HUSH Comfort Plus User manual

Comfort Plus Baby Monitor
Instruction manual
Hush Comfort plus.indd 1 7/12/11 20:35:50

2
Baby Monitor
Thank you for purchasing this baby monitor. Please read the
instructions and warnings carefully before use to ensure the safe and
satisfactory operation of this product.
Important safety information . . . 3
Your baby monitor . . . . . . . . . . . 4
Instructions for use. . . . . . . . . . . 5
Check the package contents. . 5
Setting up the parent unit . . . . 5
Setting up the baby unit . . . . . 6
Volume...................6
Using your baby monitor .......7
Batterylow...............7
Language.................7
Setting the clock . . . . . . . . . . . 7
Babyalert ................8
Lullaby...................9
Temperature . . . . . . . . . . . . . 10
Centigrade to Fahrenheit . . . 11
Parent to parent paging. . . . . 11
Talk to your baby . . . . . . . . . 11
Night-light . . . . . . . . . . . . . . . 12
Baby feed timer . . . . . . . . . . . 12
Feedalarm...............13
Sound sensitivity . . . . . . . . . . 14
Lowpower..............14
Simple solutions . . . . . . . . . . . . 15
Helpdesk..................15
General information . . . . . . . . . 16
Changing the batteries . . . . . 16
Guarantee...............17
Weee Directive . . . . . . . . . . . 17
Contents
Hush Comfort plus.indd 2 7/12/11 20:35:51

3
Keep the product and all its
parts out of reach of small
children.
Batteries are small objects.
Replacement of the batteries
must be done by adults.
Keep it dry. Avoid exposure
to precipitation, humidity and
liquids which could all affect
the product circuitry.
Do NOT leave it in high
temperatures as electronic
devices and plastic parts may
warp in heat.
Do NOT leave it in low
temperatures as moisture can
form inside the product, which
may damage the circuit board.
Do NOT use harsh
chemicals, cleaning solvents
or detergents to clean the
product. Wipe with a damp
(not wet) soft cloth to clean.
•
•
•
•
•
•
Do NOT attempt to open
the product. Unauthorised
handling of the device may
damage it and will void your
warranty.
Only use the power supply
that came with the product.
Using an unauthorised
power supply will invalidate
your guarantee and may
irrecoverably damage the
product.
Radio signals transmitted
between the Parent and Baby
unit may cause interference to
hearing aids.
Do NOT use your baby
monitor near emergency/
intensive care medical
equipment, if you have a
pacemaker fitted or during an
electrical storm.
•
•
•
•
Important safety information
Your baby monitor should be treated with care. The information below
has been provided in the interest of safety and will help you to enjoy
this product and the benefits it brings for many years.
Use of this equipment is no substitute for personal attention and
supervision of a child.
Hush Comfort plus.indd 3 7/12/11 20:35:51

4
Your baby monitor
Power on/off
Press and release to power on
Press and hold to power off
Page
Press and hold for
2 seconds to ‘Page’
the Parent unit
Night-light
Microphone
Battery compartment for non-
rechargeable batteries (not supplied)
Display Link light
Noise indication light
OK
Talk
Volume up/Move up
(in the menu)
Menu
Microphone
Speaker
Volume down/Move down
(in the menu)
Power on/off
Press and release to power on
Press and hold to power off
Power on/off light
Flashes when the batteries
are charging
Mains adaptor socket
(underneath)
Low power switch
(underneath)
Temperature
sensor
Hush Comfort plus.indd 4 7/12/11 20:35:55

5
Instructions for use
Check the package
contents
The package contains:
1 Parent unit (receiver) with
belt clip
1 charger pod with fixed
mains adaptor
2 x 800mAh NiMH
rechargeable batteries
1 Baby unit (sender)
1 mains adaptor
1 travel bag
1 instruction manual
Setting up
At the parent unit
1. Remove the belp clip by pulling
downwards.
2.Remove the battery cover on
the back of the parent unit.
3. Insert the 2 x AAA Nickel
Metal Hydride rechargeable
batteries provided, taking care to
note the ‘+’ and ‘-’ markings and
position the batteries the correct
way around. Replace the battery
cover.
•
•
•
•
•
•
•
4. Replace the belt clip by sliding
into place until it clicks home.
5. Plug the charger pod mains
adaptor into a mains power
socket and switch on.
6. Place the parent unit in the
charger pod and charge for a
minimum of 13 hours before first
use or if it has not been used for a
long time.
The red power light on the parent
unit will flash when the batteries
are charging.
Note: The parent unit cannot
be used without rechargeable
batteries, even if it is placed in the
charger.
7. Press and release the ‘Power’
button on the front of the parent
unit to switch it on.
Hush Comfort plus.indd 5 7/12/11 20:35:55

