Hunter BTT-101 User manual

BTT
Battery-Operated
Bluetooth Tap Timer
Quick Start Guide
ENGLISH
Please read and keep all safety and use instructions. For more
information, visit hunterindustries.com/BTT.
Important Safety Instructions
1. Only use attachments/accessories specied by the manufacturer.
2. Use a Hose Vacuum Breaker where required to prevent backow to the
water supply.
3. Use a pressure regulator where required to control the output of
water. (Model No. PRLG203FH3MH for 20 PSI (1.4 bar/138 kPa),
PRLG253FH3MH for 25 PSI (1.7 bar/172 kPa), PRLG303FH3MH for 30
PSI (2 bar/207 kPa), PRLG403FH3MH for 40 PSI (2.8 bar/276 kPa))
Warnings and Cautions
• Do NOT make unauthorized alterations to this product.
• Keep the product away from re and heat sources.
• Do not expose products containing batteries to excessive heat (e.g.,
from storage in direct sunlight, re, or the like).
• The product label is located on the back of the product.
• Replace only with same or equivalent battery type. Dispose of used
batteries according to instructions.
• Do NOT mix old and new batteries, or mix dierent types or makes
of batteries.
Connecting the Batteries
1. Squeeze the battery compartment tabs
with two ngers to withdraw the battery
compartment.
2. Insert the included 2x AA standard alkaline
batteries into the terminals. Observe +
position.
3. Replace the battery compartment.
4. Test power to the controller by pressing the
manual button on the front of the controller
and listen for a click sound. Press again to
turn o. NOTE: Manual button mode runs for a
maximum 60 minutes and then shuts
o watering.
Connecting to Water Supply
BTT-100/200 Instructions:
1. Connect the controller only to a standard
¾" (19 mm) threaded water supply/hose
faucet outlet.
2. Hand-tighten until secure.
3. Connect a ¾" (19 mm) inlet hose or drip
adapter (Model No. BTT-LOC) to the
BTT outlet.
4. Hand-tighten until secure.
Connecting to Water Supply BTT-101/201 Instructions:
1. Connect the controller only to a standard ¾" (19 mm) threaded water
supply/hose faucet outlet. Unscrew the grey adapter to use the
1" (25 mm) BSP inlet option.
2. Hand-tighten until secure.
3. Connect a ¾" (19 mm) inlet hose, drip adapter (Model No. BTT-LOC)
or quick connect adapter (included) to the BTT outlet.
4. Hand-tighten until secure.
Download Mobile App
1. Download the free Hunter BTT app to a
smartphone device from the App Store
for iOS devices, or Google Play™ store
for Android™ devices.
• iOS Compatibility: Requires
iOS 9.0 or later. Compatible
with iPhone.
• Android Compatibility:
Requires Android 4.4 or
above.
2. Be within 32' (10 m) of the controller.
3. Turn on Bluetooth on the smartphone device.
4. Press the SCAN button and select Hunter BTT.
Timer Mode Programming
Timer mode allows for watering at four
dierent start times from 1 second to 6
hours,
per watering day.
1. Pre Schedule and select the Timer
tab.
2. Water Days: Select the desired water
days. Save and Conrm.
3. Start Times: Set START TIME 1 and
optional START TIME 2-4. Save and
Conrm.
4. Run Time: Set the desired RUN TIME
from 1 second to 6 hours. Save and
Conrm.
Cycling Mode Programming
Cycling mode allows the Run Time to repeat
continually aer the scheduled interval
(Soak Time) from a Start Time to an End Time.
1. Press Schedule and select the Cycling
tab.
2. Water Days: Select the desired water
days. Save and Conrm.
3. Start Times: Set START TIME 1 and
optional START TIME 2. Save and
Conrm.
4. End Times: Set END TIME 1 and optional
END TIME 2. Save and Conrm.
5. Run Time: Set the desired RUN TIME
from
1 second to 24 hours. Save and Conrm.
6. Soak Time: Set optional SOAK TIME, the
time between each Run Time interval,
from 1
second to 24 hours. Save and Conrm.
Manual Watering
1. For manual watering, press Schedule
, press the Play button, select a zone
or Run All. Enter a runtime up to 360
minutes and press Run.
2. Set Manual Start Button Run Time: In
controller settings under zones, select
zone(s), set run time from 1 to 60
minutes. Save and Conrm.
Additional Settings
1. Renaming your BTT: Press More ,
select controller, select controller and
serial number and enter a name in
Nickname section. Save and Conrm.
2. Creating a Passcode: In controller
settings, enter a 4-digit code in the
Create a Passcode section. To disable, press Disable Passcode.
Save and Conrm.
