Hypex Electronics Nilai500DIY User manual

Mono kit
Assembly
Instructions

2 3
EL-7
1x
Control Back
H07U005859
EL-6
1x
Control Front
H07U006555
EL-5
1x Terminal
T6.3A
250V
T6.3A
250V
E09U006286
K03U001035
EL-4
1x Switch
E14U001062
M04U005969
EL-3
1x Mounting Plate
EL-2
1x PS500DIY
H02U005632
EL-1
1x Nilai500DIY
H01U005520
Electronics
Parts
TX-20
TX-10
2.5mm
1.5mm
Included:
3.5mm
OR
7mm
+
12mm
+
not included:
Tools
Chapter
Page
Tools
2
Parts
2
Introduction
5
User Instructions
5
Safety precautions
6
Assembly
7
Amplifier & Supply
8
Case
10
Backpanel
11
Cables
15
Lid & Frontpanel
17
System information
20
Troubleshooting & Support
21
Warranty & Disclaimer
22
Revisions
22
Notes
23
Table of Contents
F99U005992
MC-10
2x
M3x5
MC-9
4x
3.3mm
MC-8
4x
M3x10
MC-7
1x
M4
MC-6
1x
4.3mm
MC-5
1x
4.5mm
MC-4
8x
4.5mm
MC-3
4x
M4x10
MC-2
5x
M4x10
MC-1
2x
Mounting set Case
M3x7
Not used:
4x CA-6
1x Top
M02U005975
CA-5
1x Front
M02U005976
CA-4
1x Back
M02U005980
CA-3
4x
Feet
M99U005983
CA-2
2x
Side
M02U005971
CA-1
1x Bottom
M02U005977
Case

2 3
EL-7
1x
Control Back
H07U005859
EL-6
1x
Control Front
H07U006555
EL-5
1x Terminal
T6.3A
250V
T6.3A
250V
E09U006286
K03U001035
EL-4
1x Switch
E14U001062
M04U005969
EL-3
1x Mounting Plate
EL-2
1x PS500DIY
H02U005632
EL-1
1x Nilai500DIY
H01U005520
Electronics
Parts
TX-20
TX-10
2.5mm
1.5mm
Included:
3.5mm
OR
7mm
+
12mm
+
not included:
Tools
Chapter
Page
Tools
2
Parts
2
Introduction
5
User Instructions
5
Safety precautions
6
Assembly
7
Amplifier & Supply
8
Case
10
Backpanel
11
Cables
15
Lid & Frontpanel
17
System information
20
Troubleshooting & Support
21
Warranty & Disclaimer
22
Revisions
22
Notes
23
Table of Contents
F99U005992
MC-10
2x
M3x5
MC-9
4x
3.3mm
MC-8
4x
M3x10
MC-7
1x
M4
MC-6
1x
4.3mm
MC-5
1x
4.5mm
MC-4
8x
4.5mm
MC-3
4x
M4x10
MC-2
5x
M4x10
MC-1
2x
Mounting set Case
M3x7
Not used:
4x CA-6
1x Top
M02U005975
CA-5
1x Front
M02U005976
CA-4
1x Back
M02U005980
CA-3
4x
Feet
M99U005983
CA-2
2x
Side
M02U005971
CA-1
1x Bottom
M02U005977
Case