6
Setting up
At the baby unit
1. Your baby unit does not require
batteries to function but we
recommend that you install them.
Should there be a power cut,
your baby unit can then switch to
the back up (non-rechargeable)
battery power.
2. Remove the battery cover on
the back of the baby unit with a
crosshead screwdriver. Insert 4 x
AAA alkaline batteries, taking care
to note the ‘+’ and ‘-’ markings
and position the batteries the
correct way around. Replace the
battery cover and re-tighten using
the crosshead screwdriver.
Note: Do NOT use rechargeable
batteries in the baby unit.
3. Connect the power lead to the
bottom of the baby unit and plug
the mains adaptor into a mains
power socket and switch on.
4. Press and release the ‘Power’
button to switch on.
Note: The baby unit should be
placed about 1 m to 1.5 m away
from the baby’s cot or playpen on
a flat and stable surface. Never
place the baby unit inside the cot,
bed or playpen. Make sure the
unit, cords and mains adaptor
are out of reach of the baby and
other young children.
Never place either the parent or
baby unit on antique or polished
surfaces.
When you have set up your baby
monitor, you will be able to hear
the sounds in your baby’s room
through the speaker on the parent
unit.The green noise indication
light will also flash with the sound
volume level.
Note: If the connection between
the parent and baby unit is broken
at any time, the ‘Link’ light on
the parent unit will flash, the
parent unit will beep and the
green noise indication light will
no longer react to any sounds. To
re-establish the link, please refer
to page 15.
Volume
You can adjust the volume of the
sounds that you can hear through
the parent unit by using the up
and down buttons on the front
of the parent unit.This will not
affect the sensitivity of your baby
monitor, only the volume of the
sounds that you can hear.
Hush Comfort plus.indd 6 7/12/11 20:35:56

7
Battery charge indicator
and battery low warning
The parent unit can operate for
a maximum of 10 hours when it
is out of the charger pod but this
depends on the level of charge
in the batteries and if any of the
other parent unit functions have
been used such as the ‘Talk’ feature.
The battery charge level is indicated
by the battery icon on the parent
unit display. If the battery level is
low, the battery icon will begin to
flash and you will hear a warning
‘beep’. You should return your
parent unit to the charger pod to
re-charge the batteries. You can
still use your parent unit whilst it is
charging in the charger pod. (Check
that the red charging light is flashing
when your parent unit is in the
charger pod).
Language
Your baby monitor can display
information in several different
languages.
To change the display language:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
on the front of the parent unit
until ‘Language’ is displayed.
Press the ‘OK’ button.
2. Use the ‘Up/Down’ buttons to
scroll to your chosen language and
press the ‘OK’ button to confirm.
‘Saved’ will be displayed briefly.
Your chosen language will now be
set.
Clock
The parent unit can display the
current date and time in either 12
or 24 hour clock (the default setting
is 24 hour clock). You will need to
set the clock before you can use
the baby feed timer feature.
To set the time:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Clock’. Press the
‘OK’ button.
2. ‘Set time’ is displayed. Press
the ‘OK’ button.
3. ‘Year’ is displayed. Use the
‘Up/Down’ buttons to scroll to
the correct year. Press the ‘OK’
button.
4. ‘Month’ is displayed. Use the
‘Up/Down’ buttons to scroll to
the correct month. Press the ‘OK’
buttons.
5. ‘Day’ is displayed. Use the
‘Up/Down’ buttons to scroll to
the correct day. Press the ‘OK’
button.
Using your baby monitor
Hush Comfort plus.indd 7 7/12/11 20:35:56

