i3 International i3C760 User manual

• DESCRIPTION
User can use the control panel via RS-485 interface or
RS-422 interface to control the camera.The camera must
surport the PELCO P/D protocol and baud rate should be
1200/2400/4800/9600.
• PARTS' NAMES AND CONNECTIONS
BACK PANEL :
1. RS-232 FUNCTION
A personal computer can communicate with control panel
through DSUB 9 RS232 port,then via RS-485/RS-422 of
control panel,access of read/write of camera is possible.
Please read this manual thoroughly before use, and keep it handy for future reference
Control Panel
ZEIM-0050715G Ver.C.760.A.4
Instruction
Manual
1NC 6NC
2TX 7NC
3RX 8NC
4NC 9NC
5GND
DSUB-9 PINOUTS
5 4 3 2 1
SW5 Interface DIP
ON RS-485
OFF RS-422
SW6 Turbo DIP
ON ON
OFF OFF
SW3 Interface DIP
ON Pelco D
OFF Pelco P
No Description No Description
1 LED Display 9 Keypad (Numbers 0
through 9)
2 Shift LED 10 Near Key
3 Shift Key 11 Far Key
4 Pattern Key 12 Close Key
5 Preset Key 13 Open Key
6 Joystick 14 Zoom Out
7 Clear Key 15 Zoom In
8 Camera Selection Key
• PANEL FUNCTION
7 10 14 15
CAM
7
4
CLEAR0 ZOOM OUT
8 9
56
NEAR
ZOOM IN
FAR
PRESET
PATTERN
1 32 OPEN
SHIFT
CLOSE
4 5 3 2 1
9
8
13
12
11
6
3.RJ45 PINOUTS ( RS485)
1.DATA+ 5.NC
2.DATA- 6.NC
3.NC 7.NC
4.NC 8.NC
4.RJ45 PINOUTS (RS-422)
1.TX+ 5.GND
2.TX- 6.NC
3.12VAC /DC 7.RX-
4.Nonpolar 8.RX+
SW7 SW8 Buad Rate DIP 7 8
1 OFF OFF 1200
2 ON OFF 2400
3 OFF ON 4800
4 ON ON 9600
Notes: Need to reset power after switch setting.
2. SWITCH SETTINGS
Users can setup the prtocol and buad rate by using
DIP switch.The table below will provide DIP switch
information.
DIP SW Description
SW1,2,4 MUST be OFF
SW3 Protocol setting
SW5 RS-422/ RS485 Select
SW6 Turbo ON/OFF
SW7~SW8 Baud Rate Select
1 2 3 4 5 6 7 8
RJ45 of the control panel

Control Panel
INSTRUCTION MANUAL
•SPECIFICATION
• Connecting the Keyboard
1.Keyboard and Receiver Wiring
(RS-485 INTERFACE)
2.Keyboard and Receiver Wiring
(RS-422 INTERFACE)
NOTE : A DC12V DC Jack power input is also available on rear panel of control panel
1. Electrical
Input Voltage 12VAC/12VDC
Power Consumption 2.5W
Key Board Connector RJ45, 8-pin, modular (female)/
D Sub9, 9-pin (female)
Key Board
Communication
Direct mode
Interface :
RS-485, RS-422, RS232
Protocol : Pelco P, Pelco D
Baud rate:
1200, 2400, 4800, 9600
Parameters : 8 data bits,
no parity, 1 stop bit
LED Display 7-segment display, 3 cells
2. General
Keyboard Keypad Mechanical
Joystick 2-axis, vector-solving, return-
to-center
Dimension 245mm x 175mm x 55mm
Unit Weight MAX : 1.2 Kg
3. Environment
Operating
Temperature
-100C to 500C
Storage
Temperature
-200C to 600C
Humidity 10-90% non-condensing
4. Accessories
Cable 3.5 m, RJ-45 data cable
Adaptor (Optional) AC 90V~260V /12V 500mA
Phone Box
(Optional)
RJ-45 Type
Panel Function
Ke
y
board and Receiver Wirin
g(
RS-485 INTERFACE
)
TO RECEIVER(s)
DATA+
DATA+
DATA-
DATA-
RJ-45 wall Block Termial
s
ADAPTOR DC 12V
[4] [5]
15 Zoom in (only for A-type)
Connecting the Keyboard
13 Close key
14 Zoom out (only for A-type)
11 Far key
12
8 Camera selection key
Open key
9 keypad ( numbers 0 through 9 )
10 Near key
6 Joystick
7 Clear key
4 Preset Key
5 Pattern key
2 Shift key
3 Shift LED
DescriptionReference No.
1 LED display
Control Panel
2.SWITCH SETTING
S
Keyboard and Receiver Wiring(RS-422 INTERFACE
)
TO RECIVER(S)
TX
+
RX+
TX-
RX-
RX+
TX+
RX-
TX-
SW7 SW8
OFF
OFF
3.RJ45 PINOUTS
(
RS485
)
RJ-45 wall Block Termials
4.RJ45 PINOUTS
(
RS-422
)
DC/AC 12V
ADAPTOR 12VAC/12VDC

5.DC JACK 12VDC
[06] [3]
RS-422
ON
SW6 Turb
o
ON
OFF OFF
ON
ReserveON
ON
ON
ON
OFF
RS-422 / RS-485 Select
Protocol setting
Turbo ON/ OFF
Description
Reserve
3
DIP SW
SW1~SW4
SW5
SW7~SW8
SW 6
Interfac
e
SW5
OFF
RS-485
OFF
Input voltage : 12 VDC
Protocol
Pelco P
Reserve
Reserve
1
2
4
1. TX+
2. TX-
3. 12 VAC/DC
4. Nonpolar
1. Data+
2. Data-
3. NC
4. NC
5. NC
6. NC
7. NC
8. NC
5. GND
6. NC
7. RX-
8. RX+
Control Panel