard heater or return to an authorized service facility for
examination and/or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms, laundry areas
and similar indoor locations. Never locate heater where it may fall
into a bathtub or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will
not be tripped over.
9. To disconnect the heater, turn control to OFF, then remove the plug
from the outlet.
10. Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock, fire or damage
to the heater.
,03257$17,16758&7,216
81614-01 R20200301

4
11. To prevent a possible fire, do not block air intakes or exhaust in
any manner. Do not use on soft surfaces, like a bed, where openings
may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do not use it
in areas where gasoline, paint, or flammable liquids are used or
stored.
13. Use this heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric
shock, injury to persons, or other damage to property.
14. Ensure the heater is on a stable, secure surface to eliminate the
potential of tipping it over.
15. To prevent overload and blown fuses, be sure that no other
appliance is plugged into the same outlet (receptacle) or into another
outlet (receptacle) wired into the same circuit.
16. It is normal for the heater’s plug and cord to feel warm to the
touch. A plug or cord which becomes hot to the touch or becomes
distorted in shape may be a result of a worn electrical outlet. Worn
outlets or receptacles should be replaced prior to further use of the
heater. Plugging heater into a worn outlet/receptacle may result in
overheating of the power cord or fire.
17. Always plug heaters directly into a wall outlet/receptacle. Never
use with an extension cord or relocatable power tap (outlet/power
strip).
18. Check your heater cord and plug connections. A loose fitting
outlet can cause the plug to overheat or cause a fire. Be sure plug fits
tight in the outlet. Check frequently during use to make sure plug and
outlet are not hot. If so, discontinue using heater and have outlet
replaced by a qualified electrician.
19. Note: Heaters draw more current than small appliances,
overheating of the outlet may occur even if it has not occurred with
the other appliances.
20. Check that neither the appliance nor the power cable has been
damaged in any way during transportation.
21. Make sure that no pieces of polystyrene or other packaging
material have been left between elements of the appliance. It may be
necessary to clean the appliance.
22. Connect to properly polarized outlets only.
23. This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit
in a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
DANGER-HIGH TEMPERATURES MAY BE GENERATED
UNDER CERTAIN ABNORMAL CONDITION. DO NOT
PARTIALLY OR FULLY COVER OR OBSTRUCT THE
FRONT OF THIS HEATER.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
81614-01 R20200301

5
3$5762)7+(+($7(5
$66(0%/<,16758&7,216
Parts of the Heater
1.
2. LED Display
3. Safety Grille
4. Base
5. Remote Control
6. Power Light
Control Panel
Symbols
(Figure 2)
Power Button
H/L Heat Button
Oscillation Button
Plus Button
Minus Button
Timer Button
Figure 2
(Figure 1)
Figure 1
5
2
3
1
4
6
Temperature Setting Button
1. Unscrew three (3) locking screws from the bottom of the heater
body (Figure 3) and save them.
2. Align two screw bosses and boss holes on back of two halves
of base according to Figure 4.
3. Press two halves of the base, as in Figure 5, to interlock them
together. (Figure 5)
4. Align power cord to the slot on the top side of the base. (Figure 6)
5. Secure the base to the heater body with the locking screws from
Figure 3. Tighten the locking screws firmly with a screw driver.
(Figure 7)
Figure 3
Fig
ure
3
Figure 6 Figure 7
Figure 4
Screw
Bosses
Boss
Holes
81614-01 R20200301
Figure 5
Figure 6
Figure 7