8
6. ‘Hour’ is displayed. Use the
‘Up/Down’ buttons to scroll to
the correct hour. Press the ‘OK’
button.
7. ‘Minute’ is displayed. Use the
‘Up/Down’ buttons to scroll to
the correct minute. Press the
‘OK’ button. You will hear a
confirmation ‘beep’ and ‘Saved’ will
be briefly displayed. The time and
date will now be displayed on the
parent unit.
To set 12 or 24 hour clock:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Clock’. Press the
‘OK’ button.
2. Use the ‘Up/Down’ buttons to
scroll to ‘Hour Format’. Press
the ‘OK’ button.
3. ‘12Hrs?’ will be displayed when
24 hour clock is already set. Press
the ‘OK’ button to change to 12
hour clock or the ‘Menu’ button
to exit without changing the
setting.
If 12 hour clock is set,‘24Hrs?’
will be displayed for this step.
Press the ‘OK’ button to change
to 24 hour clock.
Note: When 12 hour clock is
set a small ‘a’ will be displayed for
‘AM’ and a small ‘p’ for ‘PM’.
Baby alert
You can set your parent unit
to give a warning ‘beep’ if the
noise levels in your baby’s room
activate the light on the parent
unit. This is a really useful feature
if the volume of your parent unit
is turned down and you are just
using the noise indication light to
monitor the noise levels in your
baby’s room.
At the parent unit:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Sound Alert’. Press
the
‘OK’ button.
2. ‘On?’ will be displayed. Press
the ‘OK’ button to turn the alert
on or the ‘Menu’ button to exit
without changing the setting. You
will hear a confirmation ‘beep’ and
‘Saved’ will be briefly displayed.
To turn the baby alert off, follow
the steps above. ‘Off?’ will be
displayed. Press the ‘OK’ button.
You will hear a confirmation
‘beep’ and ‘Saved’ will be briefly
displayed.
To change the alert tone volume:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Sound Alert’. Press
the ‘OK’ button.
Hush Comfort plus.indd 8 7/12/11 20:35:57

9
2. Use the ‘Up/Down’ buttons
to scroll to ‘Volume’. Press the
‘OK’ button.
3. Use the ‘Up/Down’ buttons
to change the volume level. Press
the ‘OK’ button.You will hear a
confirmation ‘beep’ and ‘Saved’
will be briefly displayed.
Note: 5 blocks on the display =
maximum volume.
Lullaby
You can soothe your baby to
sleep by a gentle lullaby from the
baby unit. There are 5 lullabies
to choose from. You can switch
the lullabies on and off from
the parent and they will play for
approximately 15 minutes.
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Lullaby’. Press the
‘OK’ button.
2. ‘Play?’ is displayed. Press the
‘OK’ button to play the lullaby or
use the ‘Up/Down’ buttons to
scroll to ‘Select New’ and press
the ‘OK’ button.
3. The number of the current
lullaby is displayed. Use the
‘Up/Down’ buttons to scroll to
the lullaby that you would like to
play or select ‘Play All?’. Press
the ‘OK’ button.You will hear a
confirmation ‘beep’ and ‘Saved’
will be briefly displayed.
4. ‘Lullaby’ is displayed. Press the
‘OK’ button twice.
The lullaby will begin to play on
the baby unit.
To stop playing the lullaby, press
the ‘OK’ button twice when you
are in ‘Lullaby’ mode.
Note: The lullabies will stop
playing automatically after
approximately 15 minutes.
Hush Comfort plus.indd 9 7/12/11 20:35:57

