Husqvarna 96051009300 Setup guide

ILLUSTRATED PARTS LIST
MFG. ID NO. 96051009300
CUSTOMER CATALOG NO. CTH 194
PRODUCT NO. 960 51 00-93
586 18 25-26
47
47

2
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
6
2
1
3
11
4
10
5
9
8
7
wheel_art_1-tex
WHEELS AND TIRES
KEY PART
NO. NO. DESCRIPTION
1 532 05 91-92 Cap Valve Tire
2 532 06 51-39 Stem Valve
3 532 13 83-36 Rim Front
4 532 05 99-04 Tube Front (Service Item Only)
5 532 10 62-22 Tire Front 15 x 6.0-6
6 532 12 49-57 Fitting Grease (Front Wheel Only)
7 532 12 49-59 Bearing Flange (Front Wheel Only)
8 532 17 50-39 Cap Axle Blk 1 50 x 1 00
9 532 42 05-31 Tire Rear 18 x 9.5-8
10 532 12 49-26 Tube Rear (Service Item Only)
11 532 13 83-37 Rim Asm 8" Rear
- - 532 14 43-34 Sealant, Tire (10 oz. Tube)
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
DECALS
27
27
KEY PART
NO. NO. DESCRIPTION
1 581 57 83-01 Decal Warning Sym. CE
2 581 57 97-01 Decal Warning Eng. Sym.
3 581 62 73-01 Decal, Badge
4 586 04 97-01 Decal Replacement
5 581 57 84-01 Decal, Lower Dash
8 532 44 67-75 Decal Side Panel
9 581 57 98-01 Decal Warning Service/Fire
11 581 57 91-01 Decal Mower Cut Finger Symbol
KEY PART
NO. NO. DESCRIPTION
314
21
3
5
1
99
14 4
11
2
11
8
23
24 22
14 581 57 96-01 Decal Chassis Hot Muffler
21 532 44 11-89 Decal Belt Schematic
22 532 44 51-02 Decal, Battery
23 532 44 46-19 Decal, Bypass
24 532 44 54-93 Decal, Info/Warning
- - 532 44 14-09 Pad, Footrest Pad LH
- - 532 44 14-10 Pad, Footrest Pad RH
- - 586 18 25-20 Manual Operator's (Euro)

3
M
FUSE
STARTER
SOLENOID
BATTERY
REVERSE SWITCH (NOT IN REVERSE)
SEAT SWITCH (NOT OCCUPIED)
FULL BAG
IGNITION
UNIT
HOUR
METER
CHASSIS HARNESS
CONNECTOR (C1)
(MATING SIDE)
DASH HARNESS
CONNECTOR (C1)
(MATING SIDE)
FUEL
LINE
FUEL SHUT-OFF
SOLENOID
(IF SO EQUIPPED)
C1
S
M
B
G
L
2
3
1
6
A2
A1
M
SPARK
PLUGS GAP
(2 PLUGS ON
TWIN CYL. ENGINES)
(OPTIONAL)
NON-REMOVABLE
CONNECTIONS
REMOVABLE
CONNECTIONS
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED
CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY
SHOULD BE RE-INSTALLED TO
PROPERLY SECURE YOUR
WIRING.
SCH19
IGNITION SWITCH
CIRCUITPOSITION
OFF
B+A1
RUN/OVERRIDE
B+S+A1START
M+G+A1
B+A1RUN
“MAKE”
L+A2
PTO SWITCH
(DISENGAGED)
BLACK
BLACK /WHITE
BLUE
BLUE BLACK
GREEN
BLACK
YELLOW
BLK/WHT
BLACK
BLK/WHT
DER
WHITE
WHITE
GRAY
GRAY
BLACK
YELLOW
POWER OUTLET
(OPTIONAL)
12V
BLACK
BLUE
BLACK
BROWN
HEADLIGHTS
LIGHT SWITCH
ORANGE
CLUTCH/BRAKE
(PEDAL UP)
WHITE
GREEN
GREEN
BLUE RED
BAG PRESENT SWITCH
(BAG ATTACHED)
SHORTING CONNECTOR
BAG FULL SWITCH
(NOT FULL)
9
BUZZER
BLACK
BLACK
BLACK
BLUE BLACK
5
6
C1
4
C1
BROWN
8
C1
DER RED
1
2
3
654
98
123
456
89
ELECTRIC CLUTCH
BLACKRED
REGULATOR STATOR
28 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED)
CHARGING SYSTEM OUTPUT
9-16AMPDC@3600 RPM
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
SCHEMATIC
38
38

