I-View EPOC-131HP-O User manual

1
Product Overview:
1.) Terminal block:DC 12V/4A power output.
2.) Yellow LED: The LED indicates the power status. On: Power on; Off: No power.
3.) Ethernet/PoE: RJ45 connector, attaches to POE IP Camera or Hub via Cat5, 5e, 6 or 7 patch cables.
4.) Green LED:The LED indicates the communication status. Flash: Communicate with Traffic; Off: No
connection.
5.) Data: RJ45 Female (No LED) or BNC connector allows 10/100 Base-T Ethernet and PoE power to be
transmitted using Cat. 5 or better UTP cable with 4 pair wires or Coaxial cable.
6.) Cable gland:Passing through gland plates to attach and secure coaxial cable and RJ45 UTP Cable.
7.) Fix Hole: 4 Wall Mount holes to fix EPOC-131HP-O on the wall position.
Packing Check list:
Carefully unpack and check the package box if the following items are included:
EPOC-131HP-O x 1 ea
Hexagon wrench 3.0mm L type x 1 ea
Cable gland x 2 ea
Menu x 1 pc
DC56V/1.28A AC power adapter x 1 ea (Optional)
Installation Steps:
IP camera end
1. Loosen the sealing nut of cable gland, then pass through UTP (or coaxial) cable and DC power jumper into cable
gland. Please make sure the polar of DC power output when plug the DC power jumper into terminal block.
2. Make the RJ45 (BNC) connector with the UTP (Coaxial) cable.
3. Connect the IP camera RJ45 connector to the 10/100BaseT Ethernet port of EPOC-131HP-O using a standard
Cat5/6 cable of maximum 100 m (328 feet) in length. Connect one end of the long UTP cable EPOC-131HP-O.
4. Loosen 4 hexagon screws of bottom panel with hexagon wrench.
To avoid the waterproof problem, please DO NOT open the TOP PANEL of EPOC-131HPJ-O.
5. Loosen the lock nut of cable gland, then fix cable gland with bottom panel.
6. Push the EPOC-131HPJ-O’s board to top side of housing; then tighten the sealing nut with the UTP cable.
7. Tighten bottom panel with housing with 4 hexagon screws.
8. When the IP camera and EPOC-131HP-O cannot receive power through the UTP cable, even through using plug
DC56V power adapter for EPOC-131VAJ. Please refer to “Power Distance VS. Cable Impedance” table.
EPOC-131HP-O Ethernet/PoE Extender over 2-Wire Installation Guide
V1.3
5
3
1 5 2
4
7
6

2
Product Application Diagram
The Ethernet over UTP (Coaxial) Cable system provides high power for the IP devices such as IP PTZ camera.
The system supports virtually any type of Cat. UTP wire, including such as Cat.5, 5e, 6, or 7 cable. And different
wire types can be concatenated together, as needed. It also supports the coaxial cable.
To avoid the interference signal, we strong recommend using the Cat. STP cable for Ethernet/PoE signal
transmission when there are more 16 pcs EPOC-131 VA /131VAJ install at the same Hub site.
Application Diagram
The IP camera and EPOC-131HP cannot receive power through the UTP cable. Please do as below:
1. POE+ Hub or plug DC56V power adapter for EPOC-131VA or EPOC-131VAJ .
2. Plug the DC48V power adapter into the EPOC-131HP-O will be needed at this end. Please refer to “Power
Wattage VS. Cable Distance” table or visit www.i-view.com.tw
Power Wattage VS. Cable Distance

3
Data Rate VS. Cable distance
LED Function table
Name Color Status Function
Pwr Yel low On Power is on
Off Power is off
Eth Green Flashing Communication is OK with Traffic
Off No communication
Link Green On Connection is OK; (It take 10 sec. for LED on)
Off No connection
PoE Green On PoE is offering
Off No PoE offer

4
Specification:
1.Distance and number of devices supported may be lower due to power supply capacity and wire voltage-drop. The bandwidth is
dynamically allocated (shared based on traffic), and decreases with wire distance.
Phone: [phone] Fax: [phone]
Mail: [e-mail]
ITEM \ MODEL EPOC-131 VA EPOC-131 VA J EPOC-131HP-O
Ethernet
Connector RJ-45 RJ-45 RJ-45
Connectivity 10/100 Base-T auto-negotiation, auto MDI / MDX crossover
Wire type Cat5 or better
Distance Up to 328 feet (100m)
Cable Link
Connector BNC RJ-45 BNC/RJ-45
Type Receiver (Hub Site) Transmitter (Camera Site)
Wire type Coax, single- or multi-pair UTP, 18/2, or STP wire
Distance Up to 600 Meters (1980 feet)
Topology Supports Star, Daisy-Chain, or any combination
Encryption 128-bit AES
Latency 3 ms
BandwidthTotal network bandwidth 150 Mbps; with dynamic bandwidth allocation
Power
Power Source PoE Hub; DC44～56V PoE
Power Output PoE (RJ-45 via 4 pairs
UTP cable)
PoE (BNC via Coaxial
cable)
50W; DC12V/4A
Physical
Waterproof None None IP 66
Dimensions (mm) 100 x 55 x 34 100 x 55 x 34 128 x 102 x 36
Weight 140g 140g 310g
LEDs
Status indicators
Cable link
Ethernet Power
Ethernet link/activity
Cable link
Ethernet Power
PoE Connection
Ethernet link/activity
Ethernet Power
Ethernet link/activity
Environment
Temperature Operation: -40℃to 60℃/ -40℉to 144℉
Humidity 20% ~ 85% non-condensing
Power consumption ≤ 2W
Transient immunity 20µS x5 3,000A, 6,000V; ESD 20KV, 200pF
1
1