6
Timer Function (Figure 8)
The timer function may be activated when the heater display is in
any function. This function allows you to set the length of time
the heater will run before turning itself off, from 0 hour to 8 hours.
Pressing the Timer Button
Timer Button
will increase the length of time
by 1 hour each time this button is pressed. After the display
reflects 8 hours, pressing the Timer Button once more will
reset the heater to run continuously. The heater will turn off when
the set time has elapsed. The unit can be turned back on by
pressing the
to 0 hour will cancel the timer function.
Pressing the Power Button .
Oscillation
Pressing the Oscillation Button will allow the heater to
oscillate back and forth. To stop the oscillation, press the
Oscillation Button again.
7. To turn the heater OFF, press the Power Button . The
unit will first turn off the heating elements, the fan will be shut
down 30 seconds later. Unplug the unit by pulling the plug from
the electrical outlet only after the fan stopped.
3. When the heater is initially plugged in, there will be a "beep"
and the Power Light will turn on indicating power to the unit.
The Power Light will remain lit until the heater is unplugged
from the electrical outlet. (Figure 2)
4. Turn the heater ON by pressing the Power Button .
5. When turning the heater on, the unit will be in HIGH heat.
6. Press the button to switch over LOW or HIGH heat.
Figure 8
81614-01 R20200301
1. Place the heater on a firm, level surface, after assembling per
this manual. Plastic or rubber tabs, like the feet on this unit, may
stick to furniture surfaces and/or hardwood floors. The unit may
leave a residue that could darken, stain or leave permanent
blemishes on the finish of certain furniture surfaces, including
wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 volt AC outlet. Be sure that the
plug fits tightly into outlet. When plugs fit loosely into
receptacles, they may slip partially or completely out of the
receptacle with only the slight movement of the attached cord.
Receptacles in this condition may overheat and pose a serious
fire hazard; if covered by a curtain or drape, the fire hazard is
even greater.
Operation

7
2. All the functions performed using the remote control work
identically to the buttons on the control panel, except that there
is no
only can use the and buttons to switch the desired
temperature you want. You cannot change the display to show
the temperature reading between Celsius and Fahrenheit by
pressing and buttons.
Note: Change the batteries with new ones if the remote control
does not operate well. Otherwise your remote control may not
operate properly. Remove the batteries out of the remote control if
you won't use the remote control for a long time. Remaining
batteries may damage your remote control.
Note: Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc), or rechargeable (nickel-cadmium)
batteries.
Battery Disposal - Please dispose of the used battery per
municipal or provincial law.
Figure 11
Remote Control (Figure 11)
1. The remote control uses two (2) "AAA" batteries (not included)
for operation.
4. Once the room temperature reaches 2 degrees above the set
temperature, the heater will shut off. Once the room temperature
reaches 2 degrees below the set temperature, the heater will turn
back on and continue to cycle off and on to maintain the set
temperature.
5. This function will cancel if the button is pressed and the
heater will run continuously.
NOTE: The temperature display does not indicate the temperature
NOTE: It is normal for the heater "fan" to run for approximately 30
of the heated air being emitted by the heater.
You also can press the or buttons on the remote control to
set the room at desired temperature.
seconds when the heater shuts off after reaching the set
temperature.
81614-01 R20200301
Temperature Setting Button on remote control; you
2. Press the and buttons at the same time for two seconds
to change the display to show the temperature reading in Celsius.
Press the same two buttons together again to change the display
back to show the temperature reading in Fahrenheit.
3. When the display shows the temperature at which you want to
set the unit, the set temperature will flash several time. The
display will return to indicate the current room temperature and
will gradually change as the room temperature changes.
1. To set the room at a specific temperature, press the
Temperature Setting Button , then press the or
buttons to the desired temperature. The heater is now in Auto
Temperature Mode and the indicator will glow on the
.
ALED
display
Figure 9
Figure 10
Automatic Temperature Control (Figure 9) (Figure 10)

8
6725$*(
1. Perform the cleaning procedures described above.
2. Wipe all parts dry.
3. Pack the heater in a plastic bag and store it in a cool, dry place.
We recommend that you store the heater in its original carton.
7528%/(6+227,1*
If your heater fails to operate:
Make sure the electrical outlet or circuit breaker is working.
Check for obstructions. If you find an obstruction, turn the
heater OFF, and UNPLUG THE UNIT. Carefully remove the
obstruction and follow the reset instructions.
0$,17(1$1&(
1. Press the Power Button to turn the heater OFF and unplug
the heater before moving or cleaning.
2. Interior dust can often be removed by using a vacuum cleaner
with a crevice tool attachment.
3. To clean the enclosure, use a clean, soft and lightly damp
cloth to gently wipe off the dirt from the surface of the unit. Be
sure not to wet the heating element and the switches. Allow the
unit to dry completely before use.
4. Do not use cleaning liquid or other chemicals to spray on the
unit.
this occurs, the heater can only resume its normal operation after
resetting it. To reset the heater:
2. Unplug the heater and wait 10 minutes for the unit to cool down.
1. Turn the Power Control to OFF position.
3. After the 10 minutes, plug the unit in again and operate normally.
81614-01 R20200301
This heater is equipped with a safety tip-over switch. This feature
cuts the main power to the heater if it gets knocked over. If the
heater tips over, simply stand it upright and press the Power
Button to resume operation.
This heater includes an Overheat Protection System that shuts
the unit off when a potential overheat temperature is reached. If