4
30
33
34
22
79 21
26
40
71
16
TC06S
28
55
With Service Minder Option
4646
43
27
99
25
108
83
107
2
102
105
29
With Charge Indicator Option
142
(+) (-)
143
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
ELECTRICAL
32
32

5
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
ELECTRICAL
32
32
KEY PART
NO. NO. DESCRIPTION
1 532 43 71-57 Battery
2 532 44 09-23 Screw Hex Hd Cap M6 x 1.12MM
16 532 17 61-38 Switch Interlock Push-In
21 532 40 02-52 Harness Socket Light w/4152J
22 532 00 41-52 Bulb Light
25 532 44 13-82 Cable Starter Red
26 532 17 51-58 Fuse
27 873 51 04-00 Nut Keps Hex 1/4-20 unc
28 532 44 13-83 Cable, Ground Black
29 532 40 15-45 Switch, Seat
30 532 19 33-50 Switch, Ign
33 532 41 19-35 Key/Chain
34 532 11 07-12 Switch Light/Reset
40 581 58 64-01 Harness Ign. Dash
43 532 19 25-07 Solenoid
46 532 40 17-63 Gauge Serviceminder Hrmtr
50 532 17 46-51 Switch PTO
55 817 06 05-12 Screw Thdrol 5/16-18 x 3/4 TYTT
71 532 44 08-20 Harness Ign. Chassis
79 532 17 52-42 Socket Asm. Bulb
83 532 43 67-74 Nut Square M6 x 1.8.5 x 11MM
99 817 72 04-08 Screw 1/4-20 x 1/2
102 532 44 12-62 Harness Pigtail Tex ROS Tuff Torq.
105 532 40 75-68 Switch Reverse
107 532 18 03-79 Switch Tall Bagger
108 532 42 10-62 Switch Snapmount
142 583 85 78-01 Charge Port Pigtail
143 532 44 80-59 Charge Port
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

6
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
CHASSIS AND ENCLOSURES
39
39
68
68
68
68
183
183
236
236
34
343
235
235
68
68
213
218
180
52
217
228
228
194
338
347
189
282
162
287
162
284
283
199
194
194
36
36
37
198
chassis-TexCrd-Gen2_TEX LT HUSQ_ 9
177
175
176
5
345
344
176
176
182
176
130
151
130
150
137
137
214
14
204
25
297
191
15
130
130
18
3
238
239
234
234
205
202
203
206
189
189
152
319
309
130
340
368
308
367
189
130 342
349
159
159
342
189
159
159
366
62
334
118
119
118
119
339