4
F99U005987
MS-4
M3x6
7x
MS-3
M3x6
9x
MS-2
M3x6
2x
MS-1
2.9X9.5
2x
Mounting set
K02U005993
CB-9
1x
Z14A15L1
1
14
CB-8
1x
Z4B10L1
CB-7
1x
Z2B21L1
CB-6
1x
K03U001032
CB-5
1x
Z4C38L1
CB-4
1x
Z12C23L1
CB-3
1x
Z1A11L1
CB-2
1x
Z1A10L4
CB-1
1x Z2B25L1
Cable set
5
FunctionPosition Remarks
Open
1 - 2
2 - 3
Low gain
Mid gain
High gain
11.8 dB
21.8 dB
27.8 dB
Overall gain is set to 11.8dB (3.9x)
Overall gain is set to 21.8dB (12.3x)
Overall gain is set to 27.8dB (24.5x)
LOW GAIN
MID GAIN
HIGH GAIN
Input Gain Jumper
The Amplifier Module contains a pinheader (J200) with jumper to alter the input gain setting:
This simple 3.5mm mini-jack connection allows you
to create a simple network between all of your
DIYclassD amplifiers for a more seamless power up
and standby experience. When connected, it will
control the power of all other products in the system.
When you turn on the preamplifier, the rest of the
system will turn on automatically.
all new DIYclassD amplifier kits.
12V Trigger
feature that comes equipped on
The 12 Volt Trigger is a powerful
The front switch can be used to turn-
on and turn-off (standby) the power
amplifier when the 12 Volt trigger
option is not used (when used, the
12V trigger overrules the front
switch).
Front Switch
Adjust the brightness of the front indicator light:
LED Switch
FULL
OFF
HALF
User Instructions
Not included in the kit
Included in the kit
Full Hypex DIY case
Switch Mode Power Supply
®
Nilai Amplifier
Full internal cable harness
All required connectors
This assembly instruction
All required mounting materials
This assembly instruction covers the general
assembly instructions for this specific model. For
detailed technical information about the used
modules please refer to the datasheet on our website.
1x TX-10 / TX-20 / 1.5 and 2.5mm hex key
Interconnects
Loudspeaker cables
Power cable
Tools as described on page 2
®
Thank you for purchasing the Nilai 500DIY Amplifier
®
kit, powered by our Nilai technology.
PS500DIY (1x)
This mono kit can be a power amp for your passive
loudspeakers. We offer two kind of kits:
®
Nilai 500DIY Mono kit 1x500W
Please note the different models. This assembly
instruction describes how to assemble one of these
models. The mono and stereo kit only offer balanced
inputs. If your source only offers unbalanced outputs
you can use one of our interconnects to connect them
properly.
Please read the safety instructions on the next page
before assembling, installing and/or operating the
®
Nilai mono kit.
®
Nilai 500DIY (1x)
®
Nilai 500DIY Stereo kit 2x250W
®
The Nilai amplifier and the Switch Mode Power Supply
used in this kit are:
®
Nilai 500 DIY Amplifier kit, a brief introduction

4
F99U005987
MS-4
M3x6
7x
MS-3
M3x6
9x
MS-2
M3x6
2x
MS-1
2.9X9.5
2x
Mounting set
K02U005993
CB-9
1x
Z14A15L1
1
14
CB-8
1x
Z4B10L1
CB-7
1x
Z2B21L1
CB-6
1x
K03U001032
CB-5
1x
Z4C38L1
CB-4
1x
Z12C23L1
CB-3
1x
Z1A11L1
CB-2
1x
Z1A10L4
CB-1
1x Z2B25L1
Cable set
5
FunctionPosition Remarks
Open
1 - 2
2 - 3
Low gain
Mid gain
High gain
11.8 dB
21.8 dB
27.8 dB
Overall gain is set to 11.8dB (3.9x)
Overall gain is set to 21.8dB (12.3x)
Overall gain is set to 27.8dB (24.5x)
LOW GAIN
MID GAIN
HIGH GAIN
Input Gain Jumper
The Amplifier Module contains a pinheader (J200) with jumper to alter the input gain setting:
This simple 3.5mm mini-jack connection allows you
to create a simple network between all of your
DIYclassD amplifiers for a more seamless power up
and standby experience. When connected, it will
control the power of all other products in the system.
When you turn on the preamplifier, the rest of the
system will turn on automatically.
all new DIYclassD amplifier kits.
12V Trigger
feature that comes equipped on
The 12 Volt Trigger is a powerful
The front switch can be used to turn-
on and turn-off (standby) the power
amplifier when the 12 Volt trigger
option is not used (when used, the
12V trigger overrules the front
switch).
Front Switch
Adjust the brightness of the front indicator light:
LED Switch
FULL
OFF
HALF
User Instructions
Not included in the kit
Included in the kit
Full Hypex DIY case
Switch Mode Power Supply
®
Nilai Amplifier
Full internal cable harness
All required connectors
This assembly instruction
All required mounting materials
This assembly instruction covers the general
assembly instructions for this specific model. For
detailed technical information about the used
modules please refer to the datasheet on our website.
1x TX-10 / TX-20 / 1.5 and 2.5mm hex key
Interconnects
Loudspeaker cables
Power cable
Tools as described on page 2
®
Thank you for purchasing the Nilai 500DIY Amplifier
®
kit, powered by our Nilai technology.
PS500DIY (1x)
This mono kit can be a power amp for your passive
loudspeakers. We offer two kind of kits:
®
Nilai 500DIY Mono kit 1x500W
Please note the different models. This assembly
instruction describes how to assemble one of these
models. The mono and stereo kit only offer balanced
inputs. If your source only offers unbalanced outputs
you can use one of our interconnects to connect them
properly.
Please read the safety instructions on the next page
before assembling, installing and/or operating the
®
Nilai mono kit.
®
Nilai 500DIY (1x)
®
Nilai 500DIY Stereo kit 2x250W
®
The Nilai amplifier and the Switch Mode Power Supply
used in this kit are:
®
Nilai 500 DIY Amplifier kit, a brief introduction