10
Temperature
It is very important for your baby’s
health to ensure that they are
kept at a safe temperature. This
includes the room temperature,
baby’s temperature, baby clothing
and bedding (contact your local
health authority to ensure that
you are aware of the current
guidelines). Your baby monitor
can help by displaying the current
room temperature on the baby
unit and parent unit. It can even be
set to alert you if it falls outside of
a set range.
Changing the temperature
range
You can set the upper and lower
temperature limits of your baby
monitor so that you are alerted
if the temperature in the baby’s
room goes above or below your
pre-set range.The temperature
displayed on the parent unit will
flash and an alert, if set, will sound.
At the parent unit:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Temperature’.
Press the ‘OK’ button.
2. Use the ‘Up/Down’ buttons to
scroll to ‘Set Range’ and press
the ‘OK’ button. The current
upper temperature range is
displayed, e.g.,‘Up limit xx’.
3. Use the ‘Up/Down’ buttons
to change the upper temperature
level. Press the ‘OK’ button.You
will hear a confirmation ‘beep’ and
‘Saved’ will be briefly displayed.
4. The lower range limit is now
displayed e.g.,‘Low limit xx’.
5. Use the ‘Up/Down’ buttons
to change the lower temperature
level. Press the ‘OK’ button.You
will hear a confirmation ‘beep’ and
‘Saved’ will be briefly displayed.
Setting the temperature alert
You can set your parent unit to
give an additional ‘double beep’
warning to alert you that the
temperature has moved outside
of the pre-set range.
At the parent unit:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Temperature’.
Press the ‘OK’ button.
2. Use the ‘Up/Down’ buttons to
scroll to ‘Temp Alert’ and press
the ‘OK’ button.
3. ‘Alert On?’ will be displayed.
Press the ‘OK’ button to turn the
alert on or the ‘Menu’ button to
exit without changing the setting.
You will hear a confirmation
‘beep’ and ‘Saved’ will be briefly
displayed.
To turn the temperature alert off,
follow the steps above. ‘Alert
Hush Comfort plus.indd 10 7/12/11 20:35:57

11
Off?’ will be displayed. Press
the ‘OK’ button.You will hear a
confirmation ‘beep’ and ‘Saved’
will be briefly displayed.
Changing from Centigrade to
Fahrenheit
Your monitor is pre-set to display
the temperature in Centigrade
but you can change this to
Fahrenheit.
At the parent unit:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Temperature’.
Press the ‘OK’ button.
2. Use the ‘Up/Down’ buttons to
scroll to ‘Degree F?’. Press the
‘OK’ button to select Fahrenheit
or the ‘Menu’ button to exit
without changing the setting. You
will hear a confirmation ‘beep’ and
‘Saved’ will be briefly displayed.
To change back to Centigrade
follow the steps above. ‘Degree
C?’ will be displayed. Press the
‘OK’ button.You will hear a
confirmation ‘beep’ and ‘Saved’
will be briefly displayed.
Parent to parent paging
This is a useful feature if one
parent is in the baby’s room and
needs to contact the other parent.
You can also use this feature to
‘find’ a mislaid parent unit.
At the baby unit:
1. Press and hold the ‘Page’
button for 2 seconds and then
release. The parent unit will emit
a tone.
At the parent unit:
1. When the page tone sounds
you can silence it by pressing any
button on the parent unit.
2. If you wish, you can speak to
your partner in the baby’s room.
Press and hold the ‘Talk’ button
and speak into the front of the
parent unit. Release the ‘Talk’
button to hear what is said in the
baby’s room again.
Talk to your baby
You can speak to your baby from
the parent unit, perhaps as assurance
that you are on your way.
At the parent unit:
1. Press and hold the ‘Talk’
button and speak into the front of
the parent unit. Release the ‘Talk’
button to hear your baby again.
Note: You will not be able to
hear your baby until you release
the ‘Talk’ button.
Hush Comfort plus.indd 11 7/12/11 20:35:58

12
Night-light
The baby unit has a night-light
providing comfort and reassurance
for your baby. You control the
night-light rom the parent unit.
At the parent unit:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Night-Light’. Press
the
‘OK’ button.
2. ‘On?’ will be displayed. Press
the ‘OK’ button to turn the night
light on or the ‘Menu’ button to
exit. You will hear a confirmation
‘beep’ and ‘Saved’ will be briefly
displayed. A light bulb icon will
appear in the display of the parent
unit to remind you that the baby
unit night-light is on.
To turn the night light off again,
follow the steps above. ‘Off?’ will
be displayed. Press the ‘OK’ button.
You will hear a confirmation ‘beep’
and ‘Saved’ will be briefly displayed.
The light bulb icon will disappear.
Baby feed timer
If your baby is in a routine of
regular feeding intervals you can
set the baby monitor to alert you
when your baby’s feeds are due.
You can choose to:
Set the time of the day or
night (24 hour clock) that
your baby’s next feed is due or
Set the interval between your
baby’s feed start times, e.g.,
every 3 hours 30 minutes.
Don’t forget to include the
time it takes to feed your baby.
Note:You need to set the time
and date of your parent unit to use
the baby feed timer. See page 7.
Set the first or next feed time
At the parent unit:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘FeedTime’. Press the
‘OK’ button.
2. ‘Set Time’ is displayed. Press
the ‘OK’ button.
3. ‘Hour’ is displayed and a
number between 00 and 23 (for
the hours of the day in 24 hour
clock). Use the ‘Up/Down’
buttons to scroll to the hour of
your baby’s feed. Press the ‘OK’
button.
•
•
Hush Comfort plus.indd 12 7/12/11 20:35:58

