Hurricane 736503 User manual

16” OSCILLATING
WALL MOUNT FAN
OWNER’S MANUAL
NOTE: Pictures in manual are for reference only.
Product No: #736503
READ AND SAVE THESE INSTRUCTIONS

COMPONENTS
MOTOR
MOTOR SHAFT
REAR GUARD
PVC TUBE
BLADE SPINNER
PLASTIC NUT
FRONT GUARD
Read and follow all instructions before operating fan. DO NOT use fan if any
parts are damaged or missing.
CAUTION
1. This appliance is not intended for use by young children without supervision.
2. This appliance has a polarized plug (one blade is wider than the other).
To reduce the risk of electrical shock, this plug is intended to fit in a
polarized outlet only. If the plug does not fit fully into the outlet,
reverse the plug. If the plug still does not fit, contact a qualified electrician.
Do not attempt to bypass this safety feature.
3. If the power cord is damaged, it must be replaced by manufacturer.
4. To reduce the risk of fire or electrical shock, DO NOT use this fan with any
solid state speed control device.
5. Changes or modifications to this unit will void the user’s warranty.
WARNING
1. Never insert any object through the housing when the fan is running.
2. Disconnect power when moving fan from one location to another.
3. Disconnect power when removing fan grilles for cleaning.
4. Be sure the fan is on a stable, flat surface when in operation.
5. Important cord and plug information:
(A) This product uses overload protection (fuse). A blown fuse indicates
an overload or short-circuit situation. If the fuse burns out, unplug
the product from the outlet. Replace the fuse by referencing the
instructions (follow product marking for proper fuse rating) and
test the product. If the replacement fuse blows, a short-circuit may
be present and the product should be discarded or returned to an
authorized retail store for examination, repair, and/or replacement.
(B) DO NOT operate any fan with a damaged cord or plug. Discard or
return the fan to an authorized retail store.
(C) DO NOT run power cord under carpeting. DO NOT cover cord with
throw rugs, runners, or similar coverings. DO NOT route cord under
furniture or appliances.
RULES FOR SAFE OPERATION

The fan should be installed on solid wood or a pillar that is secured
perpendicular to the floor.
CAUTION: To prevent the fan from falling off, do not install it on walls less
then 4 inches thick or those made from materials that are easily damaged.
INSTALLING THE MOUNTING BRACKET
Fix the supplied mounting bracket firmly to the wall using the three screws.
NOTE: The bracket
should be positioned
at least 14 inches from
the ceiling and at
least 12 inches from
adjoining wall.
INSTALLING THE STAND
Mount the stand on the bracket by inserting
the bracket catch into the slot on the stand.
INSTALLATION
GUARD & FAN BLADE ASSEMBLY
Follow these assembly instructions carefully.
1. Unscrew the spinner clockwise (or take the spinner out of the bag).
Then unscrew the plastic nut counter-clockwise and remove. Fix the
rear guard to the motor, then tighten the plastic nut again. (Fig. 1)
2. Discard PVC sleeve on shaft. Insert the blade into shaft, and make sure
the rotor shaft pin is fitted into the groove of the blade. Turn the
spinner counter-clockwise to tighten the blade. (Fig. 2)
3. Fasten the front guard and the rear guard using the guard clip. (Fig. 3)
14 inches
12 inches
Ceiling
Wall
Fig. 1 Fig. 2 Fig. 3
Clip
Spinner Tight
Slot
Retaining
Pin
Blade
Spinner
Tight
Loose
Plastic Nut
Stand
Screws
Mounting
Bracket
Slot on
Rear Side
Slot on Rear Side
Mounting
Bracket
Stand

SPEED ADJUSTMENT
Set desired speed by pulling the pull switch (A).
0---Stop 1---Low 2---Medium 3---High
OSCILLATION CONTROL
Adjust the angle of oscillation by pulling the pull
switch (B). Then, push the guard lightly up or down
to reach the desired position.
USER-SERVICING INSTRUCTIONS
1. Grasp the plug and remove it from the
receptacle or other outlet device.
DO NOT unplug by pulling on the cord.
2. Open the fuse cover. Slide open the fuse
access cover on top of the attachment
plug, toward the blades.
3. Remove the fuse carefully. Push the fuse from the other side or turn the
fuse holder over to remove the fuse.
4. Warning: Using the wrong voltage fuse can lead to risk of fire. Replace
the fuse only with a 2.5 A, 125 volt fuse.
5. Close the fuse cover. Slide the fuse access cover on top of the attachment
plug to the closed position.
6. Warning: risk of fire. DO NOT replace attachment plug. Contains a
safety device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
1. Be sure to unplug from the power source before cleaning.
2. Plastic parts should be cleaned with mild soap and damp cloth or sponge.
Thoroughly remove soap film with clean water.
3. Be sure not to let water or other liquid enter the inside of the motor.
CLEANING
(A)
(B)
Manufactured for Hawthorne Hydroponics LLC, a
subsidiary of The Hawthorne Gardening Company,
3204 NW 38th Circle, Vancouver, WA 98660
HawthorneGC.com | Canada: HawthorneGC.ca
©2019. World rights reserved.
16” OSCILLATING WALL MOUNT FAN
Product No: #736503