6
Correct disposal of this product: This symbol indicates that this product should not be disposed of with your household waste, according to the
WEEE directive (2012/19/EU) and your national law. This product should be handed over to an authorized collection site for recycling waste
electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment
and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the
correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off
your waste equipment for recycling, please contact your local city office, waste authority, or your household waste disposal service.
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with a dry cloth.
7.
Natural convection should not be impeded by covering the
module (apart from the end applications housing). Do not
block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the protective earth
/ grounding mains inlet. Protective earth is provided for
your safety.
10.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the
manufacturer.
12.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
13.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
14.
This apparatus shall not be exposed to dripping or
splashing, and no object filled with liquids, such as
vases or beer glasses, shall be placed on the apparatus.
15.
Do not overload wall outlets and extension cords as this
can result in a risk of fire or electric shock.
16.
This apparatus has been designed with Class-I
construction and must be connected to a mains socket
outlet with a protective earthing connection.
17.
This apparatus has been equipped with a rocker-style
AC mains power switch. This switch is located on the
rear panel and should remain readily accessible to the
user.
18.
The MAINS plug or an appliance coupler is used as the
disconnect device, so the disconnect device shall remain
readily operable.
19.
Do not run any cables across the top or the bottom of the
module. Apply fixtures to cables to ensure that this is not
compromised.
20.
Before using this product, ensure all cables are correctly
connected and the power cables are not damaged. If you
detect any damage, do not use the product.
21.
Changes or modifications not expressly approved by
Hypex Electronics will void compliance and therefore the
user's authority to operate the equipment.
22.
Service or modifications by any person or persons other
than by Hypex Electronics authorized personnel voids the
warranty.
Gebruik voor dit apparaat een geaard stopcontact.
Verwenden Sie für dieses Gerät eine geerdete
Steckdose.
Utilisez une prise électrique mise à la terre pour cet
appareil.
Utilice un tomacorriente con conexión a tierra para
este aparato.
Use a grounded electrical outlet for this appliance.
The exclamation point within an equilateral triangle is
intended to alert the user of the prescence of important
operating and maintaining (servicing) instructions in
the literature accompanying the appliance.
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
prescence of uninsulated “dangerous voltage” within
the product’s enclosure, that may be of significant
magnitude to constitute a risk of electric shock to
persons.
Att ention: Observe pr ecautio ns for han dling
electrostatic sensitive devices. This module uses
semiconductors that can be damaged by electrostatic
discharge (ESD).
Précautions de sécurité
Ce unité est sous tension secteur et certaines de ses
pièces accessibles sont sous une tension dangereuse.
Ces pièces doivent dans tous les cas être protégées
contre contacts accidentels. Lors de l'installation, une
prudence extrême s'impose. Ne jamais toucher les pièces
du module quand celui-ci est relié au secteur. Isoler
l'appareil du secteur et attendre 10 minutes pour laisser
à tous les condensateurs le temps de se décharger avant
de le manipuler.
Avertissement: Pour réduire les risques de choc électrique, ne
pas exposer cet appareil à la pluie ou l'humidité.
Les dommages causés par un usage non approprié sont
exclus de la garantie. Ce produit ne contient aucune
pièce devant être entretenue par l'utilisateur.
This unit operates at mains voltage and carries
hazardous voltages at accessible parts. These parts may
never be exposed to inadvertent touch. Observe extreme
care during installation and never touch the internal
modules while the unit is connected to the mains.
Disconnect the unit from the mains and allow all
capacitors to discharge for 10 minutes before handling it.
Warning: To reduce the risk of fire or electric shock, do not
expose this device to rain or moisture.
Damage due to inappropriate handling is not covered by
warranty. This product has no user-serviceable parts.
Safety precautions
7
Result:
Assembly