7
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
CHASSIS AND ENCLOSURES
39
39
KEY PART
NO. NO. DESCRIPTION
3 581 05 63-01 Logo
5 585 52 98-04 Dash
14 532 44 12-67 Hood
15 532 44 14-28 Lens LH
18 532 44 13-68 Grille
25 532 44 14-27 Lens RH
34 580 91 09-01 Plate Engine
36 817 06 05-12 Screw 5/16-18 x 3/4
37 532 44 13-69 Fender
52 873 68 05-00 Nut Lock 5/16-18
62 872 11 06-08 Bolt Rdhd Sqnk. 3/8-16 x 1 Gr. 5
68 817 49 05-08 Screw Thdrol 5/16-18 x 1/2
118 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
119 873 68 06-00 Nut Crownlock 3/8-16 unc
130 532 41 63-58 Screw #10 x 0.750
137 532 40 75-90 Bumper Dash
150 532 40 75-37 Air Duct
151 532 40 78-07 Bracket Pivot
152 532 19 95-35 Shield Browning
159 817 00 06-12 Screw Hexwsh Thrd 3/8-16 x 3/4
162 532 14 24-32 Screw
175 532 19 94-72 Crossmember
176 532 40 07-76 Screw 10-24 x 5/8
177 532 19 52-28 Bushing Steering
180 583 90 27-01 Chassis
182 532 43 67-76 Dash Lower
183 874 52 05-20 Bolt 5/16-18 x 1-1/4
189 817 00 05-12 Screw 5/16-18 x 3/4
191 532 41 65-01 Insert Reflective RH
194 873 90 05-00 Nut Lock Hex Flange 5/16-18
198 532 44 15-52 Indicator Deck Lift
199 532 41 87-39 Plate Deck Lift
202 532 44 13-42 Vent Side Hood RH
203 532 44 13-43 Vent Side Hood LH
204 532 44 13-75 Vent Top Hood
205 532 44 13-44 Skirt Hood Side RH
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
206 532 44 13-45 Skirt Hood Side LH
213 874 76 05-12 Bolt 5/16-18 x 3/4
214 532 19 91-45 Clip Retainer Tinner
217 532 40 91-67 Rod Pivot
218 532 19 63-95 X-Piece Hood Stop
228 532 19 51-61 Stud Fastner
234 532 40 47-42 Bumper Hood
235 532 40 61-29 Spacer Fender
236 873 93 05-00 Nut Lock 5/16-18 unc
238 532 44 13-74 Trim
239 532 40 48-83 Clip
282 532 41 41-10 Clip Retainer
283 532 44 72-12 Console Deck Lift LH
284 532 44 72-20 Console Shft SRD RH
287 817 60 04-06 Screw 1/4-20 x 3/8
297 532 40 66-65 Insert Reflective LH
308 532 17 18-77 Bolt 5/16-18 unc x 3/4
309 581 32 89-07 Backplate
319 581 31 39-06 Lever Bagger
334 532 44 25-37 Bracket Engine
338 532 43 66-40 Bolt Shoulder
339 532 43 66-41 Lever Bagger Full Asm.
340 581 32 90-01 Door Pnt Battery tray Tex CRD
342 532 43 59-38 Supprt Fender
343 532 44 07-49 Clip
344 532 43 89-70 Control EZ Mulch
345 532 44 06-39 Knob
347 532 44 28-87 Hitch Tow
349 532 43 66-06 Fuel Tank Support Bracket
366 581 31 46-02 Bracket RH Front
367 581 31 45-02 Bracket LH Front
368 581 42 48-01 Full Lever
KEY PART
NO. NO. DESCRIPTION

8
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
DRIVE
40
40
351
116
103
161
143
125
195
143
99
17
33
205
205
183
37
2
205
61
205
37
2
1
33
183
73
185
29
30
159
6
125
355
339
125
125
339
226
227
56
116
27
359 335
363
352
342
342
359
35
184 221
drive-TexCrd-Gen2_K46_pedal_8
315
143 280
335
362
364
38 175
360
279
360
311 312
140
313
309 143
186
189
49
314
52
51
50
90
160
210
214
211
215
166
211
222
163
42 64
159
160
167
203
30
188
197
196
125

