hybsys GSM 108 Gate User manual

User’s Manual
GSM 108 Gate
GSM Wireless Terminal
Characteristic ___________________________________________________________ 2
The instructions to the frontal appearance of GSM 108 Gate_____________________ 2
Indicators and knobs__________________________________________________________2
Instructions to the rear appearance of GSM 108 Gate ___________________________ 3
Ports _______________________________________________________________________3
Installation and Setup_____________________________________________________ 3
Installing the SIM Card______________________________________________________________3
Setting up the Terminal______________________________________________________________3
The Installation for Connect to Ordinary Telephone________________________________________3
The installation connecting to charging device____________________________________________4
The installation for connecting to PBX__________________________________________________5
Operation_______________________________________________________________ 5
Making Calls______________________________________________________________________5
Answering Incoming Calls ___________________________________________________________6
Turn on or turn off the terminal________________________________________________________6
The Information about Signal Quality, Malfunction and Software Version ______________________6
Inquire Signal Quality and Software Version _____________________________________________6
Adjusting the Volume of Voice________________________________________________________6
The Instructions for Terminal’s Running Status ___________________________________________6
Technical Specification ___________________________________________________ 7
Maintenance and storage __________________________________________________ 7
Familiar Trouble and Troubleshooting_______________________________________ 8

Hybrid Systems JSC Users Manual
Page 2 of 8 GSM 108 Gate
Characteristic
•Adopts advanced microprocessor controlling
circuit, runs steadily and its functions are all
complete
•Enhanced high gains external antenna
•Be suitable to GSM900/1800MHz
•Locking terminal, locking SIM card and locking
network can be set up flexibly.
•Diversiform function on calling out or being called
in can be set according to your need
•Display incoming calls
•Barred telephone numbers can be set flexibly
•Prefixed code can be set according to user’s requirement
•Can be connected to charging device
•Can be connected to PBX
•With the function of network management, the parameters can be set through
network manager
The instructions to the frontal appearance of
GSM 108 Gate
The Frontal Appearance of GSM 108 Gate
Indicators and knobs (from up to down)
Status indicator— flashing once in one second indicates that the terminal has been
on GSM network
Used indicator — Staying lit during calls and during parameters’ setting
Warn indicator— Staying lit for less than 10 seconds indicates that the terminal is
dealing with SMS. If it stays lit for more than 10 seconds, there is some trouble with
the terminal.
Reset knob — press this knob, its corresponding board will reset.
Power switch— push to “On” or “OFF” side to turn on or turn off the terminal.

Hybrid Systems JSC Users Manual
Page 3 of 8 GSM 108 Gate
Instructions to the rear appearance of GSM 108 Gate
The Rear Appearance of GSM 108 Gate
Ports
Power port—connect to power adapter
Phone port—connect to a phone
Antenna port—connect to antenna
Installation and Setup
Installing the SIM Card
Proceed as follows:
1. Slide back the SIM door and lift it up
2. Slide the SIM card into the SIM door making sure that the clipped corner of the
SIM card lines up with the clipped corner of the SIM holder
3. Close the SIM door
4. Slide the SIM door to lock the SIM card in place
Setting up the Terminal
The Condition for Installation
The terminal asks for 220V AV power supply. It must be installed in the area
where the GSM network can cover. The strength of the signal can affect the quality of
voice direct.
The Installation for Connect to Ordinary Telephone
Screw off the screws that are on the back of the terminal and pull out the
corresponding circuit board. Install SIM card for every circuit board and install the
circuit board in place, and then tighten the screws.
Install antenna. In order to ensure the quality of voice, antenna must be put beyond
1.5m from the telephone and terminal.
One end of the telephone line connects to the “Phone” port of the terminal, the
other end connects to telephone.