6
Correct disposal of this product: This symbol indicates that this product should not be disposed of with your household waste, according to the
WEEE directive (2012/19/EU) and your national law. This product should be handed over to an authorized collection site for recycling waste
electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment
and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the
correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off
your waste equipment for recycling, please contact your local city office, waste authority, or your household waste disposal service.
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with a dry cloth.
7.
Natural convection should not be impeded by covering the
module (apart from the end applications housing). Do not
block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the protective earth
/ grounding mains inlet. Protective earth is provided for
your safety.
10.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the
manufacturer.
12.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
13.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
14.
This apparatus shall not be exposed to dripping or
splashing, and no object filled with liquids, such as
vases or beer glasses, shall be placed on the apparatus.
15.
Do not overload wall outlets and extension cords as this
can result in a risk of fire or electric shock.
16.
This apparatus has been designed with Class-I
construction and must be connected to a mains socket
outlet with a protective earthing connection.
17.
This apparatus has been equipped with a rocker-style
AC mains power switch. This switch is located on the
rear panel and should remain readily accessible to the
user.
18.
The MAINS plug or an appliance coupler is used as the
disconnect device, so the disconnect device shall remain
readily operable.
19.
Do not run any cables across the top or the bottom of the
module. Apply fixtures to cables to ensure that this is not
compromised.
20.
Before using this product, ensure all cables are correctly
connected and the power cables are not damaged. If you
detect any damage, do not use the product.
21.
Changes or modifications not expressly approved by
Hypex Electronics will void compliance and therefore the
user's authority to operate the equipment.
22.
Service or modifications by any person or persons other
than by Hypex Electronics authorized personnel voids the
warranty.
Gebruik voor dit apparaat een geaard stopcontact.
Verwenden Sie für dieses Gerät eine geerdete
Steckdose.
Utilisez une prise électrique mise à la terre pour cet
appareil.
Utilice un tomacorriente con conexión a tierra para
este aparato.
Use a grounded electrical outlet for this appliance.
The exclamation point within an equilateral triangle is
intended to alert the user of the prescence of important
operating and maintaining (servicing) instructions in
the literature accompanying the appliance.
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
prescence of uninsulated “dangerous voltage” within
the product’s enclosure, that may be of significant
magnitude to constitute a risk of electric shock to
persons.
Att ention: Observe pr ecautio ns for han dling
electrostatic sensitive devices. This module uses
semiconductors that can be damaged by electrostatic
discharge (ESD).
Précautions de sécurité
Ce unité est sous tension secteur et certaines de ses
pièces accessibles sont sous une tension dangereuse.
Ces pièces doivent dans tous les cas être protégées
contre contacts accidentels. Lors de l'installation, une
prudence extrême s'impose. Ne jamais toucher les pièces
du module quand celui-ci est relié au secteur. Isoler
l'appareil du secteur et attendre 10 minutes pour laisser
à tous les condensateurs le temps de se décharger avant
de le manipuler.
Avertissement: Pour réduire les risques de choc électrique, ne
pas exposer cet appareil à la pluie ou l'humidité.
Les dommages causés par un usage non approprié sont
exclus de la garantie. Ce produit ne contient aucune
pièce devant être entretenue par l'utilisateur.
This unit operates at mains voltage and carries
hazardous voltages at accessible parts. These parts may
never be exposed to inadvertent touch. Observe extreme
care during installation and never touch the internal
modules while the unit is connected to the mains.
Disconnect the unit from the mains and allow all
capacitors to discharge for 10 minutes before handling it.
Warning: To reduce the risk of fire or electric shock, do not
expose this device to rain or moisture.
Damage due to inappropriate handling is not covered by
warranty. This product has no user-serviceable parts.
Safety precautions
7
Result:
Assembly