9
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
1 – – – – – – Transaxle, Tufftorq K46DF
(446488) (Order parts from
transaxle manufacturer.)
2 532 12 35-83 Key Square
6 532 12 40-28 Bushing Snap
17 532 43 62-27 Spring Brake K46
27 817 49 05-28 Screw 5/16-18 x 1-3/4
29 532 44 27-95 Rod, Brake
30 819 13 16-16 Washer
33 812 00 00-01 Ring E
35 532 40 10-31 Rod, Brake, Park
37 532 12 17-49 Washer 25/32 x 1-5/8 x 16 Ga.
38 532 16 96-13 Nyliner Snap In
42 532 12 48-72 Cover, Foot Pedal
49 872 11 06-14 Bolt 3/8-16 unc
50 532 19 43-27 Idler Flat
51 873 90 06-00 Lock Nut 3/8-16
52 532 19 43-26 Idler V-Groove
56 532 44 27-81 V-Belt, Drive
61 532 44 51-51 Pulley Transaxle K46
64 532 19 78-65 Shaft Asm. Pedal Brake Control
73 874 49 05-44 Bolt Hex 5/16-18 x 3.75
90 532 44 36-05 Keeper Belt Clutching
99 532 44 39-47 Rod Spring Bypass
103 873 35 05-00 Nut Hex Jam 5/16-18 unc
116 873 90 05-00 Nut Lock Hex Flange 5/16-18
125 817 00 05-12 Screw 5/16-18 x 3/4
140 810 04 04-00 Washer Lock Hvy Helical 1/4
143 817 49 05-08 Screw 5/16-18 x 1/2
159 876 02 04-12 Pin Cotter 1/8 x 3/4
160 532 16 94-84 Retainer Clip
161 532 10 57-09 Spring, Return, Clutch
163 532 44 27-93 Rod Control
166 532 42 91-64 Nut Push
167 532 40 52-57 Latch Brake Parking
175 532 42 93-59 Shaft Asm. Shift
183 532 13 70-57 Spacer Axle
184 532 44 14-07 Handle Parking Brake
185 872 11 06-22 Bolt 3/8-16 unc x 2-3/4
186 532 19 43-21 Spacer Retainer
188 532 19 43-23 Link Clutch
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION
189 532 43 36-11 Bellcrank Ground Drive
195 580 45 69-01 Bracket Rod Brake CRD Tex
196 817 00 06-16 Screw
197 532 19 58-04 Link Clutch
203 819 11 11-16 Washer 11/32 x 11/16 x 16 Ga.
205 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.
210 532 40 09-80 Rocker Asm. Pedal Control
211 532 12 01-83 Bearing Nylon
214 532 42 12-63 Pedal Forward
215 532 41 94-82 Pedal Reverse
221 532 40 31-87 Retainer Spring Clip Handle
222 879 21 20-10 Washer 21/32 x 1-1/4 10 Ga.
226 532 40 15-64 Bracket Strap Torque
227 817 49 05-12 Screw Thdrol 5/16-18 x 3/4
279 532 44 42-83 Link Shift
280 819 11 10-12 Washer 11/32 x 5/8 x 12 Ga.
309 532 16 55-81 Plate Fstnr Cross Shf
311 532 16 98-45 Washer Nylon
312 532 16 56-14 Hub Tapered
313 874 78 04-16 Bolt Hex Fin 1/4-20 unc x 1 Gd5
314 532 44 47-13 Retainer Belt
315 817 58 05-20 Screw Thdrol 5/16-18 x 4.25
335 532 19 95-34 Pulley-V-Idler.Grnd.Dr.Plated
339 532 43 68-67 Strap Torque K46
342 532 18 26-82 Keeper Belt
351 532 43 69-98 Bracket 97 CRD Deck Sway
352 532 43 56-45 Bracket Idler
355 532 43 56-69 Bracket
359 817 49 06-10 Screw 3/8-16 x 5/8
360 532 44 47-14 Nut Hex 5/16-24
362 532 43 68-12 Idler Flat
363 532 44 27-80 Spacer
364 532 44 30-32 Bracket Idler
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
DRIVE
40
40

10
1
29
SPARK ARRESTER KIT
92
45
21 20
94
69
engine-tex_Kohl_47
2
87
37
28
37
79
18
15
97
96
12
11
41
42
85
9
90
122
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
ENGINE
24
24
108
102
102
Guard_assembly_38

