i-team i-gum User manual

R
USER MANUAL
CHEWING GUM REMOVAL , GAS PROVIDE ENERGY
GAS VERSION I-GUM
Revision date: 2017-08-31

CONTENTS
Important Safety Instructions
Package Check List
Preparation For Use
Installation 1
Installation 2
Using the machine
Turning OFF the machine
Maintenance
Trouble shooting
Machine Parts
Accessory
Exploded drawing and spare parts list
Product Specification
Instruction for control panel
01~03
04
06~09
05
06~07
08
09
10~11
11
12
13
Safety Data Sheet
14
15~22
23~26

Maintenance/servicepeople
(not i-gum operators)
need to keep a distance to
the integrated magnets in igum
for 6 inch/15 cm when they are
doing maintenance on igum
and are wearing a pacemaker,
this is just a precausion advise
READ ALL INSTRUCTIONS
BEFORE USING THE
MACHINE
R
LITHIUM-ION BATTERY
Nominal Voltage:14.8V
Energy/Capacity: 6.6Ah
SAFETY ADVICE
Do not crush, pierce
or damage in any way.
Do not heat or incinerate.
Do not short-circuit.
Do not dismantle.
Do not immerse in any liquids.
Only charge between
5 C~40 C/41 F~ 104 F
and discharge
5 C~45 C/41 F~113 F
R
oooo
o o o o
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE
01

IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE
DO NOT OPERATE THE MACHINE WITHOUT READING AND UNDERSTANDING THE
OPERATING INSTRUCTIONS. IF THE MACHINE IS OPERATED INCORRECTLY IT CAN POSE
DANGER TO THE OPERATOR AND OTHERS AND WILL INVALIDATE THE MANUFACTURERS
WARRANTY. BEFORE USE, READ AND UNDERSTAND THE FOLLOWING:
1. A Risk Assessment for the works to be undertaken.
2. MSDS Chemical Data Sheet.
3. Risk Assessment for Chemical use.
IMPORTANT NOTICE:
Cautions when using the machine:
Keep the body upright at all times when operation or when chemical or
batteries inserted.
The rechargeable battery has been designed to be fully charged BEFORE
each use
Only use the approved solution and batteries for the safe use of the machine.
Using other consumable items in the machine invalidated the warranty and
will lead to damage of the internal parts of the machine and also may pose
a risk to the operative.
Make sure the operator has read and understood these instructions before
attempting to use the machine and is fully trained in its operation.
Consumable Items:
Chemical (2 Litres) will last for approximately 2 hours of continual use. 4x chemical
bottles will last for approximately 8 continual hour’s operation.
The brushes will wear according to the surface being cleaned. Each Brush will last
for approximately 4 hours. 2x Brushes will last for 8 hours continual operation.
Only use the specifically designed brush as this has a jet incorporated for machine
to work correctly.
Choose a steel wire brush for solid urban surface such as concrete, natural stone,
tarmacadam, asphalt and other common urban surfaces. Choose a nylon brush
for soft surfaces such as manmade flooring, sandstone, heavy-duty carpet.
02
4. LPG data sheet.
Before inserting the LPG Gas and gum removal chemical correctly fit the
backpack to the operator by adjusting the straps to fit. The backpack has been
designed to be kept upright at all times when the LPG and gum removal
chemical are inserted. This is important to the operation of the machine.

IMPORTANT NOTICE:
Always complete a test patch on the above surfaces to make sure no damage occurs to
the flooring of surface
Service Pack:
When a machine is purchased, it require a service pack. Each service pack provides a
continuous 8 hours operation and consists of:
4x Chemical Bottles
2x Nylon wire Brush
3x Steel wire Brush
03
Warranty:
The Chewing Gum Removal machine should only be operated with the service
packs supplied. Using alternative supplies may cause damage to the machine
and cause a risk to the operative. Using alternative supplies voids manufacturer's
warranty.
2x LPG Gas Cartridges

Package Check list:
Broom with telescopic handle 1x LPG Gas Cartridges 2x
Nylon Wire Brush 2x
Water Drop Disk 1x Brushes Storage Tube 1x
Accessory:
Battery Charger 1x Cable For Charger 1x Steel Wire Brush 3x
MAIN BODY 1x LANCE 1x
Machine:
When you open the color box and you can find the parts as below showing:
Chemical bottles 4x
04

Machine parts:
Lance
Control panel
Trolley handle
Broom
Shoulder harness
& Waistband
Water drop disk
Wheel
Hose
Fluid inlet hole
Brushes Storage Tube
Battery Power Display
Gas Cartridges Drawer
Drawer Handle
Timer
05
Exhaust
Brush
Water level
Power Switch
Fuse
Charger Plug
Self-lock switch for gas valve

Installation1.
1. Install the water drop disk to body. 2. Screw a steel wire or nylon wire brush
onto the end of the nozzle of the lance.
close
open
3. Place the lance in the lance holder of body. There are 2 magnets can attract the lance.
(When you are in cleaning working or carry the machine on back, the lance should be taken on hand.)
06
Preparation For Use