8
CA-1
TX-10
MS-3
5x
5x
❷
TX-10
MS-4
7x
❶
EL-3
1x CA-1
1x
EL-2
1x
EL-1
1x
MS-4
7x
M3x6
MS-3
9x
M3x6
CB-4
1x
Amplifier & Supply
9
CB-4
J5
❻
4x
MS-3
4x
TX-10
❺
Make sure no occational foil is placed.
Otherwise: remove the foil.
Optional
❹
Read user
instructions
for details.
LOW GAIN
MID GAIN
HIGH GAIN
J200
Optional
❸

8
CA-1
TX-10
MS-3
5x
5x
❷
TX-10
MS-4
7x
❶
EL-3
1x CA-1
1x
EL-2
1x
EL-1
1x
MS-4
7x
M3x6
MS-3
9x
M3x6
CB-4
1x
Amplifier & Supply
9
CB-4
J5
❻
4x
MS-3
4x
TX-10
❺
Make sure no occational foil is placed.
Otherwise: remove the foil.
Optional
❹
Read user
instructions
for details.
LOW GAIN
MID GAIN
HIGH GAIN
J200
Optional
❸

10
TX-20
2x
MC-3
MC-4
❷
4x
MC-9
MC-8
TX-10
❶
MC-9
4x
3.3mm
MC-8
4x
M3x10
MC-4
4x
4.5mm
MC-3
4x
M4x10
MC-1
2x
CA-5
2x
CA-3
4x
Case
11
PowerAmplifier | mono POWERED BY HYPEX ELECTRONICS
100-240V~ 50-60Hz/650W
FUSE T6.3AH/250V
TRIG
LOUDSPEAKER LOUDSPEAKER LED
INPUT
+
-
❷
❶
CA-4
1x
CB-7
1x
CB-6
1x
CB-3
1x
CB-2
1x
CB-1
1x
EL-5
1x
T6.3A
250V
T6.3A
250V
EL-4
1x
MC-4
4x
4.5mm
MC-2
4x
M4x10
MS-1
2x
2.9X9.5
EL-7
1x
CB-5
1x
Backpanel

10
TX-20
2x
MC-3
MC-4
❷
4x
MC-9
MC-8
TX-10
❶
MC-9
4x
3.3mm
MC-8
4x
M3x10
MC-4
4x
4.5mm
MC-3
4x
M4x10
MC-1
2x
CA-5
2x
CA-3
4x
Case
11
PowerAmplifier | mono POWERED BY HYPEX ELECTRONICS
100-240V~ 50-60Hz/650W
FUSE T6.3AH/250V
TRIG
LOUDSPEAKER LOUDSPEAKER LED
INPUT
+
-
❷
❶
CA-4
1x
CB-7
1x
CB-6
1x
CB-3
1x
CB-2
1x
CB-1
1x
EL-5
1x
T6.3A
250V
T6.3A
250V
EL-4
1x
MC-4
4x
4.5mm
MC-2
4x
M4x10
MS-1
2x
2.9X9.5
EL-7
1x
CB-5
1x
Backpanel