11
KEY PART
NO. NO. DESCRIPTION
1 – – – – – – Engine Kohler Model No. SV591-3210
(585507601) (Order parts from engine
manufacturer.)
2 580 53 23-01 Muffler
9 584 90 80-01 Keeper Belt Engine
11 532 40 00-08 Clutch
12 532 40 50-97 Pulley Engine
15 581 28 99-01 Tank Fuel
18 532 43 02-20 Fuel Cap
20 532 18 38-97 Control Throttle
21 532 41 63-58 Screw # 10 x 0.750
28 532 13 70-40 Fuel Line
29 532 13 71-80 Spark Arrester Kit
37 532 12 34-87 Clamp Hose
41 532 12 61-97 Washer
42 810 04 07-00 Washer Lock 7/16
45 873 51 04-00 Nut Keps Hex 1/4-20 unc
69 532 18 59-09 Gasket
79 532 19 23-34 Screw 5/16-18 x .75
85 532 17 39-37 Bolt Hex 7/16-20 x 4 x Gr. 5-1.5 Thr
87 537 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems
90 817 00 06-16 Screw 3/8-16 x 1
92 817 12 06-16 Screw 3/8-16 x 1
94 583 95 53-01 Tube Exhaust
96 819 09 14-16 Washer 9/32 x 7/8 x 16 Ga.
97 817 67 04-12 Screw 1/4-20 x 3/4
102 817 06 05-16 Screw 5/16-18 x 1
108 532 42 30-41 Cover Pulley Engine
122 532 42 19-22 Extension Drain Oil
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
ENGINE
24
24
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

12
19
60
59
58
70
68
69
28
28
13
22
64
35
67
63
57
63
6
15
14
5
81
13 13
8
53
62
81
61
82
15
14
14
14
15
80
85
14
15
80
82
80
6
4
15
14
86
9
8
9
8
67
66
7
7
2
80
steering-tex_TTR_13
16
20
1
21
71
72
33
45
122
122
118
118
118
118
26
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
STEERING ASSEMBLY
41
41

13
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
STEERING ASSEMBLY
41
41
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
1 532 43 97-40 Wheel, Steering
2 532 43 68-70 Axle Asm., Front
4 532 43 68-73 Spindle Asm., LH
5 532 43 68-74 Spindle Asm., RH
6 532 12 49-31 Washer Thrust 0.75 x 1.23
7 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.
8 812 00 00-29 Ring, Klip #T5304-75
9 532 12 12-32 Cap, Spindle
13 532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.
14 810 04 06-00 Washer, Lock 3/8
15 873 54 06-00 Nut, Crown Lock 3/8-24 unf
16 532 44 42-13 Shaft Steering
19 532 19 47-29 Plate Steering
20 532 44 14-25 Steering Boot
21 532 43 77-47 Adapter, Wheel Steering
22 532 19 48-45 Bushing, Strg. Blk
26 532 43 97-43 Insert, Wheel Steering
28 817 00 06-12 Screw 3/8-16 x 3/4
33 810 04 05-00 Washer Lock
35 532 44 07-70 Gear, Sector Plate
45 819 11 38-12 Washer 11/32 x 2-3/8 x 12 Ga.
53 532 18 89-67 Washer Hardened .793 x 1.637 x .060
57 532 40 74-65 Bracket Upstop
58 532 19 47-47 Bolt Shoulder Sector Pivot CFM
59 532 19 47-48 Washer Thrust Sector Steering
60 873 97 10-00 Nut Flange Lock 5/8-11
61 532 43 68-84 Draglink, LH
62 532 43 68-85 Draglink, RH
63 817 00 05-12 Screw 5/16-18 x 3/4
64 532 19 98-49 Retainer Clip Spring Steering
66 871 02 07-48 Bolt Hex Fghd 7/16-14 x 3 Serr
67 532 19 47-37 Bushing PM Front Axle
68 873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5
69 532 19 91-62 Washer 1.5 x .505 x .118
70 532 19 61-97 Bracket Deck Susp. Front
71 532 19 07-52 Shaft Extension Steering
72 532 42 89-82 Bolt 5/16-18
80 532 00 13-70 Washer
81 532 43 68-87 Link Cross RH
82 532 44 21-47 Pivot Bolt
85 532 44 18-73 Pivot RH
86 532 44 18-72 Pivot LH
118 532 40 60-13 Bushing Axle
122 532 44 49-62 Cap Gear Sector
KEY PART
NO. NO. DESCRIPTION

