Husky 008510 Installation instructions

WARNING:
Designed for use in Diesel Exhaust Fluid (DEF)
dispensers only.
NOTE: Always adhere to installation / usage instructions and warning. Improper use may result in injury, damage or
hazardous spill.
1. Turn off dispenser and relieve line pressure.
2. Apply DEF compatable thread sealant to NPT threads of mating tting.
3. Only connect to DEF compatible and 304 stainless steel ttings - see page 2 for
applicable seal congurations.
4. Install at the nozzle or other appropriate location for 1" BSPP Male x 1" NPT Female
ttings.
5. Tighten rmly, approximately 15 - 20 lbf•ft / 20.3 - 27 N•m, but do not overtighten.
6. Pressurize system and visually check for leaks.
VERIFY SMOOTH ROTATION OF ALL SWIVEL JOINTS AFTER INSTALLATION.
DO NOT OVERTIGHTEN
Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com
Page 1 009338-5 9/2018
MADE IN THE USA
INSTALLATION INSTRUCTIONS
IF DRIVE OFF OCCURS
Daily
• Check for leaks / stains
• Check for damage
• Check for smooth rotation of all
swivel joints.
Monthly
• Measure gap at joint - a credit
card should not t in the gap
(0.03 in / 0.76 mm).
• Check "remove after" date.
Annually
• Check for electrical conductivity
• Only clean / rinse exterior surfaces
of DEF product with deionized water.
• All drive aways, maintenance and
inspection activities must be logged
using the serial number of the
individual product.
• Apply city, state, or federal testing
regulations as appropriate.
ANY TEST / INSPECTION
FAILURE REQUIRES IMMEDIATE
EQUIPMENT REPLACEMENT OR
REMOVAL FROM SERVICE.
Diesel Exhaust Fluid (DEF) Swivels
Model 008510
Recommended Installation, Maintenance
and Inspection Instructions
008510 DEF
SWIVEL
TESTING / MAINTENANCE / INSPECTION
• Turn off dispenser and relieve line pressure.
• Inspect the entire dispensing system for damage.
• Pressurize system and visually check for leaks.
• Check for smooth rotation of all swivel joints.
• Measure gap at joint - if a credit card ts in the gap (0.03 in / 0.76 mm) do not reinstall.
• Check for electrical conductivity.
Important safety InstructIon - save these InstructIons In areadIly accessIble locatIon.

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com
Page 2 009338-5 9/2018
APPLICABLE SEAL CONFIGURATIONS
Model 008510 Swivel thread type: 1 x 11 Male BSPP thread one end; 1 x 11 1/2 Female NPT other end.
Figure 3.1
Husky BSPP gasket
compression seal
Option 2
Flange
surfaces
must
mate
Mating Device
BSPP port
Husky o-ring
compression
seal
(Figure 2.1)
Husky
BSPP
tting plug
▪ Seal formed by Husky o-ring.
▪ Husky gasket not required.
Option 1
Hose BSPP port
Hose BSPP port
compression seal
(Figure 1.1)
Husky BSPP
tting plug
▪ Seal is in mating device port.
▪ Husky gasket or o-ring seal not
required.
Option 3
▪ Seal formed by Husky gasket.
▪ Husky o-ring not required.
▪ Thread Husky gasket onto BSPP
tting plug. Do not press on.
Mating Device
BSPP port
Husky gasket
compression seal
(Figure 3.1)
Husky BSPP
tting plug
Figure 2.1
Husky o-ring
compression seal
Figure 1.1
Hose BSPP port compression
seal (installed in hose port)

CAUTION:
VERIFY SMOOTH ROTATION OF ALL SWIVEL JOINTS AFTER INSTALLATION.
DO NOT OVERTIGHTEN.
ALWAYS ADHERE TO INSTALLATION / USAGE INSTRUCTIONS AND WARNINGS.
Improper use may result in injury, damage, or hazardous spill.
WARRANTY
VAPOR PRODUCTS – Husky Corporation will, at its option, repair, replace, or credit the purchase price of any Husky®
manufactured product which proves upon examination by Husky, to be defective in material and/or workmanship for a period of one (1)
year of installation or fteen (15) months from the manufacture date of shipment by Husky, whichever occurs rst. The warranty period on
repaired or replacement vapor recovery products is only for the remainder of the warranty period of the defective product.
CONVENTIONAL PRODUCTS – Husky Corporation will, at its option, repair, replace, or credit the purchase price of any Husky
manufactured product which proves upon examination by Husky, to be defective in material and/or workmanship for a period of one (1)
year from the manufacture date of shipment by Husky.
Buyer must return the products to Husky, transportation charges prepaid. This warranty excludes the replaceable bellows,
bellows spring assembly, spout assembly and scuff guard, unless (i) damage is obvious when the product is removed from shipping carton
and (ii) the defective product is returned to Husky prior to use. This warranty does not apply to equipment or parts which have been installed
improperly, damaged by misuse, improper operation or maintenance, or which are altered or repaired in any way.
The Warranty provisions contained herein apply only to original purchasers who use the equipment for commercial or
industrial purposes. There are no other warranties of merchantability, tness for a particular purpose, or otherwise, and any other such
warranties are hereby specically disclaimed.
Husky assumes no liability for labor charges or other costs incurred by Buyer incidental to the service, adjustment, repair, return,
removal or replacement of products. Husky assumes no liability for any incidental, consequential, or other damages under any warranty,
express or implied, and all such liability is hereby expressly excluded.
Husky reserves the right to change or improve the design of any Husky fuel dispensing equipment without assuming any
obligations to modify any fuel dispensing equipment previously manufactured.
• Use of equipment is at individuals’ own risk.
• Always abide and adhere to city, state, and
federal regulations regarding use and
installation of dispensing equipment.
• Always follow the product manufacturer’s
installation and maintenance instructions.
• Always turn off all power to dispenser during
maintenance and inspection activities.
• Always close the shear valves during
maintenance and inspection activities.
• Always relieve pressure from system prior to
performing maintenance activities.
• Always replace or remove from service
damaged or leaking dispensing equipment
immediately.
• Always report leaks / spills / accidents to
appropriate authorities.
• Always wear appropriate safety equipment
during maintenance activities.
• Always have appropriate re extinguishing
equipment within 5 ft / 1.5 m of dispensers.
• Always clean / rinse exterior surfaces of DEF
product with deionized water.
• Always place containers on the ground
before lling.
• Always discharge static electricity before
using or servicing equipment by touching
a metal part of the dispenser before and
after fueling vehicle.
• Never smoke within 20 ft / 6.1 m of dispensers.
• Never keep in service past recommended life.
• Never leave the nozzle unattended while
dispensing fuel.
• Never use sparking or aming devices within
20 ft / 6.1 m of dispensers.
• Never use power tools near dispensers or
to aid in the installation process.
• Never use cell phone within 20 ft / 6.1 m
of dispensers.
• Never reenter car when fueling vehicle.
• Never allow gasoline to touch eyes or skin.
• Never use at ow rates in excess of
regulatory guidelines.
• Never use at ow rates less than 5 gpm /
18.9 Lpm.
• Never dispense ammable material into
unapproved containers.
• Never dispense fuel without a valid
driver’s license.
Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com
Page 3 009338-5 9/2018
general warnings / instructions pertaining to arisk of fire, electric shock
or injury to persons:
Important safety InstructIon - save these InstructIons In areadIly accessIble locatIon.