Hurricane Supreme Series User manual

18" Oscillating
Wall Mount Fan
Instructions
MAINTENANCE AND STORAGE
• Clean fan body and fan blade to avoid
discoloration.
• Use a non-abrasive detergent and soft cloth
for cleaning.
• DO NOT immerse the fan in water, and never
allow water to drip into the motor housing.
• DO NOT use a gasoline thinner or other
chemicals to clean fan.
• For storage, clean fan carefully as instructed
and store in it’s original box. Store fan in a
clean, dry place.
TROUBLESHOOTING
PROBLEM SOLUTION
Fan blade does not rotate • Check to see if plug is inserted into outlet
after the fan has been started. • Make sure fan blade is unobstructed and
is not touching fan screen
There is an abnormal sound • Make sure fan blade is inserted on the
when starting the fan. motor shaft properly and is properly
seated on the rotor pin.
• Make sure fan blade is not hitting fan
guard.
• Check to see if there are burrs on the fan
blade.
CAUTION: Do not use fan if power cord is damaged. Contact service center for
repair instructions.
Use a “QR Code App” on
your smart phone to access
our website and browse our
entire product offering or go
to: www.hurricane-fans.com
www.hurricane-fans.com
™
www.hurricane-fans.com
™
Supreme Series
D
E
L
A
S
E
R
I
E
S
U
P
R
E
M
O

1
2
6
8
9
7
10
11
3
4
5
12 13 14 15 16
17
18
19 20
21
COMPONENTS
ASSEMBLY
Follow these assembly instructions carefully.
1. Rear guard assembly
• Turn blade cap clockwise and remove. Turn guard
lock counterclockwise and remove.
• Install the rear guard by aligning it with the
three posts on the front motor cover.
• Secure rear guard with the guard lock.
2. Fan blade assembly
• Slide fan blade onto motor shaft. Rotate fan
blade down onto the shaft stop.
• Rotate blade cap counterclockwise onto motor
shaft to attach fan blade securely.
3. Front Guard assembly
• Align front guard onto rear guard. Slide guard
ring onto both the front guard and rear guard.
• Tighten guard clip screw into guard ring to secure
the front guard and Rear guard together.
4. Hanging Iron installation
• Find where the stud is in the wall and
drill holes.
• Fasten the hanging iron securely to the
wall with the supplied screws.
• NOTE: For cement walls, please contact
your local hardware store for an
appropriate fastener.
5. Fan installation
• Hang fan on wall by sliding metal
hanger on the back of the fan down
onto hanging iron.
HOW TO REMOVE FRONT GUARD
• Loosen guard clip screw.
• Carefully pull off guard ring and front guard
to access fan blade.
OPERATING FEATURES
This fan has 3 fan speeds The fan can be angled up
or down incrementally.
12 Guard lock
13 Fan blade
14 Blade cap
15 Guard ring
1 Telescopic tube
2 Rear motor cover
3 Front motor cover
4 Motor shaft
5 Rotor pin
6 Swivel screw
7 Leg
8 Base cover
9 Speed switch pull
10 3-speed dial
11 Rear guard
16 Front guard
17 Guard clip
18 Guard clip screw
19 Hanging iron
20 Hanging iron screw
21 Stud
Push down telescopic tube for oscillation.
Pull up telescopic tube to stop oscillation.
SPECIAL PRECAUTIONS
Make sure the
outlet voltage
complies with
specifications
on the fan.
Do not bend or pull power cord with
force. Check power plug and cord for
damage
before using.
To avoid shock,
make sure hands
are dry before
unplugging or
plugging in the
power plug.
Do not use fan
before it has
been completely
assembled.
Do not place fan in
contact with curtains
or where fan can not
work properly.
Do not use fan in an
environment with a
temperature of more
than 104˚F. Fan may overheat
and fail to work properly.
Do not leave children unattended
with fan and don not allow fan to
blow directly on anyone for too long.
Do not spray insecticide, any
type of resin or paint into fan
as it will result in damage.