14
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
MOWER DECK
44
44
43
102
120
114
115
119
117
19
121
115
119
111
110
110
23
97
75
14
84
20
99
100
100
127
16
91 128
1
127
128
91
16
154
154
98
3
98
32
127
128 91 16
20
127 128
91
16
19
17
43
27
18
96
101
117
113
112
116
101
16 17
75
14
13
118
11
13
125
42
95
75
14
16
76
11
94
5
129
130 131
163
161
117
163
162
117
117
163
160
117
163
159
117
72
20
20
20
20
250
250
250
250
250
250
36
124
45
34
33
35
85
87
88
86
137
136 139
139
138
tex-deck_TexCRD-Gen2_60_r1
146
143
144
145
141
140
104
2
2
11
11
247
2
11 11
248
105
2
249

15
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
MOWER DECK
44
44
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
1 580 97 33-01 Deck Weldment
2 532 42 30-62 Palnut 1/4
3 873 90 05-00 Nut Lock Hex Flange 5/16 - 18
5 817 00 05-10 Bolt 5/16-18
11 532 13 77-29 Screw Thd Roll 1/4 - 20 X 5/8
13 872 11 06-12 Bolt Carr Sh 3/8 - 16 X 1-1/2 Gr. 5
14 532 15 60-85 Keeper Belt Idler
16 873 90 06-00 Nut Lock FlG 3/8 - 16 unc
17 532 40 02-34 Nut Flange Lock Top
18 532 18 76-90 Washer Spacer Mandrel
19 532 11 04-85 Bearing Ball Mandrel
20 532 17 39-84 Screw Thread Roll
23 817 49 06-28 Screw Thdrol 3/8 - 16 X 1-3/4
27 532 44 58-86 V-Belt Drive
32 532 44 62-05 Spring Drive
33 580 79 61-01 Mandrel Asm. Tall
34 580 85 47-01 Shaft Asm Mndrl N/Greaseable
35 581 51 79-01 Blade Mower LH
36 532 19 30-03 Bolt/Washer Asm 7/16 - 20 unf
42 817 00 05-12 Screw 5/16-18 x 3/4
43 532 44 32-39 Pulley Mandrel
45 581 65 08-01 Mandrel Asm. Short
71 817 67 06-08 Screw 3/8-16 x 1/2
72 581 45 41-02 Chute Upper
75 532 13 14-94 Pulley Idler Flat
76 532 43 96-40 Washout Port
84 532 44 32-35 Keeper Belt LH Mandrel
85 581 51 80-01 Blade Mower RH
86 532 18 17-13 Bolt 3/8-24 x 1.50 Gr. 8
87 810 03 06-00 Washer Lock Hvy. 3/8
88 532 14 02-96 Washer Hard
91 819 13 20-12 Washer 13/32 x 1-1/4 x 12 Ga.
94 532 19 72-50 Bracket Clutch Cable
95 817 00 06-12 Screw 3/8-16 x 3/4
96 532 40 02-71 Spacer
97 532 18 20-61 Shield Idler Mower
98 532 19 51-61 Stud Fastener
99 532 19 51-86 Arm Suspension Mower Rear
100 532 19 65-39 Bolt Shoulder
101 873 68 09-00 Nut Crownlock 9/16 - 18 unc
102 532 40 25-11 Spacer Bearing Swing Plate
104 581 71 40-01 Mandrel Cover RH
105 532 44 47-55 Mandrel Cover LH
110 532 41 53-56 Gear Output
111 532 43 69-79 Gasket Gearcase
112 532 44 38-52 Shaft Gearcase Adapter
113 532 43 85-33 Plug Oil
114 532 43 85-34 Valve Relief
