HunterDouglas MOTOLUX TURNILS 802142000 Installation manual

35mm RF Electronic Limit 240V Molex
802142000 (MT35E-6-28-240/50)
Programming
Instructions

Programming Instructions
35mm RF Electronic Limit 240V Molex - 802142000 (MT35E-6-28-240/50)
Programming Button
You will notice that there are 2 yellow buttons on the head of the motor, these buttons are used for pairing the remote and
resetting the motor.
You will need something small enough to put in the both the hole in the head of the motor and in the Programming button on
the remote control, a Paper Clip or Jewellers Screwdriver is perfect.
To Pair the Motor and a Remote / Channel
(To be performed within 10 seconds)
1. Using a paperclip or similar, press and hold the programming button in the head of the motor for more than three seconds to
wake the motor up. The motor will jog.
2. Select the channel required on the remote.
3. Press briefly the UP (top) button within 10 seconds.
4. The motor will jog.
To Change the Rotation Direction
(To be performed within 10 seconds)
1. If the direction is correct, there is no action required, move to limit setting.
2. If direction is wrong, press the STOP (middle) button of the programmed remote/channel for 7 seconds. The motor will jog.
3. Press briefly the DOWN (bottom) button within 10 seconds. The motor will jog.
4. Test the blind and the direction should be ok.
Limit Setting: TOP LIMIT FIRST
The Motor might be in step by step mode - this will go to conitinous movement after the limits are set.
(To be performed within 30 seconds, if nothing is performed after 30 seconds the motor will exit limit setting function)
1. Press and hold the Programming button on the side of the remote with a paper clip until you get a jiggle.
2. Move the blind to where you would like the Top Limit to be.
3. Push and hold the Programming button on the side of the remote, you will get a jiggle.
4. Move the blind to where you would like the Bottom Limit to be.
5. Push and hold the Programming button on the side of the remote, you will get a jiggle.
6. Next, (very important) Push and hold the Programming button on the side of the remote, you will get a jiggle.
7. Limits have now been recorded, please test the blind.
The above will need to be done for each different motor on each different channel.
Resetting a Motor Back to Factory
1. On the motor, press the program button for more than SEVEN seconds.
Note: The motor will jog twice, keep the button depressed until the second jog after 7 secs.
2. Once reset, the motor will do a double jog.
To Add Multiple Blinds to a Group Channel
Example: Putting 5 blinds all on Channel Six.
1. On the Remote go to Blind 1 on Channel 1 – Push and Hold the Stop Button until you get a jiggle. Now go to Channel 6 and push
and hold the Up Button you will get a Jiggle. Blind 1 is now added to Channel 6.
2. On the Remote go to Blind 2 on Channel 2 – Push and Hold the Stop Button until you get a jiggle. Now go to Channel 6 and push
and hold the Up Button you will get a jiggle. Blind 2 is now added to Channel 6.
Repeat these steps until you have moved all blinds over to channel 6.
This feature can also be used to transfer motors onto other Remote Controls.
Left Motor Right Motor
Programming Button

Programming Instructions
35mm RF Electronic Limit 240V Molex - 802142000 (MT35E-6-28-240/50)
Additional Features
The above are simple programming steps but there are more functions this motor can perform.
Intermediate Limits:
Other than the Top and Bottom Limits this motor can store an additional four Intermediate Limits.
To Set Intermediate Limits:
1. After setting the top and bottom limits and exiting the program mode, move the blind to where you would like an intermediate
limit set.
2. Press the programming button on the side of the remote until you get a jiggle now press the programming button on the side of
the remote a second time, you will get a jiggle.
3. An intermediate limit has now been set.
When operating the blind if you do not want to stop at the intermediate limit:
1. Press the button for the direction that you would like the blind to move in.
2. Once the blind starts moving, press the same button a second time and it will skip that limit and continue onto the furthest limit.
Adjusting a Limit after it has been set:
1. Move the blind to the limit that you wish to adjust.
2. Press the Programming button on the side of the remote until you get a jiggle, now move the blind to the new limit position
and press Programming button on the side of the remote.
3. The blind will jiggle and the limit has been adjusted.
To delete an Intermediate Limit or Bottom Limit:
(Top limit cannot be deleted in this manner)
To Delete Top Limit, see Resetting a Motor Back to Factory
1. Move to the limit that you wish to delete.
2. Push the Programming button on the side of the remote and keeping the button pushed in, the blind will jiggle once and
then a second time approximately 5 seconds later indicating that the limit has been deleted.
To ADD a New Remote or Channel
1. Using a remote or channel ALREADY PROGRAMMED to the motor, wake the motor up by pressing and holding the STOP (middle)
button for more than three seconds. The motor will jog.
2. Press briefly the UP button on the NEW remote/channel within 10 seconds. The motor will jog.
To DELETE A New Remote or Channel
1. On the remote or channel to be deleted, wake the motor up by pressing and holding the STOP (middle) button for more
than 3 seconds. The motor will jog.
2. Using a paperclip or similar, within 10 seconds, press and hold the programming button on the back of the remote control
for 3 seconds. The motor will jog.
To Switch from Automatic Movement to Manual Movement (or Vice Versa)
1. Wake the motor up by pressing the STOP (middle) button for 5 seconds. The motor will jog.
2. Within 10 seconds, press the STOP button briefly. The motor will jog.
Removing a blind from an already paired channel.
Option 1: If you already have a group of motors on a particular channel and want to remove one motor only, reset the motor needing
to be moved, then restart the process of pairing and allocating the motor to the correct channel.
Option 2: If it is only one motor on a channel, follow the ‘Delete Channel’ instructions and set up and start again.
Optional Dry Contact Control or Serial RS485/232
Connection Requirements
RF Remote Operation
White: Serial A
Black: Common
Red: Up
Green: Stop
Yellow: Down
Blue: Serial B
Serial = RS485/232
©Copyright 2023 Hunter Douglas Limited ABN 98 009 675 709 ®Motolux is a registered trade mark of Hunter Douglas Limited 12/2023