13
4. ‘Minute’ is displayed and a
number between 00 and 59 (for
the minutes of an hour). Use the
‘Up/Down’ buttons to scroll
to the minutes past the hour
for your baby’s feed. Press the
‘OK’ button. You will hear a
confirmation ‘beep’ and ‘Saved’
will be briefly displayed.
Set the interval for following
feeds
At the parent unit follow the
steps 1-4 above, then:
5. ‘Set Time’ is displayed. Use the
‘Up/Down’ buttons to scroll to
‘Set Interval’. Press the ‘OK’
button.
6. ‘Hour’ is displayed and a
two-digit number for the hours
between your baby’s feeds. Use
the ‘Up/Down’ buttons to scroll
to the hour between your baby’s
feeds eg 03. Press the ‘OK’
button.
7. ‘Minute’ is displayed. Use the
‘Up/Down’ buttons to scroll
to the minutes after the hour
between your baby’s feeds e.g.,
30. Press the ‘OK’ button.You
will hear a confirmation ‘beep’ and
‘Saved’ will be briefly displayed.
Note: Please remember to switch
the feed alarm on as detailed in
the next section.
Turn the feed alarm on
At the parent unit follow the
steps 1-7 beginning on the
previous page and then:
8. ‘Set Interval’ is displayed. Use
the‘Up/Down’ buttons to scroll to
‘Alarm’. Press the‘OK’ button.
9. ‘On?’ will be displayed. Press
the ‘OK’ button to turn the feed
alarm on or the ‘Menu’ button to
exit. You will hear a confirmation
‘beep’ and ‘Saved’ will be briefly
displayed. An alarm bell icon will
appear in the display of the parent
unit to remind you that the baby
feed alarm is set.
To turn the feed alarm off again,
follow the steps above. ‘Off?’
will be displayed. Press the
‘OK’ button.You will hear a
confirmation ‘beep’ and ‘Saved’
will be briefly displayed. The alarm
bell icon will disappear.
To change the alert tone volume:
1. At step 9 above,use the ‘Up/
Down’ buttons to scroll to
‘Volume’ and press the‘OK’ button.
2. Use the ‘Up/Down’ buttons
to change the volume level. Press
the ‘OK’ button.You will hear a
confirmation ‘beep’ and ‘Saved’
will be briefly displayed.
Note: 5 blocks on the display =
maximum volume.
Press any button on the parent
unit to silence the alarm.
Hush Comfort plus.indd 13 7/12/11 20:35:59

14
Sound sensitivity
Some babies are louder than
others! You can customise the
sound sensitivity of your baby
monitor to suit your baby. Set
the sensitivity to ‘High’ for a quiet
sleeper with a soft cry and set to
‘Low’ if your baby tends to make a
noise whilst sleeping or can make
quite loud noises before they are
truly crying.
At the parent unit:
1. Press the ‘Menu’ button and
then use the ‘Up/Down’ buttons
to scroll to ‘Sensitivity’. Press the
‘OK’ button.
2. ‘Level’ will be displayed. Use
the ‘Up/Down’ buttons to change
the sensitivity setting and press
the ‘OK’ button. You will hear a
confirmation ‘beep’ and ‘Saved’
will be briefly displayed.
Note: 5 blocks on the display =
maximum sensitivity.
Low power
In normal use your baby unit
will have a constant low level
communication with the parent
unit at all times. With the
Hush baby monitor you can
choose to reduce this level
of communication or power
usage so that the baby unit only
communicates with the parent
unit when there are sounds in
your baby’s room higher than the
set sensitivity level.
Note: It may take up to 8
seconds for the baby unit to
transmit a signal to the parent unit
to establish digital communication
when low power mode is
switched on.
At the baby unit:
1.To switch low power mode on,
slide the switch underneath the
baby unit to ‘On’.
Hush Comfort plus.indd 14 7/12/11 20:35:59