Hybrid Systems JSC Users Manual
Page 4 of 8 GSM 108 Gate
“Power” port connects to power adapter that is connected to220V AC power
supply. About 15—45 seconds later (the time is subject to local wireless network), the
terminal will work in gear.
The sketch for connecting to ordinary telephone: each circuit board can be
connected to one telephone
Draw your attention: Because there are many types of ordinary telephone and their
electric parameters are different .In order to avoid mutual disturbance between
telephone and terminal and affect voice quality .The distance between telephone and
terminal is 1.5m at least.
The installation connecting to charging device
If the users demand to register cost during calls, charging device can be
connected between terminal and ordinary telephone. Charging device register cost
according to the anti-polarity signal that is provided by terminal.
The sketch map of connecting multi-route charging device

Hybrid Systems JSC Users Manual
Page 5 of 8 GSM 108 Gate
The sketch map of connecting to computer charging system
The installation for connecting to PBX
If users want to connect small PBX to this terminal, connect terminal’s “Phone
port” to the PBX.
Operation
Making Calls
Lift the handset or press “hand-free” key, you will hear dialing tone, then you
can dial the telephone numbers you want to call.
Dialing: dialing the telephone numbers you want to call
On completion of dialed digits, you can press “#” to transmit the called
telephone numbers. If you don't dial any key for continual 6 seconds during the
dialing, terminal transmits called telephone numbers automatically.
During calls, if the telephone numbers is not free ones, the terminal sends out
anti-polarity signal (the signal is used to register cost by charging device).
If the calling party or called party hangs up, the terminal stops sending out
anti-polarity signal.
If users dial barred numbers telephone will give out the sound of three-time
toot to ask the user to hang up.

Hybrid Systems JSC Users Manual
Page 6 of 8 GSM 108 Gate
Answering Incoming Calls
When some calls are coming in, if the connected telephone has the function of
displaying incoming calls, the telephone rings and displays the incoming telephone
numbers. Now users can lift the handset or press “hand-free” to answer it.
Turn on or turn off the terminal
Put power switch to “OFF” side to turn off the terminal and put the power
switch to “ON” side to turn on the terminal.
The Information about Signal Quality, Malfunction and Software
Version
If the connected phone has the function of displaying incoming calls, the
telephone rings after the terminal is login onto GSM network successfully and a code
of 8 digits will be displayed .The code indicates the information about signal quality,
malfunctions and software version as follows:
The first two digits indicate the signal quality; it ranges from “00” to “31”.
Stronger the signal is, bigger the digits is. If it is less than 10, the quality of voice will
be poor.
The third and the forth digit is the code of malfunction:“00”: good “11”: failed
in login onto GSM network “22” or “33”: PIN error (PIN code isn’t 1234 or PIN isn’t
disabled), “44”: lock card error, “55”: lock terminal error“77”: lock network error,
“99”: read card error
The later four digits is the code of software version: for example 4060 indicates
the software version code is 4.06.
If the telephone displays “11”or “22” or “33” or “44” or “77” or “99” or the
telephone can’t work in gear, please contact service provider.
Inquire Signal Quality and Software Version
Lift the handset and then dial “***9#”. Hang up as soon as you hear the busy
tone. The telephone rings and displays a code of 8 digits. The code indicates the
information of signal quality and software version as follows:
The first two digits indicate signal quality. It ranges “00” to “31”. Stronger the
signal is, bigger the digits is. If it is less than 10, the quality of voice will be poor.
The third and the forth digits are both standby.
The later four digits is the code of software version: for example 4060 indicates
the software version code is 4.06.
Adjusting the Volume of Voice
Lift the handset or press “hand-free” key.
Dial “*33XY#” and then hang up when hear the sound of toot.
X and Y both belong to the digits that range from 1 to 5. X indicates
microphone volume and Y indicates speaker volume. Level 1 is the lowest volume and
level 5 is the highest.
The Instructions for Terminal’s Running Status
The instruction for initializing terminal
When Power indicator is lit, the terminal begins to initialize. If Status indicator
and Used indicator are flashing simultaneously, the terminal is searching for network.
About 15 45 seconds later, the telephone rings that indicates the process of
initialization terminal finishes. If Warn indicator stays lit, initialization is unsuccessful.
On this condition user can set parameters for the terminal but the terminal can’t be

