HYBREX Blue Tooth Phone User manual

TO MAKE INTERCOM / OUTGOING CALLS
To make an intercom call or an outgoing call:
Manual Mode
1. Press the [Answer] button on the headset.
2. Press Extension Number or dial External number
3. To End Call press [Answer] button on headset
Auto Mode
Press Extension number or dial External number
To End Call press SPK button on DK2 Phone
GENERAL OPERATION
To Adjust Speaker Volume during a Call
You can adjust the speaker volume during a call by
pressing the volume control buttons on the side of the Ear
and or the volume control keys on the DK2 phone
according to your preference.
Operation Range
The Hybrex DK2 Blue Tooth Interface is a very low power
radio communication device. The radio communication
range between the DK2 and the Headset is approximately
10 meters. Please keep both units within this range for
best communication performance.
EAR PIECE SETUP
Most headsets will allow you to wear the headset on your
right or left per your preference. Please consult your Blue
Tooth Headset user guide for the setup required.
MAINTAINANCE
As high temperature will shorten the battery life, please do
not leave your Headset in an environment with
temperatures over 100ºF or in direct sunlight.
Keep your Headset away from moisture.
To clean, use soft cloth with mild liquid soap to clean the
exterior of your Cordless Headset and phone. DO NOT
use abrasive chemical detergent or material to clean the
Headset.
DO not attempt to pry open the cover of your Cordless
Headset or change the batteries. Seek assistance from
an AUTHORIZED Hybrex dealer near you.
WARRANTY SCOPE
Auto Telecom guarantees our products (excluding the
batteries) as being free of defects in material, design and
workmanship at the time of original purchase and for a period
of twelve (12) months immediately thereafter.
If, during the warranty period, the products malfunction in
normal use and service (by authorized dealer), Auto
Telecom or its authorized dealer will repair or replace the
defective product at no cost to the original purchaser.
Auto Telecom or its authorized dealer may refuse to
provide free warranty service if any of the following
conditions occurs:
1. The product is adapted, modified, or changed.
2. The product exterior is cracked or broken.
3. The serial number label is tampered with or missing.
4. The product has being misused by the user in any way.
5. The product has not being serviced by a Hybrex
AUTHORSED service agent
Repairs or replacements will neither give any right to
extend the original warranty period nor give any right to
start a new warranty period. Replaced faulty parts or
components will become the property of Auto Telecom.
HEADSET SPECIFICATIONS
Frequency 2.400~2.4835GHz
Security 128 Bit
Technology Type Blue Tooth
Auto channel hopping Yes
Working range Up to 10 meters
Talk time 4 hours (headset dependant)
Blue Tooth Version 1.2
.
Blue Tooth Phone
User Guide
Auto Telecom New Zealand Ltd
Ph [phone]
Fax [phone]

BLUE TOOTH HEADSETS
The Hybrex DK2 Phone Blue Tooth interface will integrate
with many brands of headset, Hybrex have tested and
recommend the following headsets
Motorola HS820
Motorola HS810
Netcom GN6110
•g range
CONNECTION TO PHONE
No physical connection to the DK2 phone is required.
TO PAIR HEADSET WITH DK2 PHONE
Before Pairing:
Please ensure Blue Tooth Headset has had its first
maximum charge as recommended by its manufacturer.
•Hold Headset with Mic Boom closed
•Place Blue Tooth Headset into Pairing Mode by
pressing and holding down the answer key until
LED light comes on
•Open Mic Boom, LED on Headset should remain
on
•Press and hold down the DK2 phones “HOLD” key
until “Pairing” is displayed on phone screen
•Release Hold Key
•Waiting until Blue Tooth Headset LED flashes
rapidly
•Phone and Handset are now Paired
Note: Please ensure you only pair one Blue Tooth Device in
the area of work at any one time
TO ACTIVATE DK PHONE INTO HEADSET MODE
To activate the headset mode on DK2 phone:
•Press [SPK][775] to enable the headset mode.
To cancel the headset mode on DK2 phone:
•Press [SPK][775] to cancel the headset mode.
Z248
TO ANSWER INCOMMING CALLS
Manual Mode
To answer incoming call:
•When DK2 phones rings the Blue Tooth Headset will
beep in your ear
•To answer call press the [Answer] button on the Blue
Tooth headset.
To end the conversation of a call:
•Press the [Answer] button again will end the call
•The Blue Tooth Headset will beep to indicate call
ended and will automatically put DK2 phone to
idle state.
Note:
•If you press [SPK] button on the DK2 telephone this
will also end the call directly. But the Blue Tooth
Headset will be left in Auto Answer Mode”. If left in
this state the next incoming call will be answered
automatically by the Headset.
Auto Mode
Headset will be in active when in this mode, please note the
battery time will be more limited when using this mode
To answer incoming call:
•When DK2 phones rings the Blue Tooth Headset will
beep in your ear once
•The Headset will then answer call
To end the conversation of a call:
•Press the SPK key on the DK2 phone
Note:
•If you press [SPK] button on the DK2 telephone will
also end the call directly. But the Blue Tooth
Headset will be left in Auto Answer Mode”. If left in
this state the next incoming call will be answered
automatically by the Headset.