5. Assembly the brush to telescopic wand for BROOM.
4. Open the brushes storage tube cap and you can place the other 4x brushes in the tube.
insert the brushes storage tube to the holder of body.
6. Insert the broom to broom holder of body.
(When you are in cleaning working or carry the machine on back, the broom should be taken on hand.)
07

Open the gas cartridges storage drawer and install the gas cartridges to gas caps.
Then push the storage drawer back (must be pushed to location).
(You also can install one gas cartridge, it is safety and the machine also can work.)
open
3. Insert Batteries
Installation2.
Before operating the machine:
1. Ensure that the battery has been fully charged before each operation.
2. Pour Chemical into fluid tank.
Take off the fluid inlet cap and then pour chemical into the fluid tank. (one battle is for each time).
08
Preparation For Use
close
Turn the gas cartridges to right
to tighten it, one by one.
DO NOT PLACE THE CHARGER IN PACKAGE,
WHEN IT IS IN CHARGING. BECAUSE CHARGER
NEED COOLING.

INSTRUCTION FOR CONTROL PANEL
ON/OFF Button: Power supply for handle control.
IGNITION Button: Ignite the gas in lance
H/M/L Button, Adjust the fluid flowing in low speed/middel speed/high speed.
(Flowing speed indicator light will be bright and pump will work)
Battery Power Indicator
00000000
Timer for machine
using hours
Main Switch
For Power Supply
INSTRUCTION FOR BODY CONTROL PANEL
INSTRUCTION FOR WATER LEVEL INDICATOR
The fluid tank capacity is 2.5L. Each use,
we can input one chemical bottle to tank.
When shortage for fluid, the LED light of tank
side will flush.
When you pour Chemical into fluid tank, And
then restart the main switch of body, the LED
light will be bright.
09
Preparation For Use
Flowing speed indicator light
(Spacing 5 seconds, press once）
Cooling fan indicator light

Using the machine:
LOGIC FOR OPERATION
Turn on the Mainswitch on body
Turn on ON/OFF button on lance control panel
Press H/M/L button on lance control panel
INDICATOR LIGHT will be bright, and pump will run in full speed.
Turn on Self-lock switch for gas valve, and Gas will come out to lance
press the IGNITION button for 2 seconds and you will hear the fire sounds in lance,
Cooling fan will work and the cooling fan indicator light will be bright.
After few seconds, The fluid come out from brush of lance
Fluid in boiler will start to heat and cooling fan will be bright.
After about 10~20 seconds, Fluid will be heated to steam,
and steam will come out from brush of lance
Place the brush on the piece of flattened gum, Agitate the flattened
gum with the brush until you see it disintegrate by using circular
motions-do not scrub or apply pressure. The weight of the lance with
agitation is all that is required.
Remove the lance from the gum and use a broom to sweep across
the area to ensure the gum has been destroyed or if further cleaning
is needed.
As gum deposits are all different there will be varying times taken to
destroy each piece.
10
Steam will come out from brush of lance, change the flowing speed by
pressing the H/M/L button.
(First use, need to wait about 1 minute)
Open the gas storage drawer and
turn on the gas valve, Then push
the drawer back(must be pushed to
location).

Turning OFF the machine:
12
5
11
Turn off the gas safety switch first
(The button should be high)
ON/OFF Button
Turn off the on/off button, pump and pump
light will be off, but cooling fan and cooling fan light
will be off after delay 3 minutes(Because the lance
need to be cooled).
Cooling
fan light
Turn off the Main switch on body. Open the drawer and close the gas valve.
34
Screw out and take off the 2 Gas bottles from drawer.

Maintenance
1. During interruptions of the cleaning process, always place the lance
into the holder of body. And always place the machine upright on dry
floor surface.
2. When the water drop disk is full, please empty and wash it, and then
install back to body.
3. The yellow rubber block must be closed to the inlet hole, when you
finish the water input. Otherwise, the dust will come into water tank.
Always DO NOT pour thesewage into the tank.
Only use the approved solution chemical.
4. The first charging for battery, please charge full,100% completely.
Machine maintenance
The GAS VERSION I-GUM machine requires very little maintenance. Wipe down the
machine periodically with a clean cloth. And wipe down the lance, or change the new brush
for lance. DO NOT spray water directly over the top of machine or top connector cap.
5. The top cap for hose connector is assembled by factory, Always
DO NOT to disassemble the hose connector cap except repairing.
The connectors are showed as the picture:
connect to black GAS pipe
connect to transparent FLUID pipe
connect to 10 poles
circle male connector
12
DO NOT PLACE THE CHARGER IN PACKAGE,
WHEN IT IS IN CHARGING, BECAUSE CHARGER
NEED COOLING.