115 818 03 10-16 Screw Torx #10-24 x 1
116 872 11 04-14 Bolt 1/4-20 x 1.75 Gr. 5
117 873 90 04-00 Nut Hex Flange 1/4-20 unc
118 532 44 32-32 Arm Clutching
119 532 43 81-66 Gearcase Subasm
120 532 44 32-36 Keeper Belt RH
121 532 43 69-85 Washer
124 581 65 07-01 Non Greasable Mandrel Shaft
125 532 44 04-20 Bracket Idler Chassis
127 532 19 34-06 Bolt Shoulder 3/8-16 x 3-5/8 Gr. 5
128 532 17 48-73 Wheel Gauge
129 532 44 32-37 Rod Anti-Sway
130 819 13 13-12 Washer 13/32 x 13/16 x 12 Ga.
131 532 19 42-08 Pin Cotter 5/16 Bow Tie Lock
136 532 43 96-39 Washout Report Remote Hook Up
137 812 00 00-29 Ring Klip
138 532 44 76-67 Hose Washout Port
139 532 44 07-42 Hose 3/8 Clamp
140 580 36 99-01 Guard Sub Asm. LH
141 532 44 77-03 Guard Sub Asm. RH
143 532 43 81-97 Door Mulch
144 532 43 58-61 Pin Hinge
145 532 43 79-88 E-Ring 5/16"
146 532 44 58-96 Spring
154 532 19 98-55 Screw Thd Roll 1/4-20 x 1/2
159 585 30 95-05 Plate 107 CRD LH Side
160 585 30 94-05 Plate 107 CRD LH Front
161 585 31 60-05 Plate 107 CRD RH Front
162 585 31 61-05 Plate 107 CRD RH Side
163 872 11 04-06 Bolt
247 581 26 34-02 Guard Steel
248 581 26 36-02 LH Rear Steel Guard
249 581 26 35-02 LH Rear Steel Guard
250 819 11 12-12 Washer 11/32 x 3/4 x 12 Ga.
- - 580 85 60-01 Mandrel Assembly Tall (Includes
Housing (key # 33), Shaft As-
sembly (key # 34), And Bearing
Only (key # 19) - Pulley/Nut/
Washer And Blade Bolt/Washers
Not Included.)
- - 581 65 05-01 Mandrel Assembly Short (In-
cludes Housing (key # 45), Shaft
Assembly (key # 124), And Bear-
ing Only (key # 19) - Pulley/Nut/
Washer And Blade Bolt/Washers
Not Included.)
- - 581 92 92-01 Replacement Mower Complete
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION

16
7
3
87
10
88
2
89
90 98
97
97
lift-tex_34
91
101*
89 87
100
*Key 91 may be substituted for Key 101
2 532 43 69-96 Deck Lift Weldment
3 532 19 52-31 Lever Asm., Lift RH
7 580 96 23-01 Grip, Lever
10 532 19 63-14 Spring Torsion
87 532 19 42-09 Pin Cotter 7/16 Bow Tie Lock
88 532 44 54-96 Spring Lift Assist
89 819 19 19-12 Washer Clear Zinc
90 532 19 42-08 Pin Cotter 5/16 Bow Tie Lock
91 532 19 51-81 Link Lift Susp Mower Rear
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
97 817 49 06-08 Screw 3/8-16 x 1/2
98 532 19 52-70 Link Lift Susp. Front Mower
100 873 93 06-00 Nut Center Lock 3/8-16 unc
101 532 40 70-03 Link Asm Lift Fixed
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
MOWER LIFT
45
45