12
❽
❼
❻
PowerAmplifier | mono POWERED BY HYPEX ELECTRONICS
100-240V~ 50-60Hz/650W
FUSE T6.3AH/250V
TRIG
LOUDSPEAKER LOUDSPEAKER LED
INPUT
+
-
❺
❹
2x
2x
❸
13
2x
TX-10
MS-1
10
EL-7
❾
PowerAmplifier | mono POWERED BY HYPEX ELECTRONICS
100-240V~ 50-60Hz/650W
FUSE T6.3AH/250V
TRIG
LOUDSPEAKER LOUDSPEAKER LED
INPUT
+
-
❽
❼
❻

12
❽
❼
❻
PowerAmplifier | mono POWERED BY HYPEX ELECTRONICS
100-240V~ 50-60Hz/650W
FUSE T6.3AH/250V
TRIG
LOUDSPEAKER LOUDSPEAKER LED
INPUT
+
-
❺
❹
2x
2x
❸
13
2x
TX-10
MS-1
10
EL-7
❾
PowerAmplifier | mono POWERED BY HYPEX ELECTRONICS
100-240V~ 50-60Hz/650W
FUSE T6.3AH/250V
TRIG
LOUDSPEAKER LOUDSPEAKER LED
INPUT
+
-
❽
❼
❻

14
4x
MC-4
15
CB-5
14
CB-5 J1
13
J6
CB-4
12
11
15
J1
❸❷
❶
7
TX-20
MC-7
1x
M4
MC-6
1x
4.3mm
MC-5
1x
4.5mm
MC-2
1x
M4x10
Cables
MC-2
TX-20
16

14
4x
MC-4
15
CB-5
14
CB-5 J1
13
J6
CB-4
12
11
15
J1
❸❷
❶
7
TX-20
MC-7
1x
M4
MC-6
1x
4.3mm
MC-5
1x
4.5mm
MC-2
1x
M4x10
Cables
MC-2
TX-20
16

16
J3
J100
❼
1
14
1
14
❻
CB-9
1x
1
14
J103
J2
❺
CB-8
1x
LS+
LS-
❹
2.5mm
17
EL-6
TX-10
❸
1.5mm
❷
2x
2x
❶
EL-5
1x2x MS-2
CA-5
1x
M3x5
MC-10
2x
Front & Lid

16
J3
J100
❼
1
14
1
14
❻
CB-9
1x
1
14
J103
J2
❺
CB-8
1x
LS+
LS-
❹
2.5mm
17
EL-6
TX-10
❸
1.5mm
❷
2x
2x
❶
EL-5
1x2x MS-2
CA-5
1x
M3x5
MC-10
2x
Front & Lid