15
If you are experiencing
problems with your baby
monitor, there are some
quick and easy checks you can
do to help solve the problem.
The parent and baby units
will not power on
Please check that you have
correctly installed the
batteries in the parent unit
and that the mains power for
the baby unit and parent unit
charging pod is connected and
switched on.
The ‘Link’ light on the
parent unit is flashing, the
noise indication light is not
functioning and you cannot
hear sounds from your baby’s
room
You may have moved out of
range of the baby unit. Move
the parent unit closer and wait
5 seconds for the ‘Link’ to re-
establish.
You may need to manually
re-establish the link. Turn both
units off and then press and
release the ‘Power’ button
on the baby unit. Press and
hold the ‘Power’ button for 2
seconds on the parent unit.
•
•
•
After a few seconds the green
‘Link’ light will come on.
You can’t hear your baby on
the parent unit and the ‘Link’
light is still glowing steadily
Check that the volume on the
parent unit is turned up.
You may need to increase the
sensitivity of the parent unit.
See page 14.
The baby monitor is making a
high pitched ear-piercing noise
This can happen if the baby
and parent unit are too close
to each other. Move the
parent unit further apart from
the baby unit.
Clean the charging contacts
with a soft, dry cloth.
If you are experiencing any
difficulty after making the
above checks, please call the
helpdesk for further assistance.
Helpdesk
The helpdesk is open from
9.00am to 5.30pm, Monday to
Friday (excluding bank holidays)
and can be contacted on
0161 925 1981.
•
•
•
•
•
Simple solutions
Hush Comfort plus.indd 15 7/12/11 20:36:00

16
Changing the parent unit
batteries
The parent unit is supplied with
2 x AAA Nickel Metal Hydride
Rechargeable Batteries. To change
the batteries please refer to page
5 of this guide.
Only use recommended
batteries or those of an
equivalent type.
Batteries are to be inserted
with the correct polarity.
Follow the diagram in the
battery compartment.
DO NOT short circuit the
supply terminals.
Promptly remove exhausted
batteries from the parent and
baby unit and replace if the
operating times have become
reduced over time.
Remove the batteries from
the parent and baby unit if
they will not be used for an
extended period of time.
DO NOT attempt to recharge
non-rechargeable batteries.
Dispose of dead batteries
properly.
DO NOT mix old and new
batteries or batteries or
batteries of different types.
(i.e., alkaline/standard)
•
•
•
•
•
•
•
•
DO NOT incinerate used
batteries.
DO NOT dispose of batteries
in a fire, as they may explode
or leak.
DO NOT attempt to open
the battery outer casing.
Batteries are harmful if
swallowed, so keep away from
young children.
•
•
•
•
General information
Hush Comfort plus.indd 16 7/12/11 20:36:00

17
Product guarantee
This product has a warranty
of 12 months and is therefore
guaranteed to be free from
defects in materials and
workmanship during that period.
If you experience a problem
within that time, simply call the
Helpdesk on 0161 925 1981.
If your problem cannot be solved
by our Helpdesk, you will
need to return your product
to the place it was purchased.
Remember to take your receipt
as proof of purchase as it must be
produced before the warranty
can be honoured. This product
must have been used only for the
intended purpose and not been
subjected to wilful or accidental
damage.
This warranty does not cover
damage caused by excessive
voltage or lightning.
If this product has been tampered
with in any way, the warranty shall
be considered null and void.
This guarantee does not affect
your statutory rights.
WEEE Directive
WEEE Directive – Directive
2002/96/EC of the European
Parliament and Council of 27th
January 2003 on waste electrical
and electronic equipment.
At the end of the product’s
lifecycle, you should not
throw this product into the
normal household waste but
take it to a collection point for
the recycling of electrical and
electronic equipment. The ‘WEEE’
symbol below, on the product,
user manual and packaging
indicate this.
Please contact your local
authority if you need more
information about the collection
points in your area.
For more information telephone
Envirowise on 0800 585794.
Hush Comfort plus.indd 17 7/12/11 20:36:00

Hush Comfort plus.indd 18 7/12/11 20:36:00

Hush Comfort plus.indd 19 7/12/11 20:36:01

Helpline
0161 925 1981
Nov11/Issue 1
Hush Comfort plus.indd 20 7/12/11 20:36:01