Hybrid Systems JSC Users Manual
Page 7 of 8 GSM 108 Gate
used to make any calls. If users dial telephone numbers, the Warn indicator will flash
and the telephone will give out the sound of three -time toot to ask the user to hang
up.
While users dialed barred numbers or other error numbers, the telephone gives
out the sound of three-time toot to indicate that user should hang up and redial.
While you are lifting the handset and don’t dial any key for continuous 15
seconds or nobody answer the dialed telephone for 90 seconds after the called
telephone has ringed, the telephone will give out the sound of three-time toot to
indicate the user to hang up. If the user doesn’t hang up for a long time, all indicating
sound will stop after 1 minute.
While calls coming in, Used indicator flashes. IF user answers the call, the Used
indicator stays lit until the call is hung up.
When user is lifting the handset, Used indicator stays lit until user hangs up.
When the terminal receives SMS, Warn indicator and Used indicator both stay lit that
indicates that the terminal is dealing with SMS.
If Warn indicator stays flashing and the telephone continuously gives out the
sound of three-time toot, which indicates that the terminal is on the warning status.
Please hang up.
Technical Specification
•Working condition Environment temperature: 0~+50
•Relative humidity: 10%~95%
•Air pressure: 86~106kpa
•Environment yawp: ≤60Db (A)
•Working frequency: GSM900/GSM1800MHz
•Stability of frequency: better than 2.5PPM
•Signal sensitivity: -103DbM
•Transmit power: <2w
•Power Supply: 220v±15% AC
•The maximal distance between terminal and telephone: 100M
Maintenance and storage
The terminal should be saved in the desiccant place.
If three are some matters with the terminal, please send it to the appointed
repair center. (The damages that are caused by error operation are beyond the scope
of our free maintenance). Don't take apart the terminal by yourself without our
agreement
The packed terminal should be put in dry and ventilated place. The number of lays
of piled terminal can’t more than 10. The condition of the storehouse is listed as
follows:
•Temperature: -10 to +45
•Relative humidity: ≤95%
You should ensure that there is no corrosive gas in the storehouse too.

Hybrid Systems JSC Users Manual
Page 8 of 8 GSM 108 Gate
Familiar Trouble and Troubleshooting
Phenomena Trouble Trouble Shooting
Warn indicator
stay bright for
long time
Failed in login
onto GSM
network
1. The signal is too weak Please move the
terminal to the place where signal is stronger.
2. Check whether antenna is connected well.
3. SIM card is locked. Please contact the
service provider.
Power indicator
isn’t bright
Having not
connect to
power supply
1. Check whether the adapter is connected
well. 2. There is some trouble with the power
adapter Please contact the terminal provider.
Only free
numbers can
be called out
The residual
money on SIM
card is too less Add money to the SIM card
Can’t hear of
sound during
calls
The malfunction
on the
telephone
Change the connected telephone with a good
one
Poor voice
quality during
calls or there is
echo during
calls
The voice
volume is too
high or the
signal of GSM
network is too
weak.
1. Adjust the voice volume to be lower. 2. The
local signal is too weak. Move the terminal to
the place where signal is stronger. 3. Make
the antenna is longer from the telephone 4.
The voice quality of the connected telephone
isn’t good. Change the connected telephone
5. Trouble on the network.
No ringing
sound
The malfunction
on the
telephone
1. Malfunction on connected telephone 2.
Malfunction on terminal. Please contact the
terminal provider.
Incoming calls
can’t be
answered
The connected
telephone does
not match the
terminal or
forbidding
answering
incoming calls
are set
1. Chang the connected telephone with a
suitable one. 2. Forbidding answering
incoming calls is set. Please contact the
service provider.
FUTURE CONTACTS
Hybrid Systems JSC
BULGARIA, 1303 Sofia
70 Hristo Botev Blvd, fl. 2
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
WEB: http://www.hybsys.bg