9
Warranty
)&&:$51,1*
FCC WARNING:
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
NOTE :
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
:$55$17<
Hunter Home Comfort makes the following limited warranty to the
user or consumer purchaser of this Hunter heater:
If your Hunter heater motor fails at any time within three years
Hunter Home Comfort
1831-A West Oak Parkway, Marietta, GA 30062
1-888-880-3267
81614-01 R20200301
If you need any assistance with setup, operation, or parts for your
new Hunter Heater, please call us. Our technical support staff is
ready to help! We are open 24 hours a day, 7 days a week.
1-888-880-3267 (FANS)
You may also reach us online at www.HunterHomeComfort.com.
[email protected]
An electronic copy of this user manual can also be obtained online
at www.HunterHomeComfort.com.
after the date of sale to you due to a defect in material or
workmanship, labor to repair the defect will be provided free of
charge at our nearest service center or our Service Department
in Marietta, Georgia. You will be responsible for labor costs after
this three years period. The foregoing limited warranty applies
only to the motor itself, and does not apply to electronic controls
such as remote controls, remote control receivers or transmitters
used in conjunction with the motor. These electronic control items
are included in the one year limited warranty below.

10
Warranty
81614-01 R20200301
IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN
RESPECT TO THE GLASS GLOBES OR LIGHT BULBS OR THE
FINISH ON ANY METAL PORTION OF THE HEATER. THIS
WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, IN RESPECT TO ANY HUNTER HEATER MOTOR
OR OTHER HEATER PART, IS EXPRESSLY LIMITED TO THE
PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE
FOR SUCH MOTORS AND OTHER PARTS.
This warranty is voided if your Hunter heater is not purchased and
used in the USA.
This warranty excludes and does not cover defects, malfunctions
or failures of any Hunter heater which were caused by repairs by
persons not authorized by us, use of parts or accessories not
authorized by us, mishandling, improper installation, modifications,
or damage to the Hunter heater while in your possession, or
unreasonable use, including failure to provide reasonable and
necessary maintenance.
To obtain servicing, contact the nearest Hunter authorized service
center or the Hunter Home Comfort Service Department, 1831-A
West Oak Parkway, Marietta, GA 30062. Please contact us before
shipping your heater to us. If we authorize you to ship it to us, you
will be responsible for all insurance and freight or other
transportation charges to our factory service center. We will return
your Hunter heater freight prepaid. Your heater should be properly
packed to avoid damage in transit since we will not be responsible
for any such damage. Proof of purchase is required when
requesting warranty service. The purchaser must present sales
receipt or other document that establishes proof of purchase.
in material or workmanship, we will repair or, at our option,
replace the defective part free of charge for parts and labor
performed at our nearest service center or at our Service
Department in Marietta, Georgia.
IF THE USER OR CONSUMER PURCHASER CEASES TO
OWN THE HEATER, THIS WARRANTY AND ANY IMPLIED
WARRANTY WHICH THEN REMAINS IN EFFECT, INCLUDING
BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE VOIDED. NO WARRANTY, EXPRESSED OR
If any part of your Hunter heater other than the motor fails at any
time within one year after the date of sale to you due to a defect
IN NO EVENT SHALL HUNTER HOME COMFORT BE LIABLE
FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
1831-A West Oak Parkway, Marietta, GA 30062
Hunter is a trademark of the Hunter Fan Company and
is used under license to Hunter Home Comfort.
Printed in China