18 19
1.5mm
2x
❻
❺
❹
CA-6
1x

18 19
1.5mm
2x
❻
❺
❹
CA-6
1x

20 21
Advanced system information
External size (WxHxD): 205 x 80 x 300 mm
(size incl feet, excl connectors)
®
Nilai 500DIY mono kit: 3.45 kg
0.0005% @ 20Hz < f < 20kHz, 4 , P<100WΩ
Dimensions and weight
(weight for the total assembled kit)
Distortion:
Input Impedance:
Output Impedance:
All loads max 30kHZ
100kΩ
90µΩ f < 1kHz
Source impedance: max 1kΩ
Voltage Gain: J200 open = 11.86dB
Frequency Response: +0/-3dB.
For more detailed information please refer to the
datasheet of each individual product on our
website.
Operation:
Performance:
All loads max 70kHZ
85 Ω f < 20kHzµ
J200 (3-4) = 27.88dB
+0/-0.01dB.
Load impedance: min 1Ω
J200 (1-2) = 21.75dB
Power Bandwidth: min 35kHz
Line input frequency: 47 - 63 Hz
Connector: 3-pin IEC 250Vac, 10A male.
Mid gain: 3.8Vrms
Line input voltage: 100 - 240Vac*
Input power:
Low gain: 12Vrms
Input sensitivity:
Depending on load, 650W max
Line input power
1
®
Nilai
Mono XLR
irreversible damage
Output:
Input:
Output power in 4 1% THD+N :Ω@
Channels:
Output power in 8 1% THD+N :Ω@
High gain: 1.9Vrms
260W
Technology:
Bindingpost
525W
* Operation beyond these limits may result in
System information Mono kit
®
Nilai 500 DIY
Trigger Jack 3.5mm (1/8") TS connection:
Wuntaix SCJ357M0NYS0B00L
Max: 18Vdc
Min: 6Vdc
Gnd
+12Vdc
Balanced XLR connection:
Neutrik NC3MXX-B or -BAG (male)
Pinout:
Neutrik NC3FXX-B or -BAG (female)
Pin 3: Negative (- or cold)
Pin 2: Positive (+ or hot)
Pin 1: Shield
This information is given for reference and to guide you in connecting your DIY-kit in the correct way.
Do not modify the internal wiring of the kit other than specified in the instructions.
Visit our website!
The latest datasheets and manuals can be found
there. Look into our FAQ and if you can not find the
answer there, you can also contact us and we will be
happy to assist you!
We continuously work to improve your experience
with our products. If you have suggestions, remarks or
found a bug, please contact us.
If you have any problem with your Amplifier kit please
consult this user guide. If this user guide is not
sufficient in order to your problem please contact
Hypex support departement.
Do you need additional assistance with assembling
your Amplifier kit? Watch our assembly instruction
video at the product page on our website.
Support
A No, we only offer a DIY building kit. We do not
offer any further assembly services.
Does this Amplifier kit work with my
QPreAmplifier?
A In basic this Amplifier works with all
PreAmplifiers with the right connections,
certainly DIYclassD PreAmplifier kits.
Do I need to solder anything?
Q
I do not have any technical experience,
Qcan I build this amplifier kit myself?
No! we have pre-fixed everthing for you. It’s
Ajust a matter of assembling all the parts with a
few basic tools.
Yes! even without any technical experience you
Acan build your own amplifier kit.
Do you offer a pre-assembled Amplifier
Qkit?
What kind of quality can I expect from this
QDIY Amplifier kit?
This kit contains Hypex Electronics Nilai®
Aamplifier technology, currently this is Hypex
Electronics best sounding amplifier technology.
Frequently asked
questions
Ÿ This kit is equipped with balanced inputs. If your
source does not provide a balanced output but
only an unbalanced output you can use one of our
interconnects to connect both properly.
Balanced/unbalanced connections
Ÿ Check optional trigger connections.
Ÿ The internal fuse may be blown. This fuse is not
use r r e plac e able . P leas e c o ntac t H ypex
Electronics for more information about service
and repair.
No Sound
Ÿ A protection might be triggered. Is the module
overheated? Try cycling the mains power.
Ÿ Check the volume and mute settings.
Ÿ Check the source signal.
Ÿ The AC-Terminal fuse may be blown. Disconnect
power cables and determine its status. If blown:
check all AC-cables for damage and correct
connections and fix problems. Replace the fuse
with a corresponding one.
No power
Ÿ Check the power outlet.
Ÿ Check if the signal is not inverted. Inverted signals
might cause one of your speakers to be out-of-
phase.
Ÿ Is the amplifier clipping?
Ÿ The Amplifier Kit will get warm/hot when used
intensively, this is normal and therefore no reason
for concerns.
Ÿ Use balanced connections for best system
performance.
Poor sound or noise
Hum
Heat
Ÿ Check all connections.
Ÿ Check all the cables.
Ÿ Use grounded wall sockets.
Troubleshooting