HydroSure 100205196 User manual
1
100
2
05196
W
T’-wT
,wU
,w
Tw
wNww,,-
w
H
H
A,R
xz
T
R
q
AjS
A
W,-O,
D
P
DTAww
SwDw
2
PARTS LIST
C 4
E
Pu
H
G
A
C
3
J
0
p
s
HARDWARE LIST
I
K
@
M N
@
4
J
L
® @
0 p
a
s T
ASSEMBLY INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS AND IDENTIFY ALL PARTS
BEFORE STARTING ASSEMBLY
1.
(
See Figure
1
) Remove the
L
ock
N
uts
(
O) and Flat
W
ashers
(
P) from each
of the two Axles
(
B). Slide the Axles
(
B) through the holes at the bottom
of the Frame
(
A).
2.(See Figure 2) Slide Wheels (C) onto
the ends of each Axle (B) and secure
using the Flat Washers (P) and Lock
Nuts (O). Make sure that the valve
stems are facing outward. Do not
overtighten.
3.
(
See Figure
3
) Insert the end of the
H
andle
(
E) through the handle hub
of the frame
(
A).
5
B
Crank
Hub
E
I ' .
e
4.(See Figure
4
) Place the
H
ose
R
eel (D)
onto the Frame (A) and align the
handle stem with the handle hub
(
*
bearing house). Insert the handle
stem into the
H
andle (E) hole.
5. (See Figure
5
) Align the
H
andle (E)
mounting holes with the handle stem
mounting holes, insert a Bolt (K) into
the hole furthest away from the
H
ose
R
eel (D) and loosely fasten with a
L
ock
N
ut (Q). Insert a Bolt (K) into the
hole nearest to the
H
ose
R
eel (D) and
fasten with a Dome
N
ut (S).
6. (See Figure
6
) Position the opposite
end of the
H
ose
R
eel (D) to the
underside of the Frame (A) between
the two mounting holes. Align a U-
bracket with the mounting holes and
secure using
C
oach Bolts (I) and
L
ock
N
uts (Q). Tighten securely.
6
Figure 4
D
Crank Stem '
E
Figure 5
Q
I
Figure 6
Hose
Coupling
-Bracket Hose
, I \f Coupling
7. (See Figure
7
) Slot the Pull Handle (F)
onto the Frame (A) and align the
mounting holes. Secure with
C
oach
B
olts (J)
,
Flat
W
ashers (R) and Lock
Nuts (Q).
8.
(See Figure 8)
Place Flat
W
ashers (R)
onto the end of two
B
olts (L) and
insert into the mounting holes of the
Pull Handle (F). Attach
B
asket (H) to
these bolts using the basket
’
s
mounting tabs and secure with Flat
W
ashers (R) and Hex Nuts (M).
9. (See Figure
9
) Place a Rubber
W
asher (T) into the water coupling
and attach Leader Hose (G). Attach
the opposite end of the Leader
Hose (G) to your water supply.
Attach your garden hose to the
garden hose connector and wind
around Hose Reel (D).
7
Figure 7
Figure 8
Figure 9
F
.
I,
T
Table of contents
Other HydroSure Outdoor Cart manuals
Popular Outdoor Cart manuals by other brands
Eagle
Eagle 348352 Assembly instructions
Cornwell Tools
Cornwell Tools CTBMM500NGBKE Assembly instructions
Gorilla Carts
Gorilla Carts GCR-7 manual
Tie Down Engineering
Tie Down Engineering Roof Zone PENETRATOR 65028 Assembly instructions
TradeQuip
TradeQuip 6003T owner's manual
Copernicus
Copernicus Tech Tub2 FTT718-UV Assembly guide