Trouble shooting
PROBLEM CAUSE SOLUTION
No power to machine Battery is bad Replace a new battery
Power switch failure Replace power switch
cable or wire in hose broken Replace cable or wire for hose
No steam come out The fluid tank do not have chemical Input the chemical from bottes
No Gas cartridges be installed Install Gas cartridges
The pump do not run Replace pump
The steam outlet hole is blocked Change to use a new brush
Water level indicator
LED light is flushing
The chemical is shortage in tank Pour the chemical into tank
Fluid leak from tank
The outfall block rubber is opened Close the outfall block rubber
Fluid tank is broken Replace fluid tank
The machine is being overturn Make the machine upright and the
fluid can come out from bottom
Battery can not be
charged
The battery life is over Change to use new battery
Charge is bad Repair the charge or change a new
one
13
Ignition can not work Ignition button is bad Replace a new control panel PCB
Electronic igniter Replace a new electronic igniter

PRODUCT SPECIFICATION
Gas version i-gum
14
Product Size (body unit): 347*330*500 mm
Lance Size: 60*1100 mm
Weight (except accessory): 10.0 kg
Lance Weight: 1.8 kg
Broom Extended Length: 1.3 M
Li-ion Battery: 14.8V, 6.6Ah
Tank Capacity: 2.5 L
Operation Time of Battery :
about 3days continuous use
Gas Drawer Capacity: 631ml*2 bottle of gas
Fluid Flow Speed Class:High, Middle, Low
Drawer Storage For Gas Bottle: YES
Trolley Handle: YES
Transport Wheel: YES
Backpack For Body Unit: YES
Water Shortage Warning
: YES

I-GUM LANCE EXPLODED DRAWING
Exploded drawing and spare part list
15
page 1/8
1
2
3
4
5
6
7
8
9
26
10
11
12
14
15
17
18
19
22
23
24
25
34
31
27
30
37
33
35
32
28
36
39
20
16
38
40
13
29
21

LANCE
spare parts list
16
page 2/8
Item Part No. Discription Material Q'ty
1 106.0002.7 Control panle PCB gas version PCB board 1
2 97.2004.3_remark Handle cover right, 431C PA66+20%GF 1
3 97.2003.3_remark Handle cover left, 431C PA66+20%GF 1
4 106.0002.2 Handle wand AL
1
5 106.1151.0 Soft rubber for lance handle Rubber
1
6106.1111.5
M4*6 Hex-sokect botton head screw SUS 304
10
7106.1002.1
Lance Al top cap AL
1
8106.0098.0
Fan DC12V 40*40*28mm PA66, Cu
1
9106.1111.20
M3*35 pan head machining screw SUS 304
4
10 106.0000.3
Lance carbon fibre sleeve, Grey 432C Carbon fibre
1
11 106.2149.0
Steel part for Lance top magnet SUS 201
1
12 02.0005.1
Sealed rivet Alu 4*8mm AL
2
13 106.0104.0
Warning Label Paper
1
14 106.1163.0
Exhaust cover protective sleave PC,UL94-V0
1
15 106.0089.0
Exhaust cover with plating Cr. AL
1
16 106.1111.16
M4*10 Hex-sokect botton screw SUS 304
2
17 106.0013.0
Brush with nylon wire, 1.5mm outlet hole PA66+20%GF
2
(17)
106.0014.0
Brush with steel wire, 1.5mm outlet hole PA66+20%GF
3
18 106.2171.0
Rubber for brush holder Rubber
1
19 72.0206.1
Screw counter sunk bolt M4*8 SS SUS 304
3
20 106.0005.9
Bottom steel ring for lance SUS 403
1
21 72.0206.0
M4*10 counter sunk bolt screw SUS 304
2
22
S.106.0005.0
Assy heat exchanger (boiler assm unit) SUS 304
1
23
S.106.0111.0
Gas burner assembly unit Cu-H68
1
24 106.2168.0
Support cap for hose connector
PA66+15%GF
1
25 106.0021.0
Hose connector cap
POM, UL94-V0
1
26 106.0113.0
Electronic igniter -
1
27
S.106.2046.1
10 poles circle male connector with cable PVC, Cu...
1
28 106.2105.0
Hose end cap ABS
1
29 106.0148.0
Pipe quick connector for fluid output -
1
30 106.0023.0
Protection hose outside
25mmX1.5m PU, Steel 1
31 106.0118.0 Transparent pipe for fluid output 6x4mm PU 2.5M
32 106.2079.2 Connector wire for handle to fan and igniter PVC, Cu... 1
33 106.1144.0 Rubber stoper for handle Rubber 1
34 106.0119.0
Gas pipe black
6*4mm PU 2.2M
35 106.0096.0 Self-lock switch for gas valve - 1
36 00.0002.62 Screw st 3*14 cross SUS 304 3
37 106.2105.1 Hose end cap for handle ABS, UL94-V0 1
38 106.1111.4
M3*6 pan head self-tapping screw SUS 304 2
39 106.0002.6
Cantrol panel ABS, UL94-V0 1
40 106.0002.5
Control panle layout sticker PC 1

BODY UNIT EXPLODED DRAWING1 17
page 3/8

BODY UNIT EXPLODED DRAWING2 18
page 4/8
53
54
55
56
61
62
63
65
67
69
70
72
73
71
57
58
59
66
68
64
60