3. Changing the Language: Press More , select App Settings,
Manual Button
Low-Battery Indicator
Manual Buttons
Low-Battery Indicator

then Language. Select the desired language. Save and Conrm.
4. Suspend Watering: In controller settings under Advaced, select
Suspend. Set from 1-99 days. Save and Conrm.
5. Zone O Mode: In controller settings under zones, select the zone
then select the toggle to turn o watering.
Troubleshooting
Problem Solution
Controller not appearing
in scan list
Loses connection
Can’t connect or
app errors
Move closer than 32' (10 m) of controller
Verify battery strength and cycle the
batteries. Uninstall and reinstall Hunter
BTT app. Accept permissions: “Location
Tracking” or manually enable permissions in
smartphone settings. Reboot smartphone.
Reset phone network settings. Reconnect
controller.
Manual button press not
responding
Replace the batteries (two AA alkaline
batteries).
App indicates watering,
but none is occurring
Turn on water supply. Repeat manual
watering within the app or on controller.
Automatic irrigation
does not start at start
time
Verify controller is programmed for
automatic watering; correct Start Times, Run
Time and Watering Days.
Controller waters more
than one time
Eliminate controller start times as needed.
Correct the Soak Time in Cycling mode.
Incorrect passcode Remove and replace batteries. Go back to
the app and connect.
FCC Notice
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the manufacturer’s
instruction manual, may cause interference with radio and television
reception. This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Notice: The FCC regulations provide that changes or modications not
expressly approved by Hunter Industries Inc. could void your authority to
operate this equipment. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
with radio or television reception, which can be determined by turning
the equipment o and on, you are encouraged to try to correct the
interference by one or more of the following measures:
• Reorient the receiving antenna.
• Relocate the system with respect to the receiver.
• Move the system away from the receiver.
• Plug the system into a dierent outlet so that the system
and the receiver are on dierent branch circuits.
• Consult the dealer or an experienced radio/TV technician
for help.
If necessary, consult a representative of Hunter Industries Inc. or an
experienced radio/television technician for additional suggestions.
Changes or modications not expressly approved by Hunter Industries
could void the user’s authority to operate this device.
Bluetooth Information
1. Frequency band of operation: 2400 MHz to 2480 MHz.
2. Bluetooth: Maximum transit power less than 20 dBm EIRP
Bluetooth Low Energy: Maximum power spectral density less
than 10 dBm/MHz EIRP.
Industry Canada Notice
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
http://hunter.direct/btthelp
CE Notice
Hunter Industries hereby declares that this product is in compliance
with the essential requirements and other relevant provisions of
Directive 2014/53/EU and all other EU directive requirements.
This symbol means the product must not be discarded as
household waste, and should be delivered to an appropriate collection
facility for recycling. Proper disposal and recycling helps protect
natural resources, human health, and the environment. For more
information on disposal and recycling of this product, contact your
local municipality, disposal service, or the shop where you bought this
product. Please dispose of used batteries properly, following local
regulations. Do NOT incinerate.
Management Regulation for Low-power Radio-frequency Devices
Article XII
According to “Management Regulation for Low-power Radio-
frequency Devices” without permission granted by the NCC, any
company, enterprise, or user is not allowed to change frequency,
enhance transmitting power or alter original characteristic as well as
performance to approved low-power radio frequency devices.
Article XIV
The low-power radio-frequency devices shall not inuence aircra
security and interfere legal communications; if found, the user shall
cease operating immediately until no interference is achieved. The
said legal communications means radio communications operated in
compliance with the Telecommunications Act.
Equipment Protection
• Water pressure requirements: Make sure your water pressure
is 7-116 PSI (0.5-8 bar/50-800 kPa).
• Make sure water is clean and particle-free.
• Maximum inlet water temperature: 100°F (38°C)
• Operating temperature: 41°F to 140°F (5°C to 60°C)
• Protect against freezing: Do not allow water to freeze in the
Tap Timer or in any connected hose.
• Chemicals: Do not use the Tap Timer with or to dispense
any chemicals of any kind.
• Do not open: The Tap Timer requires no maintenance and
contains no user-serviceable parts.
• Periodic inspection of connections is recommended to
prevent water leaks.
• Approvals: IPX6
The Bluetooth word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Hunter Industries Corporation
is under license. IOS is a trademark or registered trademark of Cisco in the
U.S. and other countries and is used under license. Apple, the Apple logo, and
iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
App Store is a service mark of Apple Inc. Google, the Google logo, Google Play,
and Android are trademarks of Google LLC.
© 2019 Hunter Industries Inc. Hunter and the Hunter logo are trademarks of
Hunter Industries, registered in the U.S. and other countries.
hunterindustries.com RC-074-QG-BTT EM 6/19