17
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION
1 532 43 98-22 Seat
2 532 18 01-66 Bracket Pivot Fender
3 532 14 06-75 Strap, Asm Fender
6 873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc
7 532 12 41-81 Spring, Seat Cprsn
8 532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems
10 532 19 69-77 Pan, Seat
21 532 17 18-52 Bolt, Shoulder 5/16-18
37 873 80 05-00 Nut, Lock 5/16-18 unc
40 532 19 76-61 Handle Slide Seat
41 532 19 82-00 Spring Latch Seat
43 874 76 06-12 Bolt Fin Hex 3/8-16 unc x 3/4
44 819 13 38-12 Washer 13/32 x 2-3/8 x 12 Ga.
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
2
6
1
40
10
37
37
21
21
3
41
7
8
7
8
seat-tex_6.5SL_3
44
43
8
8
6
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
SEAT ASSEMBLY
42
42

18
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
BAGGER
46
46
2
54
8
21
69
42
47
3
3
44
44
55 44
52 52
58
56
56
59
58
59
58
10
55
45 48
44
3
3
42 46
42
Bagger_TexCRD-Gen2_4_r2
50
49
49
49 50
5
43
53
52
51
1
27
28
19
3
7
7
25
26
70 86
84
83
83
88
87
83
89
83
83
83
84
83
85
70
84

19
TRACTOR - MODEL NO. CTH 194 (96051009300), PRODUCT NO. 960 51 00-93
BAGGER
46
46
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
1 532 42 86-10 Tube Handle Bagger
2 532 44 75-72 Applique
3 532 17 48-14 Nut Push
5 532 44 37-62 Frame Asm Top Bagger
7 873 90 04-00 Nut Hex Flange 1/4-20 unc
8 532 44 75-75 Cover Bagger
10 532 44 37-55 Frame Front
19 532 19 42-08 Cotter Pin 5/16 Bow Tie
21 532 44 59-43 Bag Asm
25 532 44 55-28 Latch Bagger
26 817 49 04-12 Screw Hexwsh Thdrol 1 14~20 x 3/4
27 532 44 55-29 Grommet Rubber
28 532 16 57-87 Grip Handle Black
42 532 44 04-28 Christmas Tree Clip
43 532 12 68-75 Clevis Pin
44 532 19 96-87 Bolt 1/4-20 1.50
45 532 44 37-54 Upper U Frame Weldment
46 532 44 55-41 Bagger Corner Close-Out RH
47 532 44 40-79 Bagger Corner Close-Out LH
48 532 44 40-80 Top Bagger Side Close-Out
49 532 17 18-73 Bolt Shoulder 5/16~ 18 TT
50 532 17 18-77 Bolt 5/16-18 unc x 3/4 W/SEMS
51 872 11 05-06 Bolt RDHDSQNK 5/16-18 unc x 3/4
52 873 80 05-00 Nut Lock HX W/INS 5/16-18 UNC
53 532 44 41-95 Bracket Dump Handle
54 532 44 72-18 Bagger TOP Front Handle
55 872 14 05-12 Bolt Rdhd Sq 5/16-18UNCX1 1/2
56 532 42 03-06 Pin Clevis .1830DX1.26 long
58 532 08 51-79 Clip Retainer PM
59 532 44 47-63 Bagger Spread Tube
69 532 42 18-01 Screw #8
70 817 00 06-12 Bolt 3/8-16X3/4
83 873 80 06-00 Nut Lock Hex w/Ins 3/8-16
84 872 11 06-08 Bolt RDHD SQNK 3/8-16 x 1 Gr. 5
85 581 31 44-02 Bracket RH Pivot
86 581 31 43-02 Bracket LH Pivot
87 581 31 48-02 Bracket RH
88 581 31 47-02 Bracket LH
89 581 31 51-04 Tube Asm.

10.23.13 BD