HYDAC FILTER SYSTEMS LOGO! TDE User manual

LOGO
!
REPLACEMENT
MODULE TDE
for FAM-5
Installation Manual
English (translation of original instructions)
Keep for future reference.
Documentation no.: 4359963

Content
FAM 5 en-US Page 2 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
Content
Content ..........................................................................................................2
Preceding note..............................................................................................2
Replacing the Logo! of the TDE module.....................................................3
Preparing the Logo! of the TDE module......................................................4
Preparing the Logo! of the TDE module for assembly.................................6
Installing the Logo! of the TDE module........................................................7
Determining the configuration of the FAM ...............................................10
Model code................................................................................................10
IndexKeine Indexeinträge gefunden.............................................................11
Preceding note
This instruction manual is meant to be a supplement to the Operating- and
Maintenance instructions for the FAM. Therefore, it is limited to the
replacement of a defective Logo! of the TDE module. Everything else, such
as the explanation of symbols and formal explanations can be taken from the
Operating and Maintenance instructions for the FAM.
The Logo! of the TDE replacement module is supplied as a spare part,
without being configured. After being installed, it must be adapted to the
model version of your FAM. In order to do this, use the Operating and
Maintenance Instructions for the FAM.
Use the Operating and Maintenance instructions for the
FAM.

Replacing the Logo! of the TDE module
FAM 5 en-US Page 3 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
Replacing the Logo! of the TDE module
In this chapter, you will find the required specifications to replace the
defective Logo! of the TDE module with a new module. The listed illustrations
show the module at the front of the switch cabinet. It is at the head in the
case of the FAM. The replacement process described does not change due
to this with regard to how it is carried out.
DANGER
Electric shock
Danger of fatal injury
►Any work involving the electrical equipment
may only be done by a properly trained,
certified electrician.
The jobs listed below may only be carried out by properly trained, certified
electricians, who meet the following conditions:
Only specialist personnel with training as electricians and
the following knowledge:
•Safe handling/use of tools
•Fitting and connection of electrical lines, electrical
machinery, sockets, etc.
•Checking the phase sequence
•Product-specific knowledge
•Knowledge about how to handle operating media.
Screwdriver

Replacing the Logo! of the TDE module
FAM 5 en-US Page 4 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
NOTICE
Unit in a condensation state
Risk of a short circuit
►Do not switch on the Logo! of the TDE module when it is in a
condensation state.
►Allow it to come to room temperature before commissioning it.
►While doing so, do not expose the Logo! of the TDE module to any
direct heat radiation from heating devices.
If the unit is exposed to, or has been exposed to, climatic fluctuations
(temperature fluctuations, humidity), moisture can condense on or inside the
unit (unit in a condensation state).
If there is condensation in or on the unit or if the unit has been exposed to
temperature fluctuations, allow it to come to to room temperature before
starting it up.
Preparing the Logo! of the TDE module
In order to disassemble the Logo! of the TDE module, proceed as follows:
1.
Switch off the E-Box via the main
switch.

Replacing the Logo! of the TDE module
FAM 5 en-US Page 5 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
2.
Pull the E-Box's power plug.
3.
Open the door to the E-Box with
the suitable key.
4.
Disconnect all cables and
connection plugs on the rear side
of the Logo! of the TDE module.
Unscrew the set screws out of
the holding brackets
counterclockwise.
Remove the four holding
brackets and push the Logo! of
the TDE module from the back to
the front out of the cut-out
section in the door.
5.
The disassembly of the Logo! of
the TDE module is complete.

Replacing the Logo! of the TDE module
FAM 5 en-US Page 6 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
Preparing the Logo! of the TDE module for assembly
Check the module for transport damage. The module may only be installed
and operated in perfect technical condition, in compliance with this
document.
If no sealing cord has been glued in place in groove (A) on the rear side of
the module's front panel, insert the sealing cord provided in groove (A) and
cut the sealing cord to length so that the joint closes with a tight seal.
NOTICE
Leaks at the Logo! of the TDE module
Moisture/water enters into the E-Box via the Logo! of the TDE module
►Ensure that the sealing cord is inserted cleanly. If the inserted sealing
cord is twisted or if the joint is not adequately closed, leakage can
occur.
►Cut the sealing cord to length and insert it such that the joint closes
with a tight seal.

Replacing the Logo! of the TDE module
FAM 5 en-US Page 7 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
Installing the Logo! of the TDE module
In order to install the Logo! of the TDE module, proceed as follows:
1.
Prepare the Logo! of the TDE
module for installation according
to Chapter "Preparing the Logo!
of the TDE module for
assembly", page 6.
2.
Insert the Logo! of the TDE
module from the front through
the cut-out section in the door.
Ensure that it is installed
with the correct orientation
(top/bottom).
All ports/sockets are located at
the bottom.
3.
Pre-mount the set screws
provided in the holding brackets.
The tips of the set screws must
point toward the wide ends of
the holding brackets.
4.
Hook the holding brackets into
the corresponding recesses in
the unit as follows and fix the
unit in place by tightening the
set screws until the front of the
Logo! of the TDE module is flush
with the surface of the switch
cabinet at the fastening points.
Note the maximum
torque of 0.1 Nm.

Replacing the Logo! of the TDE module
FAM 5 en-US Page 8 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
Only the Logo! of the
TDE module with the four
mounted holding brackets fulfil
protection class IP65.
5.
Insert all cables and connection
plugs into the corresponding
ports on the rear side of the
Logo! of the TDE module.
6.
Close the door to the E-Box with
the suitable key.
7.
Plug in the power connector and
switch the touch panel on at the
main switch.
8.
Check the display of the Logo!

Replacing the Logo! of the TDE module
FAM 5 en-US Page 9 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
of the TDE module at starting.
The user interface starts
automatically.
9.
The assembly of the Logo! of
the TDE module is complete.

Determining the configuration of the FAM
FAM 5 en-US Page 10 / 12
MOWA LogoTDE 4359963 en 2018-05-23.docx
2018-05-08
Determining the configuration of the FAM
In order to adapt the Logo! of the TDE replacement module to your FAM, you
require the model version given in the model code. In order to decode this,
use the following table.
Adapt the configuration of the replacement module according to the model
version. The guidelines for this are the chapters "Configuration menu,
Changing the configuration, Exiting the configuration menu" in the Operating
and Maintenance Instructions for the FAM.
Model code
FAM
-
X
-
X
-
X
-
X
-
X
-
X
-
H
-
X
-
Z
-
X
/
X
Product
FAM = FluidAqua Mobil
Filter Size
…
Operating fluid
…
Mechanical type
…
Voltage/frequency/power supply
…
Filter size fluid filter
…
Vacuum pump
…
Heater
Z = No heater
H = Heater (for 200 … 359 V = 1 kW, for
360 … 690 V = 2.4 kW)
Control concept
…
Instrumentation
Z = Without
A
=
AquaSensor (AS)
AC = AquaSensor (AS)+ContaminationSensor
(CS)
ACS = AquaSensor (AS) + ContaminationSensor (CS)+
SensorMonitoring Unit (for displaying and saving the
measured values)
Modification number
